APC AP9613の取扱説明書

32ページ 0.48 mb
ダウンロード

ページに移動 of 32

Summary
  • APC AP9613 - page 1

    Inst allation and Configuration Dry Cont act I/O SmartSlot Card AP9613 ...

  • APC AP9613 - page 2

    This manual is available in English on the enclosed CD. ...

  • APC AP9613 - page 3

    Content s Dry Contact I/O SmartSlo t Card i Safety Overview 1 Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Overview 2 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product description 2 Hardware and software requirements and tools needed 3 Showin ...

  • APC AP9613 - page 4

    Dry Contact I/O SmartSlo t Card ii Disclaimer 20 APC Worldwide Customer Support 32 ...

  • APC AP9613 - page 5

    Dry Contact I/ O SmartSlot Card 1 Safety Overview Import ant Safety Information Follow all applicable electrical codes for your installation area. Read the instructions care fully to becom e familiar with the equipment before trying to install, operate, service or maintain it. The followi ng special m e ssag es may appear through out this manual or ...

  • APC AP9613 - page 6

    2 Dry Contact I/ O SmartSlot Card Product Overview Introduction The Schneider Electric™ Dry Contact I/ O SmartSlot Card (AP9613) is a management product that provides the fo llowing features: • UPS status information presented through 6 fully isol ated ou tput relays. This is expandable to 8 using universal input /output ports and optional Dry ...

  • APC AP9613 - page 7

    Dry Contact I/ O SmartSlot Card 3 Hardware and sof tware re quirements and tools needed The Dry Contact I/O SmartSlot Card works with most APC by Schneider Electric UPS devices with an output rated less than or equal to 160kV A and an available SmartSlot. While most devices meet this requirement ; verify the compatibility of your device by locating ...

  • APC AP9613 - page 8

    4 Dry Contact I/ O SmartSlot Card Showing the product det ail Itemizing the features of the Dry Contact I/O SmartSlot Card         ...

  • APC AP9613 - page 9

    Dry Contact I/ O SmartSlot Card 5 Item Name Description  Universal I/O ports 1 and 2 These support the AP9335 T/ TH and AP9810 dry contact accessories  USB cable connector Connecting this to your PC enab les usage of the Configuration Utility .  Reset button Use an appropriately sized, non-metallic tool to press the Reset button. Holding t ...

  • APC AP9613 - page 10

    6 Dry Contact I/ O SmartSlot Card Itemizing the input cont act and output relay terminal blocks Number of positions on each terminal block 9 T ightening torque 0.35 N.m T ightening torque max 0.4 N.m W ire stripping length 5 mm Minimum wire gauge 0.14 mm 2 (26 A WG) Maximum wire gauge 2.5 mm 2 (14 A WG) ...

  • APC AP9613 - page 11

    Dry Contact I/ O SmartSlot Card 7 Configuring th e Dip Switches The Dry Contact I/O SmartSlot Card requires configuration before test ing , final installatio n, and use. See “Location of dip switch es” directly below and “Dip switches: input and outputs” . Location of dip switches The “callout” below points to the lo catio n of the dip ...

  • APC AP9613 - page 12

    8 Dry Contact I/ O SmartSlot Card Dip switches: input and output s The table below lists the fo ur possible configurations, wi th their corresponding inputs and outputs. * W ith this setup (the factory default), the Configuration Utility is used automatically . Configuration 1 Configuration 2 C onfiguration 3 C onfiguration 4* OFF-OFF-OFF-ON ON- OF ...

  • APC AP9613 - page 13

    Dry Contact I/ O SmartSlot Card 9 Inst alling See “Planning your installatio n” directly below , “Installation steps” on page 12, and “Connecting to the configurati on uti lity” on page 14. Planning your inst allation Operating considerations Note the following character istics of the Dry Contact I/O SmartSlot Card wh en making decision ...

  • APC AP9613 - page 14

    10 Dry Contact I/ O SmartSlot Card inputs, we recommend that an outpu t be configured and monitored appropriately to determine th e effectiveness of an input. • Do not wire this Dry Contact I/O SmartSlot Card when the pow er is on. • The installation of this Dry Contact I/O SmartSlot Card must fol low applicable building and electrical codes. ? ...

  • APC AP9613 - page 15

    Dry Contact I/ O SmartSlot Card 11 Connection strategies Y ou can connect the alarm outputs of th e Dry Contact I/O SmartSlot Card in several ways to meet the requirements of your manage ment systems or switched load. Both normally open (N. O.) and normally closed (N. C.) systems are accommodated in any combination of AND or OR configurations. Y ou ...

  • APC AP9613 - page 16

    12 Dry Contact I/ O SmartSlot Card Inst allation step s W arning: After installat ion, it is stro ngly recommended that you fully test your configuration before puttin g it into a production environment. 1. Make all connections to the Dry Co ntact I/O SmartSlot Card to support your configurat ion before continuing . See “Itemizing the input conta ...

  • APC AP9613 - page 17

    Dry Contact I/ O SmartSlot Card 13 3. Orient the Card to fit in the Card slot as shown. Slide th e Card all the way into the slo t until the end plate is flush with the back p anel of the host device. T rying to inst all the Card upside down may damage it. Observe the correct orientation of the Card. The sides of the printed circuit board align wit ...

  • APC AP9613 - page 18

    14 Dry Contact I/ O SmartSlot Card Connecting to the configuration utility The Configuration Utilit y does not need to be installed, it runs off the Card. W ith the Utility , you can: • review the status of your AP9613 Dry Contact I/O SmartSlot Card and Universal I/O ports • p e r f o r m actions in response to a status change in an input port ...

  • APC AP9613 - page 19

    Dry Contact I/ O SmartSlot Card 15 T o run the Utility , launch the runme.hta file located in the root of the drive. For information on using the Configuration Utility user interface, refer to its online help. When you connect your Card with your PC using the USB cable, the Configuration Utili ty reads a file called config.lua on the Card. Each tim ...

  • APC AP9613 - page 20

    16 Dry Contact I/ O SmartSlot Card S pecifications For all specifications, when there is a dif ference between the VDE and UL approval standards, use the lower rating. Electrical, physical, envi ronmental, and approval specifications Item Specification Electrical Nominal switching capacity 3A@ 30 V AC or VDC Rated voltage 24 VDC Rated current 200 m ...

  • APC AP9613 - page 21

    Dry Contact I/ O SmartSlot Card 17 Ratings for input cont acts and output relays Relative Humi dity Operating Sto ra ge 0 to 95% 0 to 95% Approvals Emissions and Immuni t y V erification: FCC Part 15 Class A, EN 55022 Class A, EN 55024, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, E ...

  • APC AP9613 - page 22

    18 Dry Contact I/ O SmartSlot Card Wa r r a n t y T wo-Y ear Factory W arranty This warranty applies only to the products you purchase for your use in accordance with this manual. T erms of warranty APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. APC will repair or ...

  • APC AP9613 - page 23

    Dry Contact I/ O SmartSlot Card 19 OTHER ADVICE OR SER VICE IN CONNECTION WITH THE PRODUCTS. THE FOREGOING W ARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER W ARRANTIES AND REMEDIES. THE W ARRANTIES SET FOR TH ABOVE CONSTITUTE APC’S SOLE LIABILITY AND PURCHASER’S EXCLUSIVE RE ME DY FOR ANY BREACH OF SUCH W ARRANTIES. APC W ARRANTI ...

  • APC AP9613 - page 24

    20 Dry Contact I/ O SmartSlot Card Disclaimer The information presented in this manual is not warranted by Schneider Electric to be authoritative, erro r free, or complete. Schnei der Electric assumes no liability f o r damages, violati ons of code s, improper installation, system failures, or any other problems that cou ld ari se based on the use ...

  • APC AP9613 - page 25

    ...

  • APC AP9613 - page 26

    ...

  • APC AP9613 - page 27

    ...

  • APC AP9613 - page 28

    ...

  • APC AP9613 - page 29

    ...

  • APC AP9613 - page 30

    ...

  • APC AP9613 - page 31

    ...

  • APC AP9613 - page 32

    APC W orldwide Customer Support Customer support for this or any other product is available at no charge in any of the following ways: • V isit the APC W eb site to access documen ts in the APC Know ledge Base and to submit customer support requests. – www .apc.com (Corporate Headquarters) Connect to localized APC W eb sites for specific countr ...

メーカー APC カテゴリー Power Supply

APC AP9613のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- AP9613の取扱説明書
- APCの製品カード
- パンフレット
- またはAPC AP9613の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、APC AP9613の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、APC AP9613の取り付け説明書、サービスマニュアル、簡易説明書、またはAPC AP9613のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、APC AP9613の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

APC AP9613デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAPC AP9613を使用するのを助ける技術的文書のことです。説明書は通常、全てのAPC AP9613ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

APCの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. APC AP9613の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAPC AP9613の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。APC AP9613に関してこのドキュメントで見つけることができる全てのヒントの目次
3. APC AP9613デバイスの基本機能を使うにあたってのヒント。 APC AP9613のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。APC AP9613に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAPC AP9613のメーカー/サービスへの連絡先に関する情報。

APC AP9613についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAPC AP9613の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAPC AP9613で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)