-
Snapper 1733866 - page 1
A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T riple Catcher Mfg. No. Description 1695169 Clean Sweep Triple Catcher 1733866 Rev. 04 Rev. Date 12/2006 TP 100-4405-04-AT-SMAN Clean Sweep T riple Catc her ...
-
Snapper 1733866 - page 2
THIS P A GE INTENTIONALL Y BLANK (FOR PLA CEMENT ONL Y - DO NO T PRINT) ...
-
Snapper 1733866 - page 3
1 Normal Remov al & Installation Collector Installation ......................................10 Collector Remov al .........................................11 NOTE: In these instructions, “left” and “right” are referred to as seen from the operating position. Safety Rules & Inf ormation General W arnings ........................... ...
-
Snapper 1733866 - page 4
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The trian- gle in text signifies important cautions or warnings which must be followed. SAFETY DECALS This u ...
-
Snapper 1733866 - page 5
Bef ore Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag i ...
-
Snapper 1733866 - page 6
Initial Installation 4 Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). W ARNING Figure 1. Install Spacer (left side shown) A. Speed Nut, 5/16-18 B. Threaded Side C. Square Hole D. Shoulder Bolt, 5/16-18 E. Rear Frame Support B C D A A E Figure 3. Hitch Installa ...
-
Snapper 1733866 - page 7
5 T ube Component Assembly Baffle Installation 1. Determine which baffle to use. See Figure 4 Chart. 2. Lift side discharge chute (H, Figure 4). 3. Insert baffle (F) through discharge opening and posi- tion baffle into place. 4. Tighten carriage bolts (A) and nuts (E) on baffle (F). 5. Tighten carriage bolt (B) and nut (E) on baffle (F). 6. Positio ...
-
Snapper 1733866 - page 8
6 Component Installation Figure 6. Lower Chute to Boot Installation A. Pin, Latch B. Carriage Bolt, 1/4-20 x 5/8 C. Locknut, 1/4-20 D. Lower Chute E. Locknut, Center Lock, 5/16-18 F. Strap, Rubber G. Locknuts, Whiz Lock, 5/16-18 H. Rod, Boot Mount I. Capscrew, Hex Head, 5/16-18 x 1-1/4 J. Capscrew, Hex Head, Thin, 5/16-18 x 1 D B C F A G G H I J E ...
-
Snapper 1733866 - page 9
Install Upright Support & Bag Support Bracket 7 Figure 8. Install Upright Support A. Hitch B. Upright Support C. Capscrews, 3/8-16 x 1 D. Locknuts, 3/8-16 A INSTALL UPRIGHT SUPPORT TO HITCH 1. Install the upright support (B, Figure 8) to hitch (A) and secure with 3/8-16 x 1 capscrews (C) and lock- nuts (D) as shown. B INSTALL BAG AND COVER SUPP ...
-
Snapper 1733866 - page 10
Cover and Bag Installation 8 Figure 10. Install Cover Assembly A. Bag Support Bracket B. Cover Assembly C. Cover Hinge Pins D. Hair Pins E. Hinge Pivots D INSTALL COVER ASSEMBLY 1. Attach cover assembly (B, Figure 10) to bag support bracket (A) using hinge pivots (E). Secure cover using cover hinge pins (C) and hair pins (D) as shown. INSTALL COLLE ...
-
Snapper 1733866 - page 11
9 T ube Installation C D E A B Figure 12. Install Lower Tube A. Lower Chute Rod B. Mounting Plate C. Rubber Strap D. Discharge Deflector E. Locknut LOWER TUBE INSTALLATION 1. Lift discharge deflector up (D, Figure 12). 2. Insert lower chute rod (A) into mounting plate (B). 3. Pull rubber strap (C) and secure by placing hole clos- est to knob in str ...
-
Snapper 1733866 - page 12
Normal Removal & Installation 10 A. Hitch Support Assembly J. Deflector B. Cover K. Nut & Capscrew C. Pin L. Mounting plate D. Hair Pins M. Lower Chute Rod E. Bag N. Lower Chute F. Grass Bag Hanger O. Pin G. Upper Tube P. Strap, Middle H. Middle Tube Q. Ridge I. Strap, Boot R. Ridge Cutout E Q D B Normal Remo val & Installation Collecto ...
-
Snapper 1733866 - page 13
Normal Removal 11 Collector Remov al 1. Unhook strap (P, Figure 15) from pin (O). Slide mid- dle tube (H) into upper tube (G) and remove middle tube (H). Remove upper tube (G) from cover (B). 2. Lift up cover (B) remove and empty bags (E). 3. Unhook strap (I) from locknut and capscrew (K). Remove lower chute (N) from mounting plate (L). See that th ...
-
Snapper 1733866 - page 14
Simplicity Mfg. Inc.500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com Simplicity Mfg. Inc. - Snapper Products 535 Macon Street McDonough, GA 30253 www.Snapper.com Briggs & Stratton Yard Power Products Group Copyright © 2006 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved Simplicity Mfg. ...
Snapper 1733866についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもSnapper 1733866の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper 1733866で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。