Kawasaki 840139の取扱説明書

20ページ 0.99 mb
ダウンロード

ページに移動 of 20

Summary
  • Kawasaki 840139 - page 1

    MODEL #840139 13" DRILL PRESS INSTRUCTION MANUAL FOR CUSTOMER SERVICE POUR LE SERVICE APRÉS VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1-800-590-3723 Printed in China 87-1904-60957 KAW ASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™ MOTORS CORP ., U.S.A., WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT . CONSUMER INQUI ...

  • Kawasaki 840139 - page 2

    INSERTING LASER BA TTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SECTION FOUR MAINTENANCE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Kawasaki 840139 - page 3

    GENERAL SAFETY RULES – FOR ALL ELECTRIC POWER TOOLS READ AND UNDERST AND ALL INSTRUCTIONS. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injur y . 1. KEEP GUARDS IN PLACE AND IN WORKING ORDER. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to see that keys and adjusting ...

  • Kawasaki 840139 - page 4

    This drill press is equipped with a grounded 3-wire power cord with a 3-prong plug. If the power cord will not fit into the wall plug, an approved adapter can be used as long as it is connected to the center screw in the wall plate. See Figure 1 and the steps below to use an AC grounding adapter: 1. Remove the cover plate mounting screw . 2. Insert ...

  • Kawasaki 840139 - page 5

    9. USE ONL Y DRILL BITS, SANDING DRUMS, AND OTHER ACCESSORIES that are designed for the various speeds of this drill press. The drill bits, sanding drums and other accessories should have a shank size 1/2" OR SMALLER. Unsuitable drill bits can break without warning throwing fragments outward at high speeds possibly causing severe injuries. Con ...

  • Kawasaki 840139 - page 6

    30. ADDITIONAL INFORMA TION about the proper use of bench-mounted drill presses is available from the Power T ool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Additionally , you can refer to the Ame ...

  • Kawasaki 840139 - page 7

    FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS: 1. Column Base 2. Column Assembly 3. Column 4. Column Rack 5. T able Crank 6. T able Support 7. T able Crank Assembly 8. T able 9. Vise 10. Vise mtg Hardware 11. Knob (and mtg Hardware) 12. Collar ASSEMBL Y DO NOT connect the power cord to the AC receptacle until the drill press is completely assemble ...

  • Kawasaki 840139 - page 8

    T o minimize crank handle backlash, tighten the support lock, rotate the elevation worm shaft clockwise, assemble the crank tightly against the table support and tighten setscrew. 11.Check column collar for proper adjustment. 12.Collar should not be aligned on the column. 13.Position rack so it will slide freely in the collar when rotated 360 (arou ...

  • Kawasaki 840139 - page 9

    6. Install the setscrews in the holes on the right side of the head assembly . 7. Using a 5mm “L” hex wrench (located in the loose parts box) securely tighten the setscrews. INST ALLING BEL T GUARD KNOB T o av oi d po ssib le in ju ry , alw ay s ke ep the b elt gua rd clo sed du ri ng dri ll pr es s op erat ion . Fa il ur e to do so co uld r es ...

  • Kawasaki 840139 - page 10

    18 17 ADJUSTING THE DRIVE PULLEYS The drive pulleys on the spindle shaft and the motor shaft may loosen during shipment. It is crucial that these pulleys are the same height on their respective shafts. Failure to square these pulleys could result in premature belt wear or damage to the motor and spindle bearings or both. 1. Lay a straightedge acros ...

  • Kawasaki 840139 - page 11

    SQUARING THE WORKT ABLE The combination square must be “true” when used to square the worktable. See T ools Required for Assembly . This is essential in order to do precision drilling. 1. Insert a straight, ground steel rod, approxi- mately 3" long (not included) into the drill check and tighten. 2. Raise the table to working height. 3. Pl ...

  • Kawasaki 840139 - page 12

    DO NOT attempt to perform any drilling operations until the worktable is securely locked in position with the table lock clamp. Failure to lock the worktable could cause it to unexpectedly tilt causing the workpiece to bind on the drill bit. This could cause severe damage to the drill press and severe injur y to operator from pieces of drill bit fl ...

  • Kawasaki 840139 - page 13

    ADJUSTING THE T ABLE HEIGHT T urn the drill press ON/OFF switch to the OFF position and disconnect the AC power to prevent drill press from accidentally turning on. 1. Loosen the table lock handle. 2. T urn the table crank handle count- er -clockwise to lower the work- table and clockwise to raise it. 3. Adjust the worktable to the desired height. ...

  • Kawasaki 840139 - page 14

    SETTING THE DRILLING DEPTH ADJUSTMENT T urn the drill pre ss ON/O FF switc h to t he OFF posit ion a nd dis con nec t the AC powe r to pre ven t dril l pre ss fro m acc ide nta lly turni ng on. The drilling depth adjustment is used when more than one hole is to be drilled to exactly the same depth (i.e. drilling holes for spindles in a handrail). 1 ...

  • Kawasaki 840139 - page 15

    DRILLING THROUGH WOOD: 1. Position the workpiece so that the hole to be drilled is over the center hole on the worktable. 2. Place a piece of scrap material under the workpiece to prevent “splintering” on the bottom side of the workpiece. 3. Clamp BOTH the workpiece and the scrap material to the worktable. 4. Select the proper speed for the wor ...

  • Kawasaki 840139 - page 16

    NEVER LOOK INTO THE LASER BEAM. Any contact with the eyes by the beam could cause injur y . Do not use the laser when cutting reflective materials. DO NOT AIM THE LASER BEAM A T ANYONE OR A T REFLECTIVE SURF ACES. CLASS 2M LASER PRODUCT . Any contact with the eyes by the beam could cause injury . Ensure the laser beam is turned on only when the too ...

  • Kawasaki 840139 - page 17

    TROUBLE PROBABLE CAUSE SOLUTION REPLACING LASER BA TTERIES The laser runs on two AAA batteries which are located beneath the “ON/OFF” switch. When the laser light begins to dim, change both batteries. NEVER mix old batteries with new. TO CHANGE LASER BA TTERIES: 1. Open batter y compartment cover . 2. Make sure batteries are correctly positione ...

  • Kawasaki 840139 - page 18

    SPECIFICA TIONS SPECIFICA TIONS Voltage 120V 60 Hz Rated Current 6.6 A No-Load Speed (motor) 1725 RPM Max. Distance From Spindle Axis T o Sur face Of Column: 6 5/8" (170.275mm) Max. Distance From Spindle End T o Sur face Of T able: 30 3/4" (781.050mm) Spindle T ravel: 3 1/8" (79.375mm) Chuck Capacity 5/8" (15.875mm) Range of Spi ...

  • Kawasaki 840139 - page 19

    item and/or part will be repaired and/or replaced. If the unit is repaired, new or reconditioned replacement parts may be used. If Alltrade chooses to replace the product, it may replace it with a new or reconditioned one of the same or comparable design. The repaired or replaced unit will be warranted under the terms of the remainder of the warran ...

  • Kawasaki 840139 - page 20

    REPRESENT A TIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES. IN NO EVENT , WHETHER AS A RESUL T OF A BREACH OF CONTRACT , WAR R A N TY , T ORT ( I NC L U DI N G NE G L IG E N C E) O R O T HE R W I SE , SH A L L ALL TRADE’S AND/OR ITS REPRESENT A TIVE(S)’ LIABILITY EXCEED THE PRICE OF THE PRODUCT . ANY AND ALL LIABILITY CONNECTED ...

メーカー Kawasaki カテゴリー Drill

Kawasaki 840139のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 840139の取扱説明書
- Kawasakiの製品カード
- パンフレット
- またはKawasaki 840139の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Kawasaki 840139の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Kawasaki 840139の取り付け説明書、サービスマニュアル、簡易説明書、またはKawasaki 840139のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Kawasaki 840139の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Kawasaki 840139デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKawasaki 840139を使用するのを助ける技術的文書のことです。説明書は通常、全てのKawasaki 840139ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Kawasakiの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Kawasaki 840139の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKawasaki 840139の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Kawasaki 840139に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Kawasaki 840139デバイスの基本機能を使うにあたってのヒント。 Kawasaki 840139のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Kawasaki 840139に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKawasaki 840139のメーカー/サービスへの連絡先に関する情報。

Kawasaki 840139についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKawasaki 840139の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKawasaki 840139で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)