Directed Electronics 1401の取扱説明書

44ページ 4.36 mb
ダウンロード

ページに移動 of 44

Summary
  • Directed Electronics 1401 - page 1

    Remote Start Keyless Entr y Model 1401 Owner’ s Guide © 2011 Directed Electronics, Vista, CA G4102P 2011-03 ...

  • Directed Electronics 1401 - page 2

    ...

  • Directed Electronics 1401 - page 3

    i © 2011 Directed Electronics. All rights reserved. Contents Government regulations .................................................................................... iii W arning! Safety first ........................................................................................ iv What’ s included .......................................... ...

  • Directed Electronics 1401 - page 4

    ii © 2011 Directed Electronics. All rights reserved. Overriding the optional Starter kill ............................................................ 16 Using the remote start ...................................................................................... 17 Manual transmission vehicles ..................................................... ...

  • Directed Electronics 1401 - page 5

    iii © 2011 Directed Electronics. All rights reserved. Government regulations This device complies with Part 15 of FCC rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including inter ference that may cause undesirable operat ...

  • Directed Electronics 1401 - page 6

    iv © 2011 Directed Electronics. All rights reserved. W ar ning! Safety first The following safety warnings must be obser ved at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer . When properly installed, this system can start the vehicle via a command signal from ...

  • Directed Electronics 1401 - page 7

    v © 2011 Directed Electronics. All rights reserved. Use of this product in a manner contrar y to its intended mode of operation may result in property damage, personal injur y , or death. (1) Never remotely start the vehicle with the vehicle in gear , and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have t ...

  • Directed Electronics 1401 - page 8

    vi © 2011 Directed Electronics. All rights reserved. ...

  • Directed Electronics 1401 - page 9

    1 © 2011 Directed Electronics. All rights reserved. What’ s included • T wo five-button/1-way Supercode remotes • The control module (installed out-of-sight) • Control Center with integrated status LED and Control button • A remote start defeat toggle switch • Window decals • Y our warranty registration Impor tant ...

  • Directed Electronics 1401 - page 10

    2 © 2011 Directed Electronics. All rights reserved. System maintenance The system requires no specific maintenance. Y our remote is powered by a small coin cell lightweight 3-volt lithium batter y that lasts approximately one year under normal use. The remote uses one CR2032 cell batter y . When the batter y begins to weaken, the operating range ...

  • Directed Electronics 1401 - page 11

    3 © 2011 Directed Electronics. All rights reserved. T wo car operation Y ou can use the remote control system for two cars, with full command capabil- ity for both vehicles. T o change the car selection: • Press and hold the A U X button for 3 seconds until the amber LED blinks once or twice indicating the current vehicle: One blink: Car 1 T ...

  • Directed Electronics 1401 - page 12

    4 © 2011 Directed Electronics. All rights reserved. 1-way remote 1 3 4 5 6 2 8 7 1 2 3 4 5 6  531; ,&$ )&&,'(=6'(, %$ 77(5< &5 7 8 7 8 1 2 3 4 5 6 AU X AU X AU X Feature Description 1 T ransmit ...

  • Directed Electronics 1401 - page 13

    5 © 2011 Directed Electronics. All rights reserved. T ransmitter configuration Basic Commands Advanced Commands Function Level 1 Function Level 2 Function Level 3 Function Level 4 Button Level Direct Access A U X x 1 A U X x 2 A U X x 3 A U X x 4 A U X Lock Silent Lock A U X Unlock Silent Unlock V alet Mode Car Finder A U X Remote Start Reset Run ...

  • Directed Electronics 1401 - page 14

    6 © 2011 Directed Electronics. All rights reserved. Control Center The Control Center , typically located on the upper par t of the front windshield sends and receives commands or messages to and from your system. It consists of: • The In-vehicle system antenna, for 1-way communication to the system. • The Status LED, as a visual indicat ...

  • Directed Electronics 1401 - page 15

    7 © 2011 Directed Electronics. All rights reserved. Basic commands Lock Command : Press A U X one time to Lock. Notes: Press/hold for 1.5 seconds to lock the system and then activate the Panic output. For Panic to work, the optional horn honk feature must be connected. Unlock Command : Press A U X one time to Unlock. Remote Start Command : Press A ...

  • Directed Electronics 1401 - page 16

    8 © 2011 Directed Electronics. All rights reserved. Advanced commands: function level 1 Silent lock Command : Press A U X one- time and then press A U X . Notes : Locks the system without horn honks* Silent unlock Command : Press A U X one- time and then press A U X . Notes : Unlocks the system without horn honks* * Horn honk is an optional featur ...

  • Directed Electronics 1401 - page 17

    9 © 2011 Directed Electronics. All rights reserved. Advanced commands: function level 2 V alet mode Command : Press A U X two-times and then A U X . Notes: Prevents the system from automatically activating the Failsafe Starter Kill and locking the door passively . Timer mode Command : Press A U X two-times and then A U X . Notes : Enables or disab ...

  • Directed Electronics 1401 - page 18

    10 © 2011 Directed Electronics. All rights reserved. Advanced commands: function level 3 Car finder Command : Press A U X three-times and then A U X . Notes : The vehicle emits 1 long horn honk and the parking lights flash 10 times. Lock/Unlock cancels the parking light flashes. Smart star t Command : Press A U X three-times and then press A U ...

  • Directed Electronics 1401 - page 19

    11 © 2011 Directed Electronics. All rights reserved. Advanced commands: function level 4 Rear defogger* Command : Press A U X four times, and then A U X . (after remote start is on.) Notes : Manually turns on the defogger when remote start is on. Aux 4 Command : Press A U X four times and then press AUX . Notes : Activates or deactivates optional ...

  • Directed Electronics 1401 - page 20

    12 © 2011 Directed Electronics. All rights reserved. Using the system ➢ Locking the vehicle T o lock the vehicle, press the A U X button on the remote control. The horn (if connected) in the vehicle honks one-time, and the parking lights flash one-time. If the power door locks are connected, the doors lock and the optional Failsafe Starter Kill ...

  • Directed Electronics 1401 - page 21

    13 © 2011 Directed Electronics. All rights reserved. ➢ V alet mode Y ou can prevent your system from automatically activating the Failsafe® Star ter Kill. When the system is in V alet mode, the feature is disabled. The doors do not automatically lock. This is useful when washing or having the vehicle ser viced. T o enter or exit valet mode with ...

  • Directed Electronics 1401 - page 22

    14 © 2011 Directed Electronics. All rights reserved. Press A U X on the remote again. ➢ Configuring your remote The remote control has a menu for programming user features. Before you start make sure the keypad is unlocked. (See Button Auto Lock ) T o configure the remote user features: 1. Press and hold the A U X button on the remote for 8 se ...

  • Directed Electronics 1401 - page 23

    15 © 2011 Directed Electronics. All rights reserved. the A U X button, then press and release while the LED is flashing to continue to perform Car Select. Once the car is selected a command can be per formed by pressing one of the command buttons. ➢ Remote Pairing Remote pairing is a process where the remote, and the in-vehicle system learn the ...

  • Directed Electronics 1401 - page 24

    16 © 2011 Directed Electronics. All rights reserved. 1.5 seconds. The transmit LED turns off. ➢ Overriding the optional Starter kill T o bypass the optional Star ter kill without a remote control: Use the button on the Control Center (see diagram below) to bypass the system. Y ou can bypass the system only if you have the vehicle key . T o check ...

  • Directed Electronics 1401 - page 25

    17 © 2011 Directed Electronics. All rights reserved. Using the remote star t Read this user guide, including the W arnings section at the beginning of this guide before using the remote start . Ensure that the vehicle is parked in an open area, not in a garage. T o use your remote star t to pre-warm or pre-cool your vehicle, remember to set the cl ...

  • Directed Electronics 1401 - page 26

    18 © 2011 Directed Electronics. All rights reserved. ➢ Manual transmission vehicles When installed into a manual transmission vehicle, the system requires that the MTS mode is properly set when parking. If MTS mode is not properly set or is defeated after being properly set the system will not start the engine. T o set manual transmission mode w ...

  • Directed Electronics 1401 - page 27

    19 © 2011 Directed Electronics. All rights reserved. 2. Insert the ignition key and turn it to the On position. 3. Now , step on the brake. The remote start tur ns off. The vehicle is ready to drive. ➢ Timer mode This unit can be programmed to start and run the engine ever y three hours, for a maximum of six cycles. The engine will run for the p ...

  • Directed Electronics 1401 - page 28

    20 © 2011 Directed Electronics. All rights reserved. T o exit timer mode without the transmitter: 1. Make sure the remote start system is not operating the engine. 2. T ur n the ignition on. Timer Mode is exited and the parking lights flash slowly four times. Note: Y our authorized Directed dealer using the Bitwriter® programming tool can change ...

  • Directed Electronics 1401 - page 29

    21 © 2011 Directed Electronics. All rights reserved. remains running for the programmed runtime. (The remote start feature is still enabled). Y ou can still remote star t the vehicle after the turbo timer has timed out and shut Off the vehicle. For safety reasons, if a door is opened (while the system is Locked or Unlocked) while you are away , th ...

  • Directed Electronics 1401 - page 30

    22 © 2011 Directed Electronics. All rights reserved. Use one of the below methods to exit Smart Star t mode: • Perform the same steps you followed to activate Smar t Start mode • T ur n the ignition On • Press the brake pedal The parking lights flash 5 times slowly to confirm the remote has exited Smart Start mode. ➢ T urning on ...

  • Directed Electronics 1401 - page 31

    23 © 2011 Directed Electronics. All rights reserved. Note : T o use Pit Stop mode with a manual transmission, open the door when going into MTS mode. The parking lights flash five-times to confirm entr y into Pit Stop mode. After you exit the vehicle you can lock the system with the remote and the car remains running. If the vehicle shuts down ...

  • Directed Electronics 1401 - page 32

    24 © 2011 Directed Electronics. All rights reserved. Safety features This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components. ➢ Optional starter anti-grind circuitr y Whenever the vehicle is remote started, advanced anti-grind circuitr y prevents the ...

  • Directed Electronics 1401 - page 33

    25 © 2011 Directed Electronics. All rights reserved. Diagnostics The microprocessor at the heart of the system is constantly monitoring the switches that are connected to the main unit. ➢ Locking If the system is locked at the same time that the door input is active, you will hear one horn honk to indicate locking, and then a second horn honk to ...

  • Directed Electronics 1401 - page 34

    26 © 2011 Directed Electronics. All rights reserved. Owner recognition Owner recognition lets up to four users of the system have unique settings to meet their specific needs. It is almost like having four separate systems in your vehicle, one for each user . This feature is only available to authorized dealers using the Bitwriter programming too ...

  • Directed Electronics 1401 - page 35

    27 © 2011 Directed Electronics. All rights reserved. Programming options Y our system has many custom programmable options. Some may require instal- lation labor . Ask your authorized dealer for details. The following is a list of the programmable options, with the factor y settings in Bold . • Active locking (remote only) and passive locking ...

  • Directed Electronics 1401 - page 36

    28 © 2011 Directed Electronics. All rights reserved. Convenience expansions Listed below are some of the expansion options available. Please consult your dealer for a complete explanation of all the options available to you. Power T runk Release: The accessory output of the system can operate a factor y power release for the vehicle’ s trunk or ...

  • Directed Electronics 1401 - page 37

    29 © 2011 Directed Electronics. All rights reserved. Glossar y of ter ms Control Center: The Control Center contains the system’ s radio-frequency antenna, the Control button, and the Status LED. For maximum remote-control range, the Control Center is usually located at the top of the windshield, centered near the rear-view mirror . Control Modu ...

  • Directed Electronics 1401 - page 38

    ...

  • Directed Electronics 1401 - page 39

    31 © 2011 Directed Electronics. All rights reserved. Quick reference guide • Locking T o lock press A U X for one second. The doors lock. The LED on the Control Center flashes and the horn honks one time. (if connected). The parking lights flash once to confirm locking. • Unlocking T o unlock press A U X . The doors unlock, and the ho ...

  • Directed Electronics 1401 - page 40

    32 © 2011 Directed Electronics. All rights reserved. • Remote Start Press A U X . The parking lights turns on (if connected). The vehicle starts and runs for the programmed duration. • Rear Defogger* Press A U X four-times, and then press A U X (only after remote start is On.) The parking lights flash 4 times confirming activation of t ...

  • Directed Electronics 1401 - page 41

    33 © 2011 Directed Electronics. All rights reserved. Limited lifetime consumer warranty Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace (at Directed’ s election) with a comparable reconditioned model any Directed unit (hereafter the “unit”), excluding without limitation the siren, the remote tra ...

  • Directed Electronics 1401 - page 42

    34 © 2011 Directed Electronics. All rights reserved. WITHOUT LIMIT A TION, LIABILITY FOR THEFT , DAMAGE AND/OR V ANDALISM. THIS W ARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOV AL OR REINST ALLA TION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOL VING DIRECTED OR ITS SUBSIDIARY , THE VEN ...

  • Directed Electronics 1401 - page 43

    ...

  • Directed Electronics 1401 - page 44

    G4102P 2011-03 Vista, CA 92081 www .directed.com © 2011 Directed Electronics—All rights reser ved The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 1 ...

メーカー Directed Electronics カテゴリー Remote Starter

Directed Electronics 1401のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 1401の取扱説明書
- Directed Electronicsの製品カード
- パンフレット
- またはDirected Electronics 1401の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Directed Electronics 1401の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Directed Electronics 1401の取り付け説明書、サービスマニュアル、簡易説明書、またはDirected Electronics 1401のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Directed Electronics 1401の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Directed Electronics 1401デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDirected Electronics 1401を使用するのを助ける技術的文書のことです。説明書は通常、全てのDirected Electronics 1401ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Directed Electronicsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Directed Electronics 1401の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDirected Electronics 1401の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Directed Electronics 1401に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Directed Electronics 1401デバイスの基本機能を使うにあたってのヒント。 Directed Electronics 1401のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Directed Electronics 1401に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDirected Electronics 1401のメーカー/サービスへの連絡先に関する情報。

Directed Electronics 1401についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDirected Electronics 1401の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDirected Electronics 1401で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)