Weil-McLain Radiant Heaterの取扱説明書

20ページ 0.71 mb
ダウンロード

ページに移動 of 20

Summary
  • Weil-McLain Radiant Heater - page 1

    P art No. 650-000-221/0298 These Instructions must be used only by a qualified installer/service technician. Read these instructions completely before beginning. Failure to follow these instructions can cause severe personal injury , death or substantial property damage. ...

  • Weil-McLain Radiant Heater - page 2

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 2 Hazard Definitions Indicates presence of hazards that will or can cause minor personal injury or property damage. Indicates special instructions on installation, operation or maintenance that are important but not related to personal injury or property hazards. Indicates presence of hazards ...

  • Weil-McLain Radiant Heater - page 3

    Above Floor Installation Guide P art Number 650-000-221/0298 3 T ube Layouts for Radiant Heating Obtain T ube Layout Drawing Meet with General Contractor Obtain Materials Obtain Special Equipment P re-Installation Check List Mark T ube Layout on Subfloor Mount Manifold(s) Install the T ubing Before Leaving the Jobsite . . . Inspect T ubing Before F ...

  • Weil-McLain Radiant Heater - page 4

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 4 A . T ube Layouts for Radiant Heating 1. Radiant Floor Heatng a. Hot water flowing in the radiant tubing under the finished flooring heats the flooring and the heat emission plates. The heat emission plates help spread the heat evenly across the flooring. b . Heat must pass through the floor ...

  • Weil-McLain Radiant Heater - page 5

    Above Floor Installation Guide P art Number 650-000-221/0298 5 Figure 2 - T ypical tube routing for an above floor installation ABO VE FLOOR INST ALLA TION (One- W ay Serpentine P atterns - T ypical) Constant Spacing Outside W all Concentrated Spacing (W all with large window area or cool wall) These drawings are conceptual only . Consult W eil-McL ...

  • Weil-McLain Radiant Heater - page 6

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 6 Normal Close Inches Inches Feet Feet Feet F eet LR1 Low pile carpet w/ t hermal pad 8.5 178 43 10 231 LR2 Low pile carpet w/ t hermal pad 8.5 6.5 192 22 10 224 DK Lamin ated hardwood 12.5 6.5 227 28 10 265 UT Ceramic tile 6.5 45 4 10 59 BT Ceramic tile 6.5 79 12 10 101 BR1 Lamin ated hardwoo ...

  • Weil-McLain Radiant Heater - page 7

    Above Floor Installation Guide P art Number 650-000-221/0298 7 B . Obtain T ube Layout Drawing 1. Do not start a radiant heating installation without a detailed tube layout drawing. • It provides critical information on: • tube routing • tube lengths • areas to be avoided • materials needed 2. Figure 3 includes the information and drawing ...

  • Weil-McLain Radiant Heater - page 8

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 8 1. W e suggest you meet with the general contractor and follow this checklist: q Review the AlumiPex Trade Guides with the general contractor and ask him to provide the information and copies to each of the trades involved. q V erify that the flooring system is rated by the flooring manufact ...

  • Weil-McLain Radiant Heater - page 9

    Above Floor Installation Guide P art Number 650-000-221/0298 9 D . Obtain Materials 3. AlumiPex Manifolds • A vailable in three sizes (2, 3 and 4 takeoff) in nickel-plated brass (shown above), with or without integral balancing valves . • Copper manifolds (not shown) are also available. • Refer to AlumiPex Manifold Instructions for part numbe ...

  • Weil-McLain Radiant Heater - page 10

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 10 E . Obtain Special Equipment 1. T ubing Uncoiler  Assists in tube installation. 2. AlumiPex T ube Cutter 4. Pressure Gauge  W ith a scale range of 150 psig.  For pressure testing and tubing pressurization. 3. AlumiPex Reamer/Sizer(s)  The reamer/sizer is specific to tube diamete ...

  • Weil-McLain Radiant Heater - page 11

    Above Floor Installation Guide P art Number 650-000-221/0298 11 G . Mark Floor Plan and T ube Layout on Subfloor 1. Use the T ube Layout Plan to mark the following on the subfloor . Use several colors if possible to define different elements and circuits.  See Figure 7 for typical layout markings for the system shown in Figure 6, page 6.  Mar ...

  • Weil-McLain Radiant Heater - page 12

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 12 H . Mount Manifold(s) 1. Accurately measure the location of the manifold mounting wall (if not already installed).  Placement of the manifold and the tube penetrations is critical.  T ake extra care in laying out these locations so all items will be in proper position for the interior ...

  • Weil-McLain Radiant Heater - page 13

    Above Floor Installation Guide P art Number 650-000-221/0298 13 Figure 8 - Mounting of manifold(s), typical MANIFOLD MOUNTING (Above Floor System) The details shown are representati ve only . Other mounting conf igurations are possible. AlumiP ex Manifold, T ypical ! Refer to AlumiPex Manifold Instructions for details of mounting, assembly and appl ...

  • Weil-McLain Radiant Heater - page 14

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 14 I. Install the T ubing 1. Install the sleepers.  Beginning from one side of each room, use your floor markings and the tube layout drawing to place the sleepers.  Glue and nail each sleeper in place as shown in Figure 10.  Bend routing sleepers can be made using a router and fixtur ...

  • Weil-McLain Radiant Heater - page 15

    Above Floor Installation Guide P art Number 650-000-221/0298 15 Figure 10 - T ypical sleeper layout and installation 5 5 5 SLEEPER LA YOUT - ABO VE FLOOR (T ypical) 1 SLEEPERS ! ! ! ! T ypically sleepers are 1 x __ lumber or . Space 1" apart as shown to pro vide room for heat emission plate tubing channel and for thermal expansion. Begin at on ...

  • Weil-McLain Radiant Heater - page 16

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 16 Figure 11 - T ypical above floor installation ABO VE FLOOR INST ALLA TION This drawing is conceptual only . Consult Weil-McL ain Radiant Guides or Software for actual project layout. A Finished Flooring J J Subflooring I I Joists H H P oly-wrapped Insulation G Mark the T ubing Locations ! ! ...

  • Weil-McLain Radiant Heater - page 17

    Above Floor Installation Guide P art Number 650-000-221/0298 17 J . P ressure T est the Finished T ubing Installation 1. After all tubing has been routed and connected to the manifold, pressure test all tubing circuits before finished flooring is installed. Refer to AlumiPex Manifold Instructions. 2. Isolate the AlumiPex manifolds and tubing from a ...

  • Weil-McLain Radiant Heater - page 18

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 18 K. P ressurize T ubing for Observation 1. After the system has been proven leak free, pressurize all tubing circuits to 30 psig.  Maintain this pressure on the tubing for the remainder of the building construction.  Pressurizing the tubing allows use of the pressure gauge to verify th ...

  • Weil-McLain Radiant Heater - page 19

    Above Floor Installation Guide P art Number 650-000-221/0298 19 O . Inspection, Repair and T roubleshooting 1. Inspect the tubing connections and piping as the job is completed. 2. Perform a final pressure test on the system after all flooring is in place and building is ready for occupancy to verify all joints are tight and no damage has occurred ...

  • Weil-McLain Radiant Heater - page 20

    AlumiP ex Radiant T ubing P art Number 650-000-221/0298 20 ...

メーカー Weil-McLain カテゴリー Electric Heater

Weil-McLain Radiant Heaterのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Radiant Heaterの取扱説明書
- Weil-McLainの製品カード
- パンフレット
- またはWeil-McLain Radiant Heaterの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Weil-McLain Radiant Heaterの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Weil-McLain Radiant Heaterの取り付け説明書、サービスマニュアル、簡易説明書、またはWeil-McLain Radiant Heaterのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Weil-McLain Radiant Heaterの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Weil-McLain Radiant Heaterデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWeil-McLain Radiant Heaterを使用するのを助ける技術的文書のことです。説明書は通常、全てのWeil-McLain Radiant Heaterユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Weil-McLainの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Weil-McLain Radiant Heaterの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWeil-McLain Radiant Heaterの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Weil-McLain Radiant Heaterに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Weil-McLain Radiant Heaterデバイスの基本機能を使うにあたってのヒント。 Weil-McLain Radiant Heaterのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Weil-McLain Radiant Heaterに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWeil-McLain Radiant Heaterのメーカー/サービスへの連絡先に関する情報。

Weil-McLain Radiant Heaterについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWeil-McLain Radiant Heaterの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWeil-McLain Radiant Heaterで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)