Vicon XX152-02-00の取扱説明書

36ページ 1.5 mb
ダウンロード

ページに移動 of 36

Summary
  • Vicon XX152-02-00 - page 1

    XX152-02-00 FIXED CAMERA DOME Vicon Industries Inc. does not warrant that the functions contained in this equipment w ill meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for t ...

  • Vicon XX152-02-00 - page 2

    ...

  • Vicon XX152-02-00 - page 3

    FCC Notice Note: Complies with Federal Communications Commi ssion Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacture r’s instruction, may cause interferenc e to radio and ...

  • Vicon XX152-02-00 - page 4

    Important Safeguards 12. Power Cord Protection - Power supply cords should not be routed in trafficked areas or in tight spaces wher e they w ill be pinched or used to bear weight. Allow some slack in the cord where it enters the unit. 13. Outdoor Cable Grounding - Use only grounded outdoor cables to protect against volt age surges and static charg ...

  • Vicon XX152-02-00 - page 5

    Contents Quick Inst allation ............................................................................................................. ...ii Introduc tion ................................................................................................................... ......1 Installa tion ..................................................... ...

  • Vicon XX152-02-00 - page 6

    Quick Installation In-Ceiling - No Access to Ceiling ii • Quick Installation XX152-02-00 Rev 1204 Surv eyorVFT Fixed Camera Dome ...

  • Vicon XX152-02-00 - page 7

    In-Ceiling – Access to Ceiling XX152-02-00 Rev 1204 Surv eyorVFT Fixed Camera Dome Quick Installation • iii ...

  • Vicon XX152-02-00 - page 8

    Pendant - Indoor iv • Quick Installation XX152-02-00 Rev 1204 Surv eyorVFT Fixed Camera Dome ...

  • Vicon XX152-02-00 - page 9

    Pendant – Outdoor XX152-02-00 Rev 1204 Surv eyorVFT Fixed Camera Dome Quick In stallation • v ...

  • Vicon XX152-02-00 - page 10

    ...

  • Vicon XX152-02-00 - page 11

    Introduction The information in this manual covers the installati on, operation, and maintenance of the SurveyorVFT Series of Fixed Camera Domes. This unit should only be inst alled by a qualified technician using approved materials in accordance with national, state and local wiring codes. Read this manual through completely before attempting inst ...

  • Vicon XX152-02-00 - page 12

    UTP Receivers V212-NVT 7631 Receiver, converts UTP video to composite up to 500 ft from transmitter V213-NVT 6518 Receiver, converts UTP video to composite up to 1000 ft from transmitter V652R-NVT 7453 Receiver, converts UTP video to composite up to 3000 ft from transmitter (does not support Vicoax systems) V1613-NVT 7648 16-channel Hub receiver, c ...

  • Vicon XX152-02-00 - page 13

    SurveyorVFT Fixed Dome Components The SurveyorVFT fixed camera dome units consist of an enclosure/housing, a camera mechanism, a shroud, and a smoked (indoor) or clear (outdoor) lower dome. Enclosure The enclosure is a metal shell that houses the camera me chanism for the in-ceiling model. A safety cord and clip are provided to connect to the camer ...

  • Vicon XX152-02-00 - page 14

    Mounting the Unit In-Ceiling Mounting The SurveyorVFT fixed dome rests on the ceiling material and occupies the space between the lower ceiling and upper building frame. There are two methods of installation. The first method can be used for ceilings with no access to the space above, as in a typical hard material ceiling. The second method is used ...

  • Vicon XX152-02-00 - page 15

    2. If cables are used without the use of flexible conduit: a. Remove the enclosure top by loosening the 3 screws. Remove the conduit fitting by loosening the nut and sliding it out. Install the supplied stra in relief fitting in its place and re-attach the top and route cables through the strain relief fitting. 2. a. e enclosure near the hole in th ...

  • Vicon XX152-02-00 - page 16

    3. Working above the ceiling, remove the enclosure top by loosening the 3 screws and lifting it off. If cables are used without the use of flexible conduit: 4. uit cables through the conduit fitting. Continue with the section on Cable Connections. Optiona If it is necessary to provide independent support for t he SurveyorVFT fixed dome other than c ...

  • Vicon XX152-02-00 - page 17

    Installation of Optional In-Ceiling Mounting Kit rveyorVFT fixed camera dome can (such 1. Install the 2. the 1.5-in. NPT pipe, 3. 4. When it becomes 5. Verify that each cable dro length. 6. Lift the camera mechanism up to the housing and atta ch the housing’s safety cord clip to the camera mechanism’s tab. Allow the Surv eyorVFT mechanism to ha ...

  • Vicon XX152-02-00 - page 18

    Outdoor Pendant The outdoor pendant model mounts on a Vicon mount or a 1. 5-in. vertical pipe with an appropriate coupling. e area around the inte The outdoor version includes a sunshield, heater and weather protection. Be sure th selected location is clear of obstacles (such as steel beams, headers, pipes, electrical wiring, etc.) that would rfere ...

  • Vicon XX152-02-00 - page 19

    Camera Power Connections Note: Vicon systems and components, like most electroni c equipment, require a clean, stable power source. Voltage irregularities such as surges, drops, and in terruptions can affect the operation of your equipment and, in severe cases, damage certain co mponents. Vicon strongly recom mends the use of line conditioners, vol ...

  • Vicon XX152-02-00 - page 20

    DIP Switch Settings There is a DIP switch on the front camera board that a llows the selection of: Switch 1 - ALC (OFF) or ELC (ON); Switch 2 – Internal (Crystal) Synchronization (O N) or Line Lock (OFF); Switch 3 – AGC (ON or OFF); 4 – BLC (ON or OFF). ALC setting is for external autoiris and ELC setting is for internal autoiris. The ght cam ...

  • Vicon XX152-02-00 - page 21

    Figure 5 Potentiometer/DIP Sw itch Location Figure 6 DIP Sw itch Settings XX152-02-00 Rev 1004 Surv eyorVFT Fixed Camera Dome Installation • 11 ...

  • Vicon XX152-02-00 - page 22

    Final Installation In-Ceiling After all cabling is complete, (if not previously done) connec t the enclosure’s safety cord clip to camera mechanism to allow the mechanism to hang fr om the enclosure. Align the 2 slots on the camera mechanism with the tabs in the enclosure, being sure to match up the arrows on both the drive and in the enclosure. ...

  • Vicon XX152-02-00 - page 23

    Figure 8 Camera Mounting Bracket Adjustment – 2.6-6 mm Version Show n with the place on 9. Insert the clip of the safety cord on the lower dome into the hole in the enclosure. Refer to label in the enclosure. Lift the lower dome up to the SurveyorVFT and align the molded tabs on the lower dome recesses on the inner enclosure. Press the lower dome ...

  • Vicon XX152-02-00 - page 24

    Indoor Pendant After all the cabling is complete, push the SurveyorVFT camera mechanism straight up into the housing. Align camera mechanism with the tabs in the enclosure, being sure to match up the arrows on both the mechanism and in the enclosure. Insert the camera mechanism into the enclosure there is no extra slack in the cab ling that will in ...

  • Vicon XX152-02-00 - page 25

    Outdoor Pendant Note: Assure that there is no extra slack in the cab ling that will interfere with proper installation and After all the cabling is complete, push the SurveyorVFT camera mechanism straight up into the housing. Align the 2 slots on the camera drive with the tabs in the enclosure, being sure to match up the arrows on both the drive an ...

  • Vicon XX152-02-00 - page 26

    Disassembly The SurveyorVFT Fixed Camera Dome disassembled by removing the camera mechanism camera mechanism while assembling or disassembling. 1. Gently pull down on the lower il all molded tabs snap out of place. 2. 3. cables. 1. On outdoor version only, loosen the four (4 2. Gently pull down on the lower il all molded tabs snap out of place. 3. ...

  • Vicon XX152-02-00 - page 27

    Operation When power is applied to the camera, the Surv eyorVFT fixed dome view s the selected scene. Maintenance The SurveyorVFT Fixed Camera Dome requires no scheduled maintenance except for the occasional cleaning of the lower dome. Care and Cleaning of Lower Dome 1. Always handle the lower dome by the fl ange and avoid touching the inside surfa ...

  • Vicon XX152-02-00 - page 28

    Shipping Instructions 1. Call or write Vicon for a Return Authorization (R.A .) at one of the locations listed below. Record the name of the Vicon employee who issue auge, NY 11788 Vicon Industries Ltd Brunel Way Fareham, PO15 5TX Phone: +44 (0) 1489 566300; Fax: +44 (0) 1489 566322 2. Attach a sheet of paper to the unit with the following informat ...

  • Vicon XX152-02-00 - page 29

    Reference Coaxial cables used to route video signals to and from the unit must meet the video reco mmendations in this section. Caution: Careful selection of the proper cable is ess ential to obtain the best performance from this equipment. Vicon assumes no responsibility for poor performance when cables other than those recommended are installed. ...

  • Vicon XX152-02-00 - page 30

    Twisted-Pair Cable Caution: Careful selection of the proper cable is ess ential to obtain the best performance from this equipment. Vicon assumes no responsibility for poor perform ance when cables other than those recommended are installed. at er ia ls Use a pure copper stranded or solid conductor w ith or without a tin plating to obtai n a low DC ...

  • Vicon XX152-02-00 - page 31

    Technical Information Current: Outdoor: 1.1 A. sent the conv ersion of 100% of the electrical energy to eat. Actual percentage of heat generated will be less and will vary from product to product. These figures are provided as an aid in deter mining the extent of cooling required for ELECTRICAL Input Voltage: 24 VAC ±20%. Indoor: 0.4 A. Pow er Con ...

  • Vicon XX152-02-00 - page 32

    Dimensions: In-Ceiling Height: 9.7 in. (246 mm). Total Diameter: 7.1 in. (180 mm). . Total Diameter: 8.0 in. (203 mm). Dome Diameter: 5.9 in. (150 mm). Outdoor Pendant eight: Approximately 2.5 lb (1.1 kg). onstruction: Plastic, aluminum and steel. 0° C). Storage Temperature Ra -40 to 150° F (-40 to 65° C). Storage Humidity: Up to 90% relative, n ...

  • Vicon XX152-02-00 - page 33

    1004 SurveyorVFT Fixed Camera Dome Technical Info n • 23 rmatio 1/6 1/6 1/6 1/6 1/ 1/ 1/6 Table 3 Camera Specifica ns od ma ev Co Mo nes) Sensitivity fc (lux) zation E nic ig No ise off) off) nal- R dB dB to- atio (AG S > > lectro (se 1/60 – 1/100,000 /50 1/60 – 1/100,000 (1/50 PAL) – 1/ /50 – 1/ /50 – 1/ /50 – 1/ /50 –1/1 (1/ ...

  • Vicon XX152-02-00 - page 34

    24 • Tech nical Information XX152-02-00 Rev 1204 SurveyorVFT Fixed Camera Dome Lens Specifications Model Focal Length (mm) Field-of-View Horizontal Vertical SVFT-C266M/ SVFT-C266M-C 2.6-6 varifocal with manual iris 106° - 47.6° 78.2°- 35.8° SVFT-C266A/ SVFT-C266A-C 2.6-6 varifocal with autoiris 106° - 47.6° 78.2°- 35.8° SVFT-C550M/ SVFT-C ...

  • Vicon XX152-02-00 - page 35

    Vicon Standard Eq ment Warrant uip y Vicon Industries Inc. (the “ be free from defec ts in material and workmanship under Normal Use from the date three y ears, w ith the following exceptions: 1. VCRs, all models: Labor and video heads warranted for 120 day s from date of or iginal retail purchase. All other parts warranted fo retail purchase. 2. ...

  • Vicon XX152-02-00 - page 36

    Vicon Industries Inc. Corporate Headquarters Fax: 6 51-CCT 288) 31-9 V (2 ✆ Infofax: 800-287-1207 nite om +44 (0) 1489 566300 Fax: +44 (0) 1489 566322 Leuv t 5 enses eenweg 42 B-1930 Zaventem Belgium 2 (2) 712 8 80 878 Far East Office Hong Kong 52) 118 Internet Address: www. v ic on -c ct v. c o m 3 7 Fax: 32 (2) 712 1 Unit 5, 17/F, Metropole Squ ...

メーカー Vicon カテゴリー Digital Camera

Vicon XX152-02-00のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- XX152-02-00の取扱説明書
- Viconの製品カード
- パンフレット
- またはVicon XX152-02-00の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Vicon XX152-02-00の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Vicon XX152-02-00の取り付け説明書、サービスマニュアル、簡易説明書、またはVicon XX152-02-00のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Vicon XX152-02-00の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Vicon XX152-02-00デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがVicon XX152-02-00を使用するのを助ける技術的文書のことです。説明書は通常、全てのVicon XX152-02-00ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Viconの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Vicon XX152-02-00の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははVicon XX152-02-00の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Vicon XX152-02-00に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Vicon XX152-02-00デバイスの基本機能を使うにあたってのヒント。 Vicon XX152-02-00のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Vicon XX152-02-00に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるVicon XX152-02-00のメーカー/サービスへの連絡先に関する情報。

Vicon XX152-02-00についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもVicon XX152-02-00の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがVicon XX152-02-00で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)