Husqvarna YTH26V54の取扱説明書

52ページ 3.93 mb
ダウンロード

ページに移動 of 52

Summary
  • Husqvarna YTH26V54 - page 1

    07002 YTH26V54 Owner's Manual 532 44 11-32 Rev 1 Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty . ...

  • Husqvarna YTH26V54 - page 2

    2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAP ABLE OF AMPUT A TING HANDS AND FEET AND THROW ING OBJECTS. F AIL URE TO OBSERVE THE FOLL OWING SAFETY INSTRUCTIONS COULD RESUL T IN SERIOUS INJURY OR DEA TH. I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the ...

  • Husqvarna YTH26V54 - page 3

    3 SAFETY RULES Safe Operation Practices for Ride-On Mowers • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades ...

  • Husqvarna YTH26V54 - page 4

    4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICA TIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 UNASSEMBLED P ARTS ............................................... 5 ASSEMBL Y ................................................................. ...

  • Husqvarna YTH26V54 - page 5

    5 UNAS SEMBLED P ARTS (5) Large Retainer Springs (1) Small Retainer Springs (5) 1-3/16 O .D. W ashers (2) Rear Lift Link Assemblies (1) F ront Lift Link Assembly (1) Anti- Sway Bar (1) 3/4 O .D. W ashers (1) Small Retainer Springs (1) 1-1/4 O .D. W asher (1) Wheel (1) 3/8-16 Locknut (1) Shoulder Bolt Mower Mower F ront Wheel If Equipped Key s (2) K ...

  • Husqvarna YTH26V54 - page 6

    6 AS SEMBL Y NOTE: Y ou may now roll your tractor off the skid. F ollow the instructions below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of ...

  • Husqvarna YTH26V54 - page 7

    7 AS SEMBL Y TRANSAXLE 02965 FRONT BACK ENGINE Q. DEFLECTOR SHIELD Q Fig. 6 90° END INTEGRA TED WASHER END ANTI-SWA Y BAR (S) TOWARDS TOW ARDS TRANSAXLE MOWER DECK • F rom right side of mower , first insert 90° end of anti-sway bar (S) into hole in transaxle bracket (T), located near left rear tire in front of transaxle. NOTE : Flashlight may b ...

  • Husqvarna YTH26V54 - page 8

    8 AS SEMBL Y 6. A TT ACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS (See Fig. 12) • Position front hole in side suspension arm (A) over pin on outside of tractor chassis and secure with large washer and large retainer spring (B). • Repeat on opposite side of tractor . B D A A. MOWER SIDE SUSPENSION ARMS B. RET AINER SPRING D. RIGHT SIDE REAR MOW ...

  • Husqvarna YTH26V54 - page 9

    9 AS SEMBL Y CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance. • Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be prop- erly leveled. See “TO LEVEL MOWER HOUSING? ...

  • Husqvarna YTH26V54 - page 10

    10 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF FUEL CHOKE MOWER HEIGHT REVER ...

  • Husqvarna YTH26V54 - page 11

    11 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING Y OUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American Na ...

  • Husqvarna YTH26V54 - page 12

    12 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide vision safety mask worn over spectacles. HOW TO ...

  • Husqvarna YTH26V54 - page 13

    13 OPERA TION TO MOVE FORWARD AND BACK WARD (See Fig. 20) The direction and speed of movement is controlled by the forward and reverse drive pedals. • Start tractor and release parking brake. • Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed. Fig. 22 TO ADJU ...

  • Husqvarna YTH26V54 - page 14

    14 Fig. 23 OPERA TION Fig. 24 TO TRANSPORT (See Figs. 16 and 24) When pushing or towing your tractor , be sure to disengage transmission by placing freewheel control in free wheel ing po- si tion. Free wheel control is located at the rear drawbar of tractor . • Raise attachment lift to highest position with at tach ment lift control. • Pull fre ...

  • Husqvarna YTH26V54 - page 15

    15 OPERA TION CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. IMPORT ANT : WHEN OPERA TING IN TEMPERA TURES BEL OW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GAS O LINE TO HELP ENSURE GOOD COLD WEA THER ST ART ING. CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can att ...

  • Husqvarna YTH26V54 - page 16

    16 OPERA TION PURGE TRANSMISSION CAUTION: Never engage or disengage freewheel lever while the engine is run ning. T o ensure proper operation and performance, it is rec om - mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de vel - ...

  • Husqvarna YTH26V54 - page 17

    17 MAINTENANCE T R A C T 0 R 1 - Change more often when operating under a heavy load or in high ambient temperatures . 2 - Service more often when operating in dir ty or dusty conditions. E N G I N E 3 2 2 2 2 3 - Replace blades more often when mowing in sandy soil. 4 - Not required if equipped with maintenance-free battery . 5 - See Cleaning in Ma ...

  • Husqvarna YTH26V54 - page 18

    18 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE” in the Ser vice and Ad just ments section of th ...

  • Husqvarna YTH26V54 - page 19

    19 MAINTENANCE ENGINE LUBRICA TION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather , they will result in increased oil consumption when used ...

  • Husqvarna YTH26V54 - page 20

    20 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PROD UCT SPECIFICA TIONS? ...

  • Husqvarna YTH26V54 - page 21

    21 SERVICE AND ADJUSTMENTS WARNING: TO A VOID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP ” and remove key . • Make sure the blades and all moving parts have completely stopped. ? ...

  • Husqvarna YTH26V54 - page 22

    22 SERVICE AND ADJUSTMENTS FRONT - TO-BACK ADJUSTMENT (See Figs. 36 & 37) IMPORT ANT : Deck must be level side-to-side. T o obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position. CAUTION: Blades are sharp. Protect your ha ...

  • Husqvarna YTH26V54 - page 23

    23 SERVICE AND ADJUSTMENTS Fig. 38 TO REPL ACE MOTION DRIVE BEL T (See Fig. 38) P ark the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest. BEL T REMOV AL - • Remove mower (See “TO REMOVE MOWER” section in this manual). NOTE: Observe entire motion drive ...

  • Husqvarna YTH26V54 - page 24

    24 SERVICE AND ADJUSTMENTS TO ST ART ENGINE WITH A WEAK BA TTERY (See Fig. 40) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BA TTER ...

  • Husqvarna YTH26V54 - page 25

    25 SERVICE AND ADJUSTMENTS TO REPL ACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERL OCKS AND REL A YS Loose or damaged wiring may cause your tractor to run poorly , sto ...

  • Husqvarna YTH26V54 - page 26

    26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from t ...

  • Husqvarna YTH26V54 - page 27

    27 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter . 5. Clean/replace air fil ...

  • Husqvarna YTH26V54 - page 28

    28 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. Faulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. Worn, bent or loose blade. 1. Re ...

  • Husqvarna YTH26V54 - page 29

    29 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 SCHEMA TIC NO TES M FUSE ST ARTER SOLENOID BA TTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PEDAL UP) REVERSE SWITCH (NOT IN REVERSE) SEA T SWITCH (NOT OCCUPIED) SHORTING CONNECTOR CHASSIS HARNESS IGNITION UNIT HOUR METER REGULA TOR CHASSIS HARNESS CONNECTOR (MA TING SIDE) DASH HAR ...

  • Husqvarna YTH26V54 - page 30

    30 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 ELECTRICAL 8 1 99 100 91 2 27 90 28 55 26 43 41 24 27 25 30 33 22 79 21 40 71 34 With Service Minder Option 46 46 With 12V Outlet Option 59 103 16 42 T11S 102 29 105 ...

  • Husqvarna YTH26V54 - page 31

    31 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 41 41-25 Box Battery 16 532 17 61-38 Switch Interlock Push-In 21 532 40 02-52 Harness Socket Light w/4152J 22 532 00 41-52 Bulb Light 24 532 40 02-53 Cable Ba ...

  • Husqvarna YTH26V54 - page 32

    32 52 217 189 189 152 68 68 213 218 228 228 194 180 58 189 189 233 233 182 68 68 176 176 175 165 183 236 150 34 130 130 177 235 195 176 37 194 194 162 282 282 36 36 285 286 283 199 284 287 14 130 130 202 203 208 18 15 25 207 5 176 176 205 151 206 137 137 214 204 161 297 191 178 Chassis-tex_GT HUSQ_I I_41 TRACTOR - - MODEL NUMBER YTH26V54 (960430132 ...

  • Husqvarna YTH26V54 - page 33

    33 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 CHASSIS KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 3 532 43 97-52 Applique Subasm. 5 532 43 74-71 Dash 14 532 44 11-77 Hood 15 532 43 97-33 Lens LH 18 532 43 77-62 Grille 25 532 43 9 ...

  • Husqvarna YTH26V54 - page 34

    34 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 DRIVE 231 51 170 225 125 drive-tex_K46_pedal_39_r1 2 2 73 73 33 205 1 116 33 230 230 183 183 205 116 64 188 161 35 184 167 160 42 29 15 159 159 221 186 189 49 187 50 51 52 51 190 185 125 226 227 125 80 125 208 210 214 125 215 153 166 211 211 222 17 163 153 99 216 143 185 ...

  • Husqvarna YTH26V54 - page 35

    35 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 - - - - - - - - - - T ransaxle, TUFFTORQ K46 2 532 12 35-83 K ey 15 819 13 13-16 W asher 13/32 x 13/16 x 16 Ga. 17 532 41 36-78 Spring, Brake 26 532 19 96-79 Spring Return Cruise 29 532 40 38-06 Rod, ...

  • Husqvarna YTH26V54 - page 36

    36 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 ENGINE 1 84 12 11 41 42 85 29 SP ARK ARRESTER KIT 84 45 18 15 37 28 37 21 20 engine-te x_bs-2cyl_47_r1 81 82 9 90 62 71 70 79 69 87 2 91 ...

  • Husqvarna YTH26V54 - page 37

    37 KEY P ART NO . NO . DESCRIPTION 1 - - - - - - Engine Briggs & Stratton Model No. 44P777-1553-G1 2 532 14 97-23 Muffler 9 532 19 43-20 K eeper Belt Engine 11 532 40 00-08 Clutch 12 532 40 50-97 Pulley Engine 15 532 41 41-51 T ank F uel 18 532 43 92-08 Cap Asm F uel 20 532 42 35-02 Control Throttle/Choke 21 532 41 63-58 Screw #10 x .750 BOS Th ...

  • Husqvarna YTH26V54 - page 38

    38 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 STEERING ASSEMBL Y steering-tex_HUSQHR_4 6 5 13 13 53 8 9 8 7 9 8 7 62 4 70 68 69 67 67 66 15 15 14 14 61 2 6 35 59 58 16 28 13 22 64 21 51 26 1 45 19 60 63 57 63 ...

  • Husqvarna YTH26V54 - page 39

    39 KEY P ART NO . NO . DESCRIPTION 1 532 43 97-40 Wheel, Steering 2 532 19 59-68 Axle Asm., Front 4 532 40 30-87 Spindle Asm., LH 5 532 40 30-88 Spindle Asm., RH 6 532 12 49-31 Bearing, Race Thrust Harden 7 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga. 8 812 00 00-29 Ring, Klip #T5304-75 9 532 12 12-32 Cap, Spindle 13 532 12 17-49 Washer 25/32 x 1-1/4 ...

  • Husqvarna YTH26V54 - page 40

    40 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 SEA T AS SEMBL Y 1 532 42 40-68 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock W/Ins. 3/8-16 unc 7 532 12 41-81 Spring, Seat Cprsn 8 532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems 10 532 19 69-77 Pan, Seat 21 532 17 18-52 Bo ...

  • Husqvarna YTH26V54 - page 41

    41 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 lift-te x_23 91 89 87 89 87 91 2 532 42 20-27 Shaft Asm., Lift 3 532 19 52-31 Lever Lift Handle 7 532 41 15-55 Grip, Lever 10 532 19 63-14 Spring T orsion 87 532 19 42-09 Pin Cotter 7/16 Bow Tie Lock 88 532 41 07-10 Spring Lift ...

  • Husqvarna YTH26V54 - page 42

    42 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 MOWER DECK MOWER?DECKªTEX??R                                 ...

  • Husqvarna YTH26V54 - page 43

    43 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 MOWER DECK KEY P ART NO . NO. DESCRIPTION KEY P ART NO . NO. DESCRIPTION NOTE : All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 44 15-47 Deck Weldment Mower 6 532 19 60-66 Cover Mandrel LH 7 532 19 71-81 Cover Mandrel RH 8 532 19 30-03 Bolt 7/16 Asm. ...

  • Husqvarna YTH26V54 - page 44

    44 TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO . 960 43 01-32 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY P ART NO . NO . DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 05 91-92 Cap V alve Tire 2 532 06 51- ...

  • Husqvarna YTH26V54 - page 45

    45 &RQVXPHU:KHHOHG3URGXFWV ±/LPLWHG:DUUDQW +XVTYDUQD ZDUUDQWV WR WKH RULJLQDO UHWDLO SXUFKDVHU WKDW WKLV + XVTYDUQD SURGXFW LV IUHH IURP GHIHFWVLQ PDWHULDO RU ZRUNPDQVKLS XQGHU QRUPDO XVH DQG PDLQWHQDQ FHIURP WKH GDWH RI UHWDLO SXUFKD VH? ...

  • Husqvarna YTH26V54 - page 46

    46 F 3UHYHQWDWLYHPDLQWHQDQ FHDVRXWOLQHGLQWKH RSHUDWRU¶VPDQXDO  ,Q DGGLWLRQ RX PXVW FHDVH XVLQJ WKH SURGXFW LPPHGLDWHO XSRQ DQ IDLOXUH RU GDPDJH 7KH SURGXFW VKRXOG EH WDNHQ WR DQ DXWKRU L]HG +XVTYDUQDVHUYLFLQJGHDOHUSULRUWRDQIX ...

  • Husqvarna YTH26V54 - page 47

    47 &RQVXPHU:KHHOHG:DUUDQW &KDUW ([KLELW$ &RQVXPHU SHUVRQDO KRXVHKROGXVHRQO &RPPHUFLDO DQFRPPHUFLDO SURIHVVLRQDOLQVWLWXWLRQDO DULJFXOXWUDORULQFRPHSURGXFLQJ XVHRWKHUWKDQ5HQWDO8VH 5HQWDO DQUHQWDO XVDJH 5LGLQJ/DZQ? ...

  • Husqvarna YTH26V54 - page 48

    48 &RQVXPHU:KHHOHG:DUUDQW &KDUW ([KLELW$ &RQVXPHU SHUVRQDO KRXVHKROGXVHRQO &RPPHUFLDO DQFRPPHUFLDO SURIHVVLRQDOLQVWLWXWLRQDO DULJFXOXWUDORULQFRPHSURGXFLQJ XVHRWKHUWKDQ5HQWDO8VH 5HQWDO DQUHQWDO XVDJH 3URGXFW& ...

  • Husqvarna YTH26V54 - page 49

    49 SERVICE NOTES ...

  • Husqvarna YTH26V54 - page 50

    50 SERVICE NOTES ...

  • Husqvarna YTH26V54 - page 51

    51 1 5 DE G REE S M AX . FOLD ALON G DOTTED LINE THI S I S A 1 5 DE G REE S LOPE ONLY RIDE UP AND DO W N HILL, NOT ACRO SS HILL S U GG E S TED G UIDE FOR S I G HTIN G S LOPE S FOR S AFE OPERATION W ARNIN G : To avo i d s er i o us i n ju ry, operate yo u r tra c tor u p and do w n the fa c e of s lope s , never a c ro ss the fa c e . Do not mo w s ...

  • Husqvarna YTH26V54 - page 52

    12.14.10 BAD Printed in the U.S.A. ...

メーカー Husqvarna カテゴリー Lawn Mower

Husqvarna YTH26V54のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- YTH26V54の取扱説明書
- Husqvarnaの製品カード
- パンフレット
- またはHusqvarna YTH26V54の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Husqvarna YTH26V54の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Husqvarna YTH26V54の取り付け説明書、サービスマニュアル、簡易説明書、またはHusqvarna YTH26V54のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Husqvarna YTH26V54の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Husqvarna YTH26V54デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHusqvarna YTH26V54を使用するのを助ける技術的文書のことです。説明書は通常、全てのHusqvarna YTH26V54ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Husqvarnaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Husqvarna YTH26V54の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHusqvarna YTH26V54の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Husqvarna YTH26V54に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Husqvarna YTH26V54デバイスの基本機能を使うにあたってのヒント。 Husqvarna YTH26V54のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Husqvarna YTH26V54に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHusqvarna YTH26V54のメーカー/サービスへの連絡先に関する情報。

Husqvarna YTH26V54についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHusqvarna YTH26V54の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna YTH26V54で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)