Dixon 539130212の取扱説明書

27ページ 0.82 mb
ダウンロード

ページに移動 of 27

Summary
  • Dixon 539130212 - page 1

    Operators Manual 539 13021 1 - DCKC 539 130212 - DCRC Models: Please read these instructions carefully and make sure you understand them before using the machine. MANUAL NO. 539 130679 REV IR (02/06/07) Part s Manual Collection System ...

  • Dixon 539130212 - page 2

    4 W ARNING: Engine exhaust, some of its constituent s, and certain vehicle component s con- t ain or emit chemicals known to the St ate of California to cause cancer and birth defects or other reproductive harm. INDEX Operators Guide General Information ................................................................. 5 Safety Procedures .......... ...

  • Dixon 539130212 - page 3

    5 SAFETY RULES Safety Procedures 1 - T raining: • Read the Operator ’s manual. If the operator(s) or mechanic(s) can not read English it is the owner ’s responsibility to explain this material to them. • Become familiar with the safe operation of the equipment, operator ’s controls, and safety signs. • All operators and mechanics should ...

  • Dixon 539130212 - page 4

    6 SAFETY RULES 3 - Operation • Never run an engine in an enclosed area. • Only operate in good light, keeping away from holes and hidden hazards. • Slow down and use extra care on hillsides. Make turns gradually and at slow speed. Do not operate across the sides of slopes. Operate up and down slopes only . Do not operate on steep slopes. • ...

  • Dixon 539130212 - page 5

    7 ASSEMBL Y Assembly Instructions T ools Required: Ratchet T orque Wrench 1/2" W rench 1/2" Socket 9/16" W rench 9/16" Socket (2) 3/4" Wrench 3/4" Socket Flat Screw Driver (2) 1” Wrench - open end RAM/RAM MAG 1. Remove clamshell from crate. 2. Remove two 5/16 x 3/4 carriage bolts from the lower flange of the rear gua ...

  • Dixon 539130212 - page 6

    8 ASSEMBL Y 10. Lift Clamshell assembly onto (539 1 14781) Mount Bracket, Lower . Position tubes on bottom of clamshell on out side of the tubes on (539 1 14781) Mount Bracket, Lower . 1 1 . Secure with (539 1 19372) Hinge Pin and (539 1 15501) Cotter Pin. 12. Hook both (539 1 14783) Linkage, Support into (539 1 14786) Plate, Support, Linkage and s ...

  • Dixon 539130212 - page 7

    9 ASSEMBL Y FIGURE 3 KODIAK 1. Remove clamshell from crate. 2. Remove two 5/16 x 3/4 carriage bolts from the lower flange of the rear guard on the mower . 3. Place (539 1 14815) Mount Bracket, Lower in place and secure using four (539 1 1 1785) 3/8 x 3/4 carriage bolts, four (539 976979) 3/ 8 nyloc hex nut and two (539 107271) 5/16 x 1 carriage bol ...

  • Dixon 539130212 - page 8

    10 ASSEMBL Y 5. Attach two (539 1 14812) Linkage, Support to the clamshell assembly as shown in Fig- ure 6. 6. Secure with two (539 100476) 5/8 hex jam nut and two (539 1 15591) 5/8 nyloc hex nut as shown. Do not tighten nuts. 7. Lift Clamshell assembly onto (539 1 14815) Mount Bracket, Lower . Position tubes on bottom of clamshell on out side of t ...

  • Dixon 539130212 - page 9

    11 ASSEMBL Y FRONT WEIGHTS - RAM 1. Bolt cast weight and two weight brackets to- gether using four bolts (539 106492, 3/8 x 2 3/4”) and four nuts (539 976979, 3/8” nyloc). 2. Slide both weight brackets over the front tube on the frame. Be sure to position in the cen- ter of the frame. 3. Secure with four bolts (539 991 126, 3/8 x 3 3/4”) and ...

  • Dixon 539130212 - page 10

    12 ASSEMBL Y FRONT WEIGHTS - KODIAK CAST COUNTERWEIGHT WEIGHT BAR HOLD DOWN FRONT WEIGHT BAR 1. Remove mower foot plate and floor pan. 2. Align weight bar to the front of the frame. See diagram. 3. Secure weight bar to mower frame with four 5/16-18 x 1 1/4” hex bolts from kit, reuse the four 5-16” washers and four 5/16” nyloc nuts that were r ...

  • Dixon 539130212 - page 11

    13 OPERA TION Operating the Collection System 1. NEVER USE THE COLLECTION SYSTEM WITHOUT THE BLOWER ASSEMBL Y AND HOSES SECUREL Y A TT ACHED. 2 . Make sure hoses are connected at both ends. Inspect hoses prior to each use. 3. Do not use the unit on slopes greater than 10 degrees. 4 . The mower must be running in order to vacuum debris through the m ...

  • Dixon 539130212 - page 12

    14 SER VICE AND MAINTENANCE Prevent ative Maintenance Schedule Item Before Every Every Every Each Use 5 Hours 25 Hours 50 Hours Inspect/Clean Poly Mesh X X Check/T ighten Nuts & Bolt s X Check/T ighten Hoses X T urn Hose End to End X Rotate Hose X Clean Machine X W ARNING The collection system must be completely empty or removed while driving f ...

  • Dixon 539130212 - page 13

    15 SER VICE AND MAINTENANCE Caring For Hoses 1. Inspect hoses before each use. If hoses have excessive wear , tears, or punctures, replace immediately . 2. T o prolong the life of the hose, periodically ro- tate hose and turn hose end to end. Refer to Preventative Maintenance Schedule in this manual. 3. Avoid twist s and sharp turns in the hoses, a ...

  • Dixon 539130212 - page 14

    16 SERVICE AND MAINTENANCE PROBLEM POSSIBLE CAUSE CORRECTION Loss of V acuum. 1. Hose or hood inlet clogged. 1. Remove hose and clean inlet. 2. Container full. 2. Inspect and empty . 3. Poly mesh plugged. 3. Clean poly mesh. Unusual vibration 1. Solid object jammed in unit. 1. Check and remove any or noise. obstruction. 2. Loose or missing bolts on ...

  • Dixon 539130212 - page 15

    17 P ARTS ILLUSTRA TIONS ...

  • Dixon 539130212 - page 16

    18 CLAMSHELL ASSEMBL Y 1 2 3 4 5 6 7 8 9 10 REF . REF . 3 ...

  • Dixon 539130212 - page 17

    19 CLAMSHELL ASSEMBL Y 1 .. 539 990629 ... 2 ... HCS 3/8-16 X 2 1/4, GR5 2 .. 539 200282 ... 2 ... NUT , 3/8-16, HAM, NYLOC 3 .. 539 990122 ... 3 ... WASHER, 3/8, SAE 4 ... 539 1 15972 ... 2 ... BUSHING 5 .. 539 990717 ... 1 ... NUT , 5/16-18, NYLOC 6 ... 539 1 19414 ... 1 ... BUSHING , PLASTIC 7 ... 539 1 17244 ... 1 ... ROD END 8 ... 539 1 15609 ...

  • Dixon 539130212 - page 18

    20 CLAMSHELL REAR ASSEMBL Y 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 18 10 10 18 10 12 ...

  • Dixon 539130212 - page 19

    21 CLAMSHELL REAR ASSEMBL Y 1 ... 539 1 17967 ... 1 ... REAR FRAME 2 ... 539 1 19396 ... 2 ... STRAP 3 ... 539 1 19367 ... 1 ... HOOK LA TCH 4 ... 539 1 19377 ... 1 ... CLAMSHELL BACK 5 ... 539 1 19458 ... 1 ... STRAP 6 ... 539 1 17543 ... 1 ... CHAMSHELL VENT 7 ... 539 1 15677 ... 2 ... CLIP NUT , 5/16-18 8 ... 539 1 19412 ... 1 ... VENT SCHREEN 9 ...

  • Dixon 539130212 - page 20

    22 CLAMSHELL FRONT ASSEMBL Y 1 2 3 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 21 25 26 27 28 24 25 20 15 19 18 23 18 23 18 18 23 16 ...

  • Dixon 539130212 - page 21

    23 CLAMSHELL FRONT ASSEMBL Y 1 ... 539 1 19410 ... 1 ... FRONT FRAME 2 ... 539 1 19409 ... 2 ... STRAP 3 ... 539 1 19368 ... 2 ... STRAP 4 ... 539 1 17986 ... 1 ... LIFT SHAFT 5 ... 539 1 19376 ... 1 ... CLAMSHELL, FRONT 6 ... 539 1 15596 ... 2 ... CLEVIS PIN, 5/16 7 ... 539 1 15489 ... 2 ... RET AINING RING 8 ... 539 1 19433 ... 1 ... DEFLECTOR 9 ...

  • Dixon 539130212 - page 22

    24 CLAMSHELL LINKAGE - RAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 5 10 ...

  • Dixon 539130212 - page 23

    25 CLAMSHELL LINKAGE - RAM 1 ... 539 1 16443 ... 1 ... BAR SLEEVE 2 ... 539 1 19372 ... 1 ... HINGE PIN 3 ... 539 1 14781 ... 1 ... BRACKET , MOUNT , LOWER 4 ... 539 1 14783 ... 2 ... LINKAGE, SUPPORT 5 ... 539 1 15501 ... 3 ... HAIR PIN COTTER, 1/8 DIA. X 1 3/4 6 ... 539 1 14786 ... 1 ... BRACKET , SUPPORT , LINKAGE 7 ... 539 1 14824 ... 1 ... LIN ...

  • Dixon 539130212 - page 24

    26 CLAMSHELL LINKAGE - KODIAK 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 18 19 11 6 3 10 ...

  • Dixon 539130212 - page 25

    27 CLAMSHELL LINKAGE - KODIAK 1 ... 539 1 16443 ... 1 ... BAR SLEEVE 2 ... 539 1 19372 ... 1 ... HINGE PIN 3 ... 539 1 15501 ... 3 ... HAIR PIN COTTER, 1/8 DIA. X 1 3/4 4 ... 539 1 14816 ... 1 ... LINKAGE, LA TCH 5 .. 539 990188 ... 1 ... W ASHER, 5/16, SAE 6 .. 539 990717 ... 3 ... NUT , 5/16-18, NYLOC 7 ... 539 1 10340 ... 1 ... NUT , 5/8-1 1C, N ...

  • Dixon 539130212 - page 26

    WEIGHT KIT - RAM 1 ... 539 1 1 1587 ... 1 ... CAST WEIGHT 2 ... 539 1 14898 ... 2 ... BRACKET , WEIGHT 3 .. 539 106492 ... 4 ... HCS, 3/8-16 X 2 3/4, GR5 4 ... 539 991 126 ... 4 ... HCS, 3/8-16 X 3 3/4, GR5 5 .. 539 976979 ... 8 ... NUT , 3/8-16, NYLOC ITEM P ART NO. QTY . DESCRIPTION 1 2 3 4 5 5 4 ...

  • Dixon 539130212 - page 27

    WEIGHT KIT - KODIAK 1 ... 539 1 1 1313 ... 1 ... HOLD DOWN, WEIGHT BAR 2 .. 539 102049 ... 2 ... CLEVIS PIN 3 .. 539 108096 ... 2 ... SPRING RET AINER 4 ... 539 1 14858 ... 1 ... WEIGHT BAR 5 .. 539 990627 ... 4 ... HCS, 5/16-18 X 1 1/4, GR5 6 .. 539 977778 ... 1 ... ABRASIVE P AD 7 .. 539 102587 ... 3 ... GROMMET , BUMPER 8 .. 539 000019 ... 3 ... ...

メーカー Dixon カテゴリー Lawn Mower Accessory

Dixon 539130212のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 539130212の取扱説明書
- Dixonの製品カード
- パンフレット
- またはDixon 539130212の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Dixon 539130212の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Dixon 539130212の取り付け説明書、サービスマニュアル、簡易説明書、またはDixon 539130212のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Dixon 539130212の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Dixon 539130212デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDixon 539130212を使用するのを助ける技術的文書のことです。説明書は通常、全てのDixon 539130212ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Dixonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Dixon 539130212の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDixon 539130212の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Dixon 539130212に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Dixon 539130212デバイスの基本機能を使うにあたってのヒント。 Dixon 539130212のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Dixon 539130212に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDixon 539130212のメーカー/サービスへの連絡先に関する情報。

Dixon 539130212についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDixon 539130212の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDixon 539130212で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)