日本語 dropdown-ico

VDO Cyclecomputing Cytec C05+の取扱説明書

20ページ 0.53 mb
ダウンロード

ページに移動 of 20

Summary
  • VDO Cyclecomputing Cytec C05+ - page 1

    BEDIENUNGSANLEITUNG INSTRUCTION MANUAL MANUEL D´INST ALLA TION ET D´UTILISA TION MANUALE D´INST ALLAZIONE E FUNZIONAMENTO INST ALACION Y OPERACIÓN MANUAL HANDLEIDING NÁVOD K MONTÁŽI A OBSLUZE INSTRUKCJA OBSLUGI LICZNIKA INST ALLA TIONS OG BETJENINGSVEJLEDNING BRUKSANVISNING BRUKSANVISNING ASENNUS JA KÄYTTÖOHJEKIRJA CYCLECOMPUTING C05+ ...

  • VDO Cyclecomputing Cytec C05+ - page 2

    1 GB INST ALLA TION AND OPERA TION MANUAL - VDO CYTEC C05+ Preface Thank you for buying a VDO CYTEC bicycle computer . The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual. Y ou are getting important and useful hints for operation to make you ful ...

  • VDO Cyclecomputing Cytec C05+ - page 3

    GB 2 W arning: Before tightening the handlebar holder , make sure to adjust the position of the computer head (inclination) when the LCD-display is best visible for you. Only when you find the best position tighten the screw . screw ...

  • VDO Cyclecomputing Cytec C05+ - page 4

    3 GB 1.2 Mounting the speed transmitter / sender The sensor should be mounted on the same side of the fork as the holder is on the handlebar . Make sure to position the respective rubber shim between fork and sender , position the curved back of the sender next to the spokes and make sure the sender is aimed at the receiver (computer head). Importa ...

  • VDO Cyclecomputing Cytec C05+ - page 5

    GB 4 1.3 Mounting the spoke magnet Distance between magnet and sensor should be approx. 1-5 mm. In case this distance is not achievable in the current positioning, slide the sensor and the magnet on the fork or spoke accordingly . W atch out: Please remove the computerhead from the handlebar holder when you intend not to use your bike for a longer ...

  • VDO Cyclecomputing Cytec C05+ - page 6

    5 GB 1.4 Installing battery into computer head T o save battery power , your VDO CYTEC C05+ comes with the battery not yet fitted. Prior to initial use you have to install the battery first. Insert battery with positive (+) end on top. W atch out: Once the battery is properly fitted, the computer immediately changes into set-up mode (see also chapt ...

  • VDO Cyclecomputing Cytec C05+ - page 7

    GB 6 1.5 Function Indicator Y our VDO CYTEC C05+ features a function indicator ((1)). When you are done mounting the computer , ((1)) flashes at the first rotation of the wheel. When the wheel-size is properly entered, actual speed is displayed as well.(see chapter 5). In case the function-indicator ((1)) is not flashing, please double-check: Is th ...

  • VDO Cyclecomputing Cytec C05+ - page 8

    7 GB UNLOCK LOCK 1.LOCK 2.CLICK 1.PRESS 2.UNLOCK ...

  • VDO Cyclecomputing Cytec C05+ - page 9

    GB 8 3. Information features of your VDO CYTEC C05+ Y our VDO CYTEC C05+ provides you with following information: KMH-MPH current speed indicated in either KMH or MPH, featuring automatic conversion into MPH DST trip counter , counts your trip distance up to 999,99 km or miles. A TM trip timer , keeps track of the actual riding time featuring autom ...

  • VDO Cyclecomputing Cytec C05+ - page 10

    This button / key has several functions. All functions of the button / key are outlined in the chart below . Y our display Button / Key to Length of pushing What is going on? indicates following be pushed the button / key information DST -ODO-CLK-A TM push MODE key brief (0.1 sec) next information from DST or ODO or A TM is indicated. ODO push MODE ...

  • VDO Cyclecomputing Cytec C05+ - page 11

    GB 10 5.1 Programming (setting up) your wheelsize In order for the VDO CYTEC C05+ to indicate your actual speed and your trip distance, the correct wheelsize has to be entered. Wheelsize is the outer circumference of the wheel including the tire. following default is entered wheelsize = WS = 2124 mm W atch out: Above default is automatically applie ...

  • VDO Cyclecomputing Cytec C05+ - page 12

    11 GB W atch out: In case you have selected MPH readout you must enter your wheelsize in mm. WS in mm 1x ...

  • VDO Cyclecomputing Cytec C05+ - page 13

    GB 12 5.3 Entering your wheelsize / entering odometer After initially installing the battery or after a battery change, your VDO CYTEC C05+ automatically switches into set-up mode for wheelsize and odometer . Start with Step 3. Y ou might as well enter the set-up mode for wheelsize and odometer at any time by proceeding as follows: Step 1: Call ODO ...

  • VDO Cyclecomputing Cytec C05+ - page 14

    13 GB In case you wish to enter the precise wheelsize you have measured yourself (i.e. 2257), please proceed with step 5. Step 5 : Not pressing the MODE button with in 2 seconds will make the last digit (212 4 ) flash and change the value (4-5-6-7...) Once the correct digit (7) comes up, press the mode button. Now the third digit flashes and change ...

  • VDO Cyclecomputing Cytec C05+ - page 15

    GB 14 Press immediatly 5 times to end Press to Stop switch to ne xt Press to Stop switch to ne xt Press to Stop switch to ne xt Press to Stop switch to ne xt Press to Stop switch to ne xt Please wait 2 sec. until counting Press to Stop switch to ne xt Press to Stop switch to ne xt Press to Stop switch to ne xt Press to switch Set ODOMETER Return to ...

  • VDO Cyclecomputing Cytec C05+ - page 16

    15 GB 5.4 Setting the clock CLK Y our VDO CYTEC C05+ features a clock with hour and minute display in 24 h mode T o access the clock set-up mode proceed as follows: Step 1: call in the CLK information into your display Step 2: Press the MODE button for 5 sec. The set-up mode for the clock starts. Y ou will see the digit flashing and changing its va ...

  • VDO Cyclecomputing Cytec C05+ - page 17

    6. Resetting information to zero The following information may be reset to zero with your VDO CYTEC C05+: DST = trip distance A TM = trip counter W atch out: Both these information are simultaneously reset to zero T o reset either DST or A TM, one of these informations has to be displayed. Resetting to zero is done by pressing the MODE button for f ...

  • VDO Cyclecomputing Cytec C05+ - page 18

    Hg 17 GB 8 . Battery change Tip: T ake down your total distance and wheelsize prior to battery change. 8.1 Changing the battery in the computer head see chapter 1.4. W atch ou t : old batteries require special disposal 9. T roubleshooting This chart outlines possible malfunctions, their causes and solutions. malfunction possible cause solutions spe ...

  • VDO Cyclecomputing Cytec C05+ - page 19

    GB 18 8 . Battery change Tip: T ake down your total distance and wheelsize prior to battery change. 8.1 Changing the battery in the computer head see chapter 1.4. W atch ou t : old batteries require special disposal 9. T roubleshooting This chart outlines possible malfunctions, their causes and solutions. malfunction possible cause solutions speed ...

  • VDO Cyclecomputing Cytec C05+ - page 20

    19 GB Contents 1 computer head 1 handlebar holder with screw 1 wireless transmitter with battery 12 V , type V23GA 1 rubber shim for sensor mount 1 spoke magnet 5 cable ties 1 battery 3 V , type CR 2032 1 installation and operation manual TIP The CYTEC tin box easily holds a mini-tool and a spare tube to carry on with your ride. ...

メーカー VDO Cyclecomputing カテゴリー Cyclometer

VDO Cyclecomputing Cytec C05+のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Cytec C05+の取扱説明書
- VDO Cyclecomputingの製品カード
- パンフレット
- またはVDO Cyclecomputing Cytec C05+の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、VDO Cyclecomputing Cytec C05+の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、VDO Cyclecomputing Cytec C05+の取り付け説明書、サービスマニュアル、簡易説明書、またはVDO Cyclecomputing Cytec C05+のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、VDO Cyclecomputing Cytec C05+の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

VDO Cyclecomputing Cytec C05+デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがVDO Cyclecomputing Cytec C05+を使用するのを助ける技術的文書のことです。説明書は通常、全てのVDO Cyclecomputing Cytec C05+ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

VDO Cyclecomputingの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. VDO Cyclecomputing Cytec C05+の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははVDO Cyclecomputing Cytec C05+の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。VDO Cyclecomputing Cytec C05+に関してこのドキュメントで見つけることができる全てのヒントの目次
3. VDO Cyclecomputing Cytec C05+デバイスの基本機能を使うにあたってのヒント。 VDO Cyclecomputing Cytec C05+のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。VDO Cyclecomputing Cytec C05+に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるVDO Cyclecomputing Cytec C05+のメーカー/サービスへの連絡先に関する情報。

VDO Cyclecomputing Cytec C05+についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもVDO Cyclecomputing Cytec C05+の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがVDO Cyclecomputing Cytec C05+で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)