Ingersoll-Rand 8476-Aの取扱説明書

12ページ 0.82 mb
ダウンロード

ページに移動 of 12

Summary
  • Ingersoll-Rand 8476-A - page 1

    OPERATORS MANUAL a- SECTION MANUAL INCLUDING: OPERATION, INSTALLATION & MAINTENANCE “0004” SERIES GRINDERS Released: 10/72 Revised: 3-l0-95 Form: 006-2 Tool Products Models: 8475-A-( ), 8475-A1, 8476-A, 8476-A1, 8477-A, 8477-A1, 8478-A and 8478-A1. READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE ...

  • Ingersoll-Rand 8476-A - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. Wear eye protection when operating or performing maintenance on this tool. Turn off air supply and disconnect air supply hose before installing, , removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Do not carry the tool by the hose. D ...

  • Ingersoll-Rand 8476-A - page 3

    ROUTINE LUBRICATION REQUIREMENTS Ml0 32 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voirof recommended F.R.L. with spindle oil (29665). If an in line or air line lubricator is not u ...

  • Ingersoll-Rand 8476-A - page 4

    MODEL IDENTIFICATION The grinder models listed in the model identification table above are furnished with a collet as standard equipment and are intended for use with mounted wheels and shall not be used with other type grinding wheels. Other size collet inserts or other collet assemblies listed on page 10 can be furnished with the above listed mod ...

  • Ingersoll-Rand 8476-A - page 5

    DISASSEMBLY AND ASSEMBLY OF TOOLS Ml0 Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and Instal- lation” section. To minimize ...

  • Ingersoll-Rand 8476-A - page 6

    TYPICAL CROSS SECTION OF TOOL -VALVE - MOTOR SPINDLE 6 ...

  • Ingersoll-Rand 8476-A - page 7

    SPINDLE SECTION Ml 3 COLLET NUT 41751 T r COLLET BODY 43178 -- _- - - COLLET ASSEMBLY 43179-( ) COLLET (SEE TABLE, PAGE 4) ET ASSEMBLY 44123 COLLET ASSEMBLY 44124-8 -INCLUDED WITH NOSE PIECE 33220 ‘!-COLLET 31812-8 COLLET GUARD 43897 DIFFUSER 43893 COLLET 41750-3 SPINDLE 44602 LOCK NUT 31810 NOSE PIECE 31811 COLLET 31812-8 -- - - (INCLUDES BEARIN ...

  • Ingersoll-Rand 8476-A - page 8

    SPINDLE SECTION DISASSEMBLY a. Remove driver (43163) from spindle. Tap end of spindle with a soft face hammer to loosen and remove spindle out nose end (44605) and bearing (33237) to housing. of housing. b. Assemble spindle to housing and assemble driver (43163) to spindle. ASSEMBLY a. Assemble felt seal (44606), wave washer (43150), bearing (42516 ...

  • Ingersoll-Rand 8476-A - page 9

    VALVE SECTION Ml0 32 0 43160 LEVER FOR NON -EU MODELS 0 45953 LEVER ASS’Y FOR -EU MODELS Cl * LEVER - ROLL PIN Yl78-44 __o__I ROLL PIN Yl78-216 r , BUT HOUSING431761 (BUlTON THROTTLE) ------ROLL PIN Yl78-211 (BUTTON THROTTLE) HOUSING 43161 (LEVER THROlTLE, NON -EU) (LEVER - VALVE 43170 V~UTTON THROTTLE) .TON 43169 SPRING 31125-----@ v REGULATOR 4 ...

  • Ingersoll-Rand 8476-A - page 10

    ACCESSORIES OPTIONAL COLLETS COLLET COLLET NUMBER ASSEMBLY NO. SIZE CAPACITY 41750-1 43179-1 1/8" 3/32” - 1/8” 41750-2 43179-2 3/16” 5/32” - 3/1 6” 41750-3 43179-3 1/4” 7/32” - 1/4” 41750-11 43179-11 3mm 41750-12 43179-12 I - ------ I 6mm I SERIES 43179 3-PIECE COLLETS COLLET NUT - 41751 COLLET BODY - 43170 5/16” - 24 THREAD ...

  • Ingersoll-Rand 8476-A - page 11

    TROUBLE SHOOTING Ml0 32 LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYONDTHE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTlON OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE HARD TO OPERATE. TOOL WILL NOT S ...

  • Ingersoll-Rand 8476-A - page 12

    Part of world wide Ingersoll-Rand PN49999-116 ...

メーカー Ingersoll-Rand カテゴリー Grinder

Ingersoll-Rand 8476-Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 8476-Aの取扱説明書
- Ingersoll-Randの製品カード
- パンフレット
- またはIngersoll-Rand 8476-Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ingersoll-Rand 8476-Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ingersoll-Rand 8476-Aの取り付け説明書、サービスマニュアル、簡易説明書、またはIngersoll-Rand 8476-Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ingersoll-Rand 8476-Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ingersoll-Rand 8476-Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがIngersoll-Rand 8476-Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのIngersoll-Rand 8476-Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ingersoll-Randの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ingersoll-Rand 8476-Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははIngersoll-Rand 8476-Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ingersoll-Rand 8476-Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ingersoll-Rand 8476-Aデバイスの基本機能を使うにあたってのヒント。 Ingersoll-Rand 8476-Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ingersoll-Rand 8476-Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるIngersoll-Rand 8476-Aのメーカー/サービスへの連絡先に関する情報。

Ingersoll-Rand 8476-Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもIngersoll-Rand 8476-Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがIngersoll-Rand 8476-Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)