Eaton QSNAPの取扱説明書

30ページ 0.98 mb
ダウンロード

ページに移動 of 30

Summary
  • Eaton QSNAP - page 1

    Publication No. MN05001001E February 2002 New Intelligent T echnologies QCPort Starter Network Adapter Product (QSNAP) Installation and User Manual ...

  • Eaton QSNAP - page 2

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E February 2002 Important Notice – Please Read The product discussed in this literature is subject to terms and conditions outlined in appropriate Eaton’ s Cutler -Hammer selling policies. The sole source governing the rights and remedies of any purchaser of this equipment is the relevan ...

  • Eaton QSNAP - page 3

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E i February 2002 T able of Contents PRODUCT OVERVIEW Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Eaton QSNAP - page 4

    Intelligent Technologies ( IT. ) QSNAP ii Pub. No. MN05001001E February 2002 List of Figures Figure 1: QSNAP Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 2: QSNAP Dimensions, mm [in] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Figure 3: Starter Interface Connec ...

  • Eaton QSNAP - page 5

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 1 February 2002 Product Overview Description Cutler -Hammer Intelligent T echnologies ( IT . ) QSNAP (QCPort Starter Network Adapter Product) by Eaton Corporation is the result of a substantive engineering and marketing effort, involving extensive customer input. This product has greatly i ...

  • Eaton QSNAP - page 6

    Intelligent Technologies ( IT. ) QSNAP 2 Pub. No. MN05001001E February 2002 Features and Benefits The IT . QSNAP includes the following significant features: ● Communication to QCPort consuming a single QCPort ID ● Control of non-reversing and reversing Eaton’ s Cutler -Hammer Intelligent T echnologies ( IT . ) Electromechanical Starters ? ...

  • Eaton QSNAP - page 7

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 3 February 2002 Safety The following safety statements relate to the installation, setup and operation of Eaton’ s Cutler -Hammer IT . QSNAP and Starter . Notice Make sure you read and understand the installation procedures in this manual before you attempt to operate or set up the equip ...

  • Eaton QSNAP - page 8

    Intelligent Technologies ( IT. ) QSNAP 4 Pub. No. MN05001001E February 2002 Environmental Ratings The following environmental ratings apply to the QSNAP . T able 3: Environmental Ratings Approvals/Certifications The following approvals and certifications apply to the QSNAP . T able 4: Approvals/Certifications Catalog Numbering System There is on ...

  • Eaton QSNAP - page 9

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 5 February 2002 Physical Features Physical Description Figure 1 illustrates the front and back of the IT . QSNAP and its various features. Figure 1: QSNAP Features Dimensions Figure 2 illustrates the dimensions of the IT . QSNAP . Figure 2: QSNAP Dimensions, mm [in] Feet Contactor Detector ...

  • Eaton QSNAP - page 10

    Intelligent Technologies ( IT. ) QSNAP 6 Pub. No. MN05001001E February 2002 Power Source The IT . QSNAP is designed for use with 24V DC power . The QSNAP uses power from two sources when operating properly; these sources are the QCPort subnet and the Eaton ’ s Cutler -Hammer Intelligent T echnologies ( IT . ) Electromechanical Starter . This allo ...

  • Eaton QSNAP - page 11

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 7 February 2002 CAUTION Only apply 24V DC to the QSNAP . Use of any other voltage may result in personal injury , property damage and damage to the QSNAP . ...

  • Eaton QSNAP - page 12

    Intelligent Technologies ( IT. ) QSNAP 8 Pub. No. MN05001001E February 2002 Operation This section provides details about the following features and aspects of QSNAP operation: ● “ Out of box ” operation ● T ypical application ● Enhanced features ● Input/output data ● Status LED ● T ruth table “Out of Box” Operation When the QSN ...

  • Eaton QSNAP - page 13

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 9 February 2002 T ypical Application The following fi gure illustrates a typical QSNAP application, where a single QSNAP is connected to one motor controller and where the motor controllers are distributed throughout QCPort. The subnet is then being controlled by a PC or PLC, which scans ...

  • Eaton QSNAP - page 14

    Intelligent Technologies ( IT. ) QSNAP 10 Pub. No. MN05001001E February 2002 Enhanced Features The QSNAP offers a variety of enhanced features, including: settable warnings, current threshold warning, underload warning and reset. T o help diagnose an application, a fault queue is provided to view the last fi ve faults. Refer to the following two t ...

  • Eaton QSNAP - page 15

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 11 February 2002 Input/Output Data The QSNAP offers a standard data list (shown below) for default operation. The list is con fi gurable with data contained within T able 21 in Appendix A: QSNAP Parameters , using the CH Studio application. Input Data Use T ables 10 and 11 when setting up ...

  • Eaton QSNAP - page 16

    Intelligent Technologies ( IT. ) QSNAP 12 Pub. No. MN05001001E February 2002 T able 11: Default Input Data Output Data Use T ables 12 and 13 when setting up the QSNAP output data. T able 12: Default Output Data T able 13: Output Assembly Data Definitions Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 3-Phase A verage RMS Current LSB Byte 0 3-Phas ...

  • Eaton QSNAP - page 17

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 13 February 2002 Status LED The status LED is located on the lower right of the QSNAP as pictured in Figure 1: QSNAP Features . The LED ’ s status changes depending on the state of the QSNAP . The following table lists the IT . QSNAP LED statuses and describes the meaning of each state. ...

  • Eaton QSNAP - page 18

    Intelligent Technologies ( IT. ) QSNAP 14 Pub. No. MN05001001E February 2002 Configuration The only con fi guration that is necessary for normal operation of the QSNAP is setting the Group ID and SW1 positions A and B, as described in the “ Installation ” section. However , the QSNAP offers a variety of enhanced features. When these features ...

  • Eaton QSNAP - page 19

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 15 February 2002 Installation Set the Group ID The Group ID refers to the logical QCPort group to which the QSNAP belongs. For further information on the explanation of Group ID and the system con fi guration, see the IT . QCPort System Install and Planning Guide (Publication No. MN050010 ...

  • Eaton QSNAP - page 20

    Intelligent Technologies ( IT. ) QSNAP 16 Pub. No. MN05001001E February 2002 SW1 Settings SW1 is used to set the existence of the second Aux contact and the external ground fault. T able 16: SW1 Settings Mount the IT . QSNAP to the Starter The IT . QSNAP is designed to be installed in the auxiliary contact locations of the IT . family of starters a ...

  • Eaton QSNAP - page 21

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 17 February 2002 Use the following steps and the illustration in Figure 7 to mount the QSNAP . 1. Align both the QSNAP feet with the auxiliary contact mounting slots on the starter , as illustrated in the fi gure. Recommendation: Use the middle mounting auxiliary contact on the contact bl ...

  • Eaton QSNAP - page 22

    Intelligent Technologies ( IT. ) QSNAP 18 Pub. No. MN05001001E February 2002 Wire the IT . QSNAP to the Starter The QSNAP is connected to the IT . starter using a factory-provided jumper with an RJ-45 plug on one end and a pigtail on the other . The pigtail is color coded to facilitate accurate connection to the overload terminal block. Refer to th ...

  • Eaton QSNAP - page 23

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 19 February 2002 2. T o lock the starter interface to the overload, rotate the orange locking tabs until the tab is locked into the slots in the overload. Use Figure 11 for information on which way to rotate the locking tabs. Note: Refer to the IT . Contactor and Starter User Manual (Publi ...

  • Eaton QSNAP - page 24

    Intelligent Technologies ( IT. ) QSNAP 20 Pub. No. MN05001001E February 2002 T roubleshooting and Maintenance Renewal Parts The renewal parts for the QSNAP are shown in the following table. T able 19: QSNAP Renewal Parts T roubleshooting T able 20: T roubleshooting Description Part Number J3 Jumper Consult Factory Starter Interface Consult Factory ...

  • Eaton QSNAP - page 25

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 21 February 2002 Appendix A: QSNAP Parameters Refer to the following table when con fi guring the QSNAP . T able 21: Configuration Parameters Number Parameter Length Units 1 Con fi g Data 14 2 Con fi guration CRC check 2 3 Node ID 2 4 QCPort mode 1 5 Baud Rate 1 6 Slave Address 1 7 Pro ...

  • Eaton QSNAP - page 26

    Intelligent Technologies ( IT. ) QSNAP 22 Pub. No. MN05001001E February 2002 T able 22: Data Parameters Number Parameter Units Length 11 Motor Control 1 12 Motor Control Status 1 13 Motor Control Faults 2 14 Button State 1 15 LED State 1 16 ASCII T ext 1 18 RMS AC Current Amps 4 22 Control DC V oltage Amps 2 23 Thermal Pile Percentage V olts 2 24 T ...

  • Eaton QSNAP - page 27

    Intelligent Technologies ( IT. ) QSNAP Pub. No. MN05001001E 23 February 2002 Intelligent T echnologies ( IT . ) Publications and Support T able 23: IT . Publications For copies of these and other publications contact the Literature Ful fi llment Center at 1-800-957-7050. Publication Description MN05002001E IT . D77A- IO Module Products Installatio ...

  • Eaton QSNAP - page 28

    Intelligent Technologies ( IT. ) QSNAP 24 Pub. No. MN05001001E February 2002 ...

  • Eaton QSNAP - page 29

    ...

  • Eaton QSNAP - page 30

    © 2002 Eaton Corporation All Rights Reserved Publication No. MN05001001E February 2002 Printed in USA Eaton Corporation Cutler -Hammer business unit 1000 Cherrington Parkway Moon T ownship, P A 15108-4312 USA tel: 1-800-525-2000 www .cutler-hammer .eaton.com Eaton’ s Cutler -Hammer Aftermarket Services • T echnical/telephone support • Reside ...

メーカー Eaton カテゴリー Network Card

Eaton QSNAPのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- QSNAPの取扱説明書
- Eatonの製品カード
- パンフレット
- またはEaton QSNAPの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Eaton QSNAPの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Eaton QSNAPの取り付け説明書、サービスマニュアル、簡易説明書、またはEaton QSNAPのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Eaton QSNAPの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Eaton QSNAPデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEaton QSNAPを使用するのを助ける技術的文書のことです。説明書は通常、全てのEaton QSNAPユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Eatonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Eaton QSNAPの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEaton QSNAPの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Eaton QSNAPに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Eaton QSNAPデバイスの基本機能を使うにあたってのヒント。 Eaton QSNAPのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Eaton QSNAPに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEaton QSNAPのメーカー/サービスへの連絡先に関する情報。

Eaton QSNAPについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもEaton QSNAPの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEaton QSNAPで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)