-
Lennox Hearth SWS210 - page 1
INST ALLA TION AND OPERA TION MANUAL W ARNINGS • Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will retain heat for a while after shutting off the appliance. Severe burns may result. • Carefully supervise children in the same room as appliance. Save These Instructions For Future Reference A F ren c ...
-
Lennox Hearth SWS210 - page 2
2 USING THIS MANUAL Please read and carefully follow all of the instructions found in this manual. Please pay special attention to the safety instructions provided in this manual. PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE CONGRA TULA TIONS! When you purchased your new wood stove, you joined the ranks of thousands of individuals whose answer to th ...
-
Lennox Hearth SWS210 - page 3
3 IM PO R T AN T S AF ET Y A ND W ARN II NG IN FO RM A TI O N REA D TH IS MA NU AL IN I TS EN TI RE TY AN D UN DER - ST AND T HES E RU LES T O FO LLO W FO R S AF ET Y . 1. When this room heater is not properly installed, a house fire may result. T o reduce the risk of fire, follow the instal- lation instructions. Contact local building or fire o ...
-
Lennox Hearth SWS210 - page 4
4 This manual describes the installation and operation of these non-catalytic wood heaters. These heaters meet the U.S. Environmental Protection Agency’ s emissions limits for wood heaters sold on or after July 1, 1990. This heater has been developed, tested and constructed in accordance with the requirements of UL 1482, ULC S627 and HUD standard ...
-
Lennox Hearth SWS210 - page 5
5 This appliance is not designed to be operated in a negative pressure. In very airtight homes with large kitchen exhaust fans, furnace cold air returns, fresh air exchange systems and any other air system in close proximity to the heating appliance may create a negative pressure in the same room as the heating appliance. This can create dangerous ...
-
Lennox Hearth SWS210 - page 6
6 WA RNING: BE ABSOLUTEL Y SURE THE DIST ANCE BETWEEN THE HEA TER AND THE SURF ACE OF ANY COMBUSTIBLE CONSTRUC- TION IS NOT LESS THAN SHOWN IN THE FIGURES ON P AGE 7. Floor Protection USA - The floor in front and under the heater must be protected with noncombustible material. The covering must extend 16” in front of the door opening of the heat ...
-
Lennox Hearth SWS210 - page 7
7 A B D L †E †E K C H I J Floor Protection FLOOR PROTECTION I M F F T Floor Protection G G K 48 ” Ma x. De pth T op V i ew Co rne r C lea r an ce, St o ve an d F lue to W a ll NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 6” Ø Flue Collar Figure 4 PIPE INST ALLA TION A B (1) C D (1) E† F (1,4) Si ngl e W al l Re sid e nt ial USA ...
-
Lennox Hearth SWS210 - page 8
8 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Shown with T ubinox™ Stainless Steel Liner components (see Page 29 for ordering information) Chimney T ermination Cap Chimney T ermination Rain Cap Masonry Adaptor Length 90° T ee Storm Collar Roof Flashing Flashing Ceiling Support Assembly Slip Adaptor Chimney Connector 6” x 24” 24-gag ...
-
Lennox Hearth SWS210 - page 9
9 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Manufactured Home Installations (ref. Figure 7 ) This appliance is approved for installation into a manufactured (mobile) home in the USA ONL Y! Installation should be in accordance with the Mobile Home Construction and Safety Standard, Title 24 CFR, Part 3280 (in Canada CAN/CSA Z240 MH), or , ...
-
Lennox Hearth SWS210 - page 10
10 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Chimney Connector Systems and Clearances from Combustible Walls for Residential Heating Appliances (NFPA 211) Refer to Figure 8 System A. Minimum 3.5 in. (90 mm) thick brick masonry wall framed into combustible wall with a minimum of 12 in. (305 mm) brick separation from clay liner to combust ...
-
Lennox Hearth SWS210 - page 11
11 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Figure 10 Figure 9 T o install the “Outside Air Kit,” position the clip so that the nut is directly above the hole punched in the back of the heatshield (See Figure 11 ) . Install the outside air adapter box on the stove by sliding it ...
-
Lennox Hearth SWS210 - page 12
12 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 1. If not previously installed, install floor protection and move the heater into the desired location. 2. Position the stove on your floor protection in the exact location where it is to be located, making sure all minimum clearances are met. 3. If you are installing outside air on your st ...
-
Lennox Hearth SWS210 - page 13
13 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 5. If required, install the Outside Air Kit (P/N 71112) as per the fol- lowing instructions. T o locate the hole in the hearth for outside air mark and cut a 4” (102 mm) hole in the hearth. The hole’ s center should be 3” (76 mm) directly forward from the center of the flue outlet or l ...
-
Lennox Hearth SWS210 - page 14
14 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 1. Check that all chimney pipe joints are securely fastened. 2. Check that the heater is securely fastened to the floor (if ap- plicable). 3. Make sure the intake vent has clear access to outside air (if ap- plicable). 4. Make sure the outside air vent has been sealed properly to keep rodent ...
-
Lennox Hearth SWS210 - page 15
15 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 3. Also included with the unit are two 15” x 10” x 1” thick baffle blankets. Install each blanket above the baffle board to each side of the second- ary support with the 15” side of the blanket from front to rear of the unit. Make sure that the baffle blankets are to the full rear ...
-
Lennox Hearth SWS210 - page 16
16 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Be sure to clean plated accessories with a household type cleaner and a very soft cloth to remove any fingerprints and residues prior to the first fire. 1. NEVER USE FLAMMABLE LIQUIDS TO ST ART OR REKINDLE A SOLID FUEL FIRE!! 2. Fully open the primary draft control by pulling the 1” plas ...
-
Lennox Hearth SWS210 - page 17
17 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. W ARNINGS The blower must be plugged directly into a properly grou nded three -pro ng rec epta cle, 120 V AC, 60 Hz, sin gle phase. Do not cut or remove the grounding prong from this plug. Do not route power cord under or in front of appliance. Installation must be in accordance with National ...
-
Lennox Hearth SWS210 - page 18
18 T o achieve long burn times, after having thoroughly preheated the stove, let the stovetop cool down to 275 to 400 degrees (on Elites, locate thermometer on the face of the insert just above the door). Now load the firebox and set the draft control. At this point, you may need to burn the stove with the draft open for a few minutes to ignite th ...
-
Lennox Hearth SWS210 - page 19
19 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. DOOR HINGES: If door hinges need lubricating, use an anti-seize com- pound (never use oil) available from your Lennox Hearth Products dealer . DOOR LA TCH: If your door latch fails to latch tightly and the gasket is in good condition, place a length of pipe (cheater bar) over the inside porti ...
-
Lennox Hearth SWS210 - page 20
20 Problem Solution POOR DRAFT : Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have poor drafts. Remember , the stoves’ draft depend solely on the natural draft of the chimney (See Draft Requirements on Page 4 ) . If your stove is not drafting properly , your chimney is the problem. A ...
-
Lennox Hearth SWS210 - page 21
21 DO NOT : Install or operate this stove before reading this manual. DO NOT : Close the draft beyond the point at which the flames are completely extinguished. DO NOT : Open the stove door without fully opening the draft first. DO NOT : Burn driftwood or wood that has been in salt water . This includes some mill ends and scrap lumber that has be ...
-
Lennox Hearth SWS210 - page 22
22 Contact an Lennox Hearth Products dealer to obtain any of these parts. Never use substitute materials. Use of non-approved parts can result in poor performance and safety hazards. REPLACEMENT PA RTS - MODELS SS210, ST210 AND SWS210 FRONT DOOR P ARTS LIST Item # Ca t. N o De scr i pt ion 1 H5639 Door Rope Kit, 7/8” Dia. (6’ 2”) 2 H5629 Uppe ...
-
Lennox Hearth SWS210 - page 23
23 REPLACEMENT P AR TS - MODEL SS210 48 46 47 34 35 41 41 45 39 39 43 39 39 39 39 43 39 39 36 40 40 40 40 44 37 38 39 39 39 42 39 39 39 42 33 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. ...
-
Lennox Hearth SWS210 - page 24
24 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P AR TS - MODEL ST210 AND SWS210 34 47 48 46 33 35 41 41 45 39 39 43 39 39 39 39 43 39 39 36 40 40 40 40 44 37 38 39 39 39 42 39 39 39 42 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. ...
-
Lennox Hearth SWS210 - page 25
25 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Door Parts Blower Parts 7 13 1 2 3 4 5 6 8 1 2 3 4 5 9 10 8 14 11 6 7 12 25 29 31 28 27 26 32 30 REPLACEMENT P AR TS - MODELS SS210, ST210 AND SWS210 ...
-
Lennox Hearth SWS210 - page 26
26 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P AR TS - MODELS SS210, ST210 AND SWS210 22 24 18 20 21 23 Leg and Leg Parts ...
-
Lennox Hearth SWS210 - page 27
27 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P AR TS - MODELS SS210, ST210 AND SWS210 15 18 15 18 19 16 17 19 Ash Drawer Pedestal and Pedestal ...
-
Lennox Hearth SWS210 - page 28
28 PE DES T ALS (R E QU IRE D ) C a t . N o . Mo d el De scr i pt ion 71 113 W L -P ED Pe des t al (ref. form #506033-16) 71 114 WL- P ED -AS H D As h D raw er P ed est a l (ref. form #506033-15) OR LE G S (RE Q UI RED ) (ref. form #506033-14) 70 000 LE G-O L Y -B Ol ymp i c Scu l pt ure d B l ac k L e gs (4 pe r p kg. ) 70 001 LEG -OL Y -G Ol ymp ...
-
Lennox Hearth SWS210 - page 29
29 ACCESSORIES - MODELS SS210, ST210 AND SWS210 Secure Black™ Single Wall Stove Pipe 6” SW Pipe and Accessories Cat. No. Model Description Pc. / Container 6SWL6 6SWL6 LENGTH 6” X 6” 100 6SWL12 6SWL12 LENGTH 6” X 12” 5 6SWL24 6SWL24 LENGTH 6” X 24” 10 6SWL36 6SWL36 LENGTH 6” X 36” 2 6SWL48 6SWL48 LENGTH 6” X 48” 5 6SWL T 6SWL ...
-
Lennox Hearth SWS210 - page 30
30 ACCESSORIES - MODELS SS210, ST210 AND SWS210 Secure T emp® Factory-Built Chimney 6” Secure T emp ASHT and Secure T emp G-ASHT Cat. No. Model Description Pc. / Container Lengths and Fittings 6L8 6L8 LENGTH 6” X 8” 1 6L12 6L12 LENGTH 6” X 12” 1 6L18 6L18 LENGTH 6” X 18” 1 6L24 6L24 LENGTH 6” X 24” 1 6L36 6L36 LENGTH 6” X 36” ...
-
Lennox Hearth SWS210 - page 31
31 SAFETY / LISTING LABEL - ENGLISH 2011 2012 2013 ...
-
Lennox Hearth SWS210 - page 32
32 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. SAFETY / LISTING LABEL - FRENCH ...
-
Lennox Hearth SWS210 - page 33
33 NOTES ...
-
Lennox Hearth SWS210 - page 34
Printed in U.S.A. © 2007 by Lennox Hearth Products P/N 775215M Rev . F 09/2011 Lenn ox Hearth Produ cts reserves the right to make changes at any time , without notic e, in desig n, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. 34 Y our Applia ...
Lennox Hearth SWS210についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもLennox Hearth SWS210の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLennox Hearth SWS210で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。