Grizzly G1014ZXの取扱説明書

30ページ 1.9 mb
ダウンロード

ページに移動 of 30

Summary
  • Grizzly G1014ZX - page 1

    COPYRIGHT © MARCH, 2008 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BL10589 PRINTED IN TAIWAN Wh at Ch an ge d? W e ha ve added a sleev e guard to the sander to help reduce the risk of entanglement. The sleev e guard M UST be install ...

  • Grizzly G1014ZX - page 2

    In tr od uc ti on The Mod el G 1 01 4ZX is t he same sander as the Model G 1 0 1 4Z with t he addition of the c abinet stand. Please use the includ ed G 1 0 1 4Z manual for refe rence and for ordering par ts that are not listed o n the back of t his inser t. As se mb ly 1. Insert 5 ⁄ 16 -18 x 1" hex bolts into each of the rubber feet. 2. Sec ...

  • Grizzly G1014ZX - page 3

                                G1014ZX Replacement Parts NOTICE All parts for the Model G1014ZX, except those shown above, are the same as the Model G1014Z. Therefore, please use ...

  • Grizzly G1014ZX - page 4

    COMBINATION SANDER MODEL G1014Z INSTRUCTION MANUAL COPYRIGHT © 1992 BY GRIZZLY INDUSTRIAL, INC. REG.# TX 3 360 514 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. REVISED APRIL, 1997. PRINTED IN USA ...

  • Grizzly G1014ZX - page 5

    ...

  • Grizzly G1014ZX - page 6

    G1014Z Combination Sander -1- Table Of Contents PAGE 1. SAFETY ....................................................................................................................2 SAFETY RULES FOR ALL TOOLS ....................................................................2 ADDITIONAL SAFETY INSTRUCTIONS FOR SANDERS ............................. ...

  • Grizzly G1014ZX - page 7

    -2- G1014Z Combination Sander WARNING: For Your Own Safety Read Instruction Manual Before Operating Sander Safety Instructions For Power Tools These safety rules cannot cover every situation in a work shop. Consider your conditions when setting up or operating your jointer. SECTION 1: SAFETY a) Always wear eye protection. b) When belt sanding, supp ...

  • Grizzly G1014ZX - page 8

    G1014Z Combination Sander -3- Additional Safety Instructions For Sanders 17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommend- ed accessories. The use of improper acces- sories may cause risk of injury to persons. 18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefull ...

  • Grizzly G1014ZX - page 9

    -4- G1014Z Combination Sander Figure 1. Grounded Outlet Box Current Carrying Prongs Grounding Blade Is Longest Of the Three Blades Under no circumstances should the grounding pin from any three-pronged plug be removed. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Check with a qualified electrician or o ...

  • Grizzly G1014ZX - page 10

    G1014Z Combination Sander -5- We are proud to bring you the Model G1014Z Combination Sander. The Model G1014Z is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer s ...

  • Grizzly G1014ZX - page 11

    -6- G1014Z Combination Sander Contents of the Bolt Bag QTY. DESCRIPTION LOCATION 16 5 ⁄ 16 ''-18 x 1 ⁄ 2 '' Carriage Bolts Stand 16 5 ⁄ 16 '' Flat Washers Stand 16 5 ⁄ 16 ''-18 Hex Nuts Stand 4 5 ⁄ 16 ''-18 x 1 ⁄ 2 '' Hex Bolts Stand/Base 4 5 ⁄ 16 '' Flat Washers St ...

  • Grizzly G1014ZX - page 12

    G1014Z Combination Sander -7- Clean up The work table and other unpainted parts of the Model G1014Z are coated with a waxy oil that protects them from corrosion during shipment. Remove the protective coating with mineral spir- its and cloth rags. Do not use gasoline or other petroleum based solvents because of their extremely low flash points. Do n ...

  • Grizzly G1014ZX - page 13

    -8- G1014Z Combination Sander Order Of Assembly SECTION 4: ASSEMBLY Most of your Combination Sander has been assembled at the factory. The few remaining pieces will go together quickly and should be done in the following order: 1. Stand 2. Mounting Sanding Unit 3. Attaching the Back Stop 4. Attaching Sanding Disc 5. Mounting the Work Table Note: Al ...

  • Grizzly G1014ZX - page 14

    Figure 3. G1014Z Combination Sander -9- Figure 4. 3. Bolt the shorter upper and lower braces to one of the 2 stand sub-assemblies. Figure 4. 4. Now attach the other sub-assembly to the ends of the short braces. Tighten down all the stand bolts at this time. Figure 5. Figure 5. 2. Attach the longer upper and lower cross braces to 2 of the stand legs ...

  • Grizzly G1014ZX - page 15

    -10- G1014Z Combination Sander Figure 7. 5. At this point, install the back stop, using the Hex Bolt and Washer as shown in Figure 7. Figure 8. 4. Install the Sanding Disc as shown in Figure 7. Make sure the Setscrew is lined up on the flat spot on the drive shaft. Figure 6. Sanding Unit 1. Set the Sanding Unit on the Stand, carefully aligning the ...

  • Grizzly G1014ZX - page 16

    G1014Z Combination Sander -11- Figure 9. Figure 10. 6. Now install the Dust Port using the Hex Bolts and Washers as shown in Figure 9. 7. The last step involves mounting the working table. Loosen the two setscrews in the cast iron base. Insert the table support rod into its hole, making sure the flat portion of the shaft is facing the setscrews. Ti ...

  • Grizzly G1014ZX - page 17

    -12- G1014Z Combination Sander 2. Turn the knob approximately 1 ⁄ 4 turn clock- wise to move the belt towards the tracking knob, counter-clockwise to move the belt away. 3. Turn the machine on and off again quickly to see if the tracking has improved. If not, repeat step 1. If tracking is improved move to step 4. 4. Now with the sander running, a ...

  • Grizzly G1014ZX - page 18

    G1014Z Combination Sander -13- 3. Tighten hex bolt, PN # 91 and run the sander to adjust the tracking if necessary. 4. Try aggressively sanding a piece of scrap wood. If the tracking is not significantly affected and the belt does not slip on the drum, your belt tension is correct. Belt Tensioning Correct belt tension will insure that your sander f ...

  • Grizzly G1014ZX - page 19

    -14- G1014Z Combination Sander Figure 18. Setup for vertical sanding. 2. The Sanding Disc Table can also be moved to become a work table for belt sanding. Simply remove the Table Support Shaft from the base and insert it into the mounting bracket behind the motor. The Bracket’s location is shown in Figure 17. Vertical Positioning The 6" belt ...

  • Grizzly G1014ZX - page 20

    G1014Z Combination Sander -15- Figure 19. Changing Discs To replace the sanding disc: 1. Remove the Working Table. 2. Remove the Cover Knob and open the Cover Door. 3. Peel off the old Sanding Disc. Remove the backing from the new Disc, center it and press it firmly into place. 4. It may become necessary to remove the Cast Iron Disc from the Motor ...

  • Grizzly G1014ZX - page 21

    -16- G1014Z Combination Sander Horizontal Sanding 1. Turn the sander on and allow the belt to reach full speed. 2. Place the workpiece flat on the belt. Be sure to hold the work securely with both hands. Place one hand at the end of the workpiece to feed it against the rotation of the belt, and one hand lightly on top of the piece to ensure adequat ...

  • Grizzly G1014ZX - page 22

    G1014Z Combination Sander -17- Curved Sanding To sand curves, use the end of the belt arm. Hold the workpiece firmly and apply light, even pres- sure to the belt. To avoid excessive loading of the belt in one area, move workpiece slowly across entire surface of belt. Figure 21. Figure 21. Disc Sanding 1. Loosen table lock knob and tilt work table t ...

  • Grizzly G1014ZX - page 23

    -18- G1014Z Combination Sander SECTION 7: MAINTENANCE Lubrication V- Belt Your combination sander is equipped with shield- ed and pre-lubricated ball bearings and require no lubrication for the life of the bearings. All bear- ings are common sizes and are readily available from a local bearing supply house or our Service Department. Without proper ...

  • Grizzly G1014ZX - page 24

    G1014Z Combination Sander -19- The following pages contain general machine specifications, parts diagram and list and Warranty/Return information for your Model G1014Z Combination Sander. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Our trained service ...

  • Grizzly G1014ZX - page 25

    -20- G1014Z Combination Sander Machine Data GRIZZLY MODEL G1014Z COMBINATION SANDER Design Type .......................................................................................................................... Floor Model Overall Dimensions and Specifications: Base ........................................................................... ...

  • Grizzly G1014ZX - page 26

    1 2 94 98 99 86A 100 107 108 3 5 96 96 95 12 11 4 6 13 9 8 39 103 15 7 A 2 2 3 3 59 62A 106 89 62A 116 115 114 64 105 105 82A 85A 102 81A 83A 101 87A 88A 84A 92 91 B B 106 89 G1014Z Combination Sander -21- ...

  • Grizzly G1014ZX - page 27

    70 43 77 57 56 49 27 50 97 12 71 53A 90 41 41 13 A 37 80 52 25 69 27 28 20 29 33 33 31 31 25 25 26 26 27 13 32 24 97 14 28 10 10 44 23 30 10 19 42 10 21 22 34 35 97 32 32 42 36 97 40 93 18 -22- G1014Z Combination Sander ...

  • Grizzly G1014ZX - page 28

    G1014Z Combination Sander -23- 32 112 104 110 111 113 109 12 13 65 65 65 12 13 58 41 13 13 12 12 13 12 13 ...

  • Grizzly G1014ZX - page 29

    REF PART # DESCRIPTION REF PART # DESCRIPTION -24- G1014Z Combination Sander 57 P1014057 SUPPORT 5 ⁄ 8 ''-11 x 9'' 58 P1014058 FOOT 59 P1014059 IDLER ROLLER SHAFT 62B P1014062B ROLLER ADJ BAR 64 P1014064 IDLER ROLLER 65 PCB05 CARRIAGE BOLT 5 ⁄ 16 -18 x 3 ⁄ 4 '' 69 P1014069 MITER BODY 70 P1014070 SCALE 71 P1014071 ...

  • Grizzly G1014ZX - page 30

    G1014Z Combination Sander -25- Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole writte ...

メーカー Grizzly カテゴリー TV VCR Combo

Grizzly G1014ZXのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- G1014ZXの取扱説明書
- Grizzlyの製品カード
- パンフレット
- またはGrizzly G1014ZXの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Grizzly G1014ZXの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Grizzly G1014ZXの取り付け説明書、サービスマニュアル、簡易説明書、またはGrizzly G1014ZXのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Grizzly G1014ZXの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Grizzly G1014ZXデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGrizzly G1014ZXを使用するのを助ける技術的文書のことです。説明書は通常、全てのGrizzly G1014ZXユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Grizzlyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Grizzly G1014ZXの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGrizzly G1014ZXの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Grizzly G1014ZXに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Grizzly G1014ZXデバイスの基本機能を使うにあたってのヒント。 Grizzly G1014ZXのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Grizzly G1014ZXに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGrizzly G1014ZXのメーカー/サービスへの連絡先に関する情報。

Grizzly G1014ZXについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGrizzly G1014ZXの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGrizzly G1014ZXで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)