-
Maytag MLG32PDA - page 1
12/29/97GS/tf ADC Part No. 113030 Installation/Operators Manual MLG32PDA 30 lb. Stacked Model R ET AIN T HESE I NSTRUCTIONS I N A S AFE P LACE F OR F UTURE R EFERENCE W ARNING: For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or death. Do not ...
-
Maytag MLG32PDA - page 2
For replacement parts, contact the distributor from which the dryer was purchased or contact: Maytag 403 W est Fourth St North Newton, Iowa 50208 (515) 792-7000 IMPOR T ANT NOTE T O PURCHASER Information must be obtained from your local gas supplier on the instructions to be followed if the user smells gas. These instructions must be posted i ...
-
Maytag MLG32PDA - page 3
IMPOR T ANT YOU MUST DISCONNECT and LOCKOUT THE ELECTRIC SUPPL Y and THE GAS SUPPL Y or THE STEAM SUPPL Y BEFORE ANY COVERS or GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INST ALLA TION, or TESTING OF ANY EQUIPMENT per OSHA (Occupational Safety and Health Administration) ST ANDARDS. W ARNING The dryer must never be ...
-
Maytag MLG32PDA - page 4
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE V APOR AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE . FOR YOUR SAFETY DO NOT DR Y MOP HEADS IN THE DR YER. DO NOT USE DR YER IN THE PRESENCE OF DR Y CLEANING FUMES. IMPOR T ANT PLEASE OBSER V E ALL SAFETY PRECAUTIONS displayed on the equipment and/or specified in the installation/operato ...
-
Maytag MLG32PDA - page 5
T able of Contents SECTION I IMPOR T ANT INFORMA TION ............................................................................... 3 A. RECEIVING and HANDLING ....................................................................................................... 3 B . SAFETY PRECAUTIONS ........................................................... ...
-
Maytag MLG32PDA - page 6
SECTION VII ROUTINE MAINTENANCE .................................................................................. 28 A. CLEANING .................................................................................................................................. 28 B. ADJUSTMENTS ....................................................................... ...
-
Maytag MLG32PDA - page 7
3 SECTION I IMPOR T ANT INFORMA TION A. RECEIVING and HANDLING The dryer is shipped in a protective stretch wrap cover with protective cardboard corners and top cover (or optional box) as a means of preventing damage in transit. Upon delivery, the dryer and/or packaging, and wooden skid should be visually inspected for shipping damage. If any damag ...
-
Maytag MLG32PDA - page 8
4 B. SAFETY PRECAUTIONS WARNING: For your safety, the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury, or loss of life. W ARNING: The dryer must never be operated with any of the back guards, outer tops, or service panels removed. PERSONAL INJUR Y or FIRE COULD RES ...
-
Maytag MLG32PDA - page 9
5 WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, or similarly textured rubber-like materials. Drying in a heated basket (tumbler) may damage plastics or rubber and also may be a fire hazard. 7 . A program should be established for the inspection and cleaning of lint in the heating unit area, exhaust duct wor ...
-
Maytag MLG32PDA - page 10
6 SECTION II SPECIFICA TIONS ...
-
Maytag MLG32PDA - page 11
7 M L G 32P D A M a xi mu m C a p a c i t y ( d r y w e ight ) 3 0 lb s B a sket (T u m bl er ) D i am et er 27- 1/ 4" B a sket (T u m b l er) Dept h 30" B a sket (T u m b l er ) V o l u m e ( p e r Bask e t) 10. 1 c u .f t . B asket ( T u m bl er ) Mot o r (2 Pl aces ) 1/ 2 H P D oor O pen i n g - D i a m et er ( 2 P l a ces) 21- 1/ 2&qu ...
-
Maytag MLG32PDA - page 12
8 SECTION III INST ALLA TION PROCEDURES Installation should be performed by competent technicians in accordance with local and state codes. In the absence of these codes, the installation must conform to applicable American National Standards: National Fuel Gas Code ANSI.Z223.1-LATEST EDITION and/or National Electric Code ANSI/NFPA NO. 70-LATEST ED ...
-
Maytag MLG32PDA - page 13
9 B. LOCATION OF THE DRYER Before installing the dryer, be sure the location conforms to local codes and ordinances. In the absence of such codes or ordinances the location must conform with the National Fuel Gas Code ANSI.Z223.1-LATEST EDITION, or in CANADA, the Canadian Installation Codes CAN/CGA-B149.1-M91 (Natural Gas) or CAN/ CGA-B149.2-M91 (L ...
-
Maytag MLG32PDA - page 14
10 C. DRYER ENCLOSURE REQUIREMENTS Bulkheads and partitions should be made of noncombustible materials and must be located a minimum of twelve (12) inches (18-inches or more is recommended for ease of installation, maintenance , and service) above the dryer outer top, except along the front of the dryer which may be closed in if desired. NOTE: Even ...
-
Maytag MLG32PDA - page 15
11 IMPORTANT: Make-up air openings SHOULD NOT be located near duct work exhaust outlets. If make-up air opening(s) are too close to the exhaust outlet, lint and fumes may be drawn back into the dryer area through these openings. NOTE: Component failure due to dry cleaning fumes will VOID THE WARRANTY. ...
-
Maytag MLG32PDA - page 16
12 E. EXHAUST REQUIREMENTS Exhaust duct work should be designed and installed by a qualified professional. Improperly sized duct work will create excessive back pressure which results in slow drying, increased use of energy, overheating of the dryer, and shutdown of the burner by the airflow (sail) switches, burner hi-limits, or basket (tumbler) hi ...
-
Maytag MLG32PDA - page 17
13 NOTE: Where the exhaust duct passes through a wall, ceiling, or roof made of combustible materials, the opening must be 2-inches lar ger (all the way around) than the duct. The duct must be centered within this opening. T o protect the outside end of the horizontal duct work from the weather , a 90º elbow bent downward should be installed where ...
-
Maytag MLG32PDA - page 18
14 2. MUL TIPLE DR YER (Common) VENTING If it is not feasible to provide separate exhaust ducts for each dryer , ducts from individual dryers may be channeled into a "common main duct." The individual ducts should enter the bottom or side of the main duct at an angle not more than 45º in the direction of the airflow . The main duct shoul ...
-
Maytag MLG32PDA - page 19
15 IM POR T ANT : DO NOT use screens or caps on the outside opening of exhaust duct work. ...
-
Maytag MLG32PDA - page 20
16 F. ELECTRICAL INFORMATION 1. Electrical Requirements It is your responsibility to have ALL electrical connections made by a properly licensed and competent electrician to assure that the electrical installation is adequate and conforms with local and state regulations or codes. In the absence of such codes, ALL electrical connections, materials, ...
-
Maytag MLG32PDA - page 21
17 3. Electrical Connections A wire diagram is located on the inside of the control (service) box for connection data. a. Single-Phase (1Ø) Hookup The electrical connections on ALL single-phase (1Ø) dryers are made into the junction box located at the upper rear of the dryer . A separate circuit serving each dryer tumbler must be provided. Sin g ...
-
Maytag MLG32PDA - page 22
18 * AWG Stranded Type Wire ... for individual lengths less than 100 feet. NOTE: Contact factory for electrical information not listed. NOTE: Manufacturer reserves the right to make changes in specifications at any time without notice or obligation. E LE CTR IC S E R VICE S P E CI FICAT IO N S (p e r T u m b le r ) A se p e ra te c i rcui t b r eak ...
-
Maytag MLG32PDA - page 23
19 G. GAS INFORMATION It is your responsibility to have ALL plumbing connections made by a qualified professional to assure that the gas plumbing installation is adequate and conforms with local and state regulations or codes. In the absence of such codes, ALL plumbing connections, materials, and workmanship must conform to the applicable requireme ...
-
Maytag MLG32PDA - page 24
20 The input ratings shown on the dryer data label are for elevations up to 2,000 feet, unless elevation requirements of over 2,000 feet were specified at the time the dryer order was placed with the factory . The adjustment or conversion of dryers in the field for elevations over 2,000 feet are made by changing each burner orifice. If this convers ...
-
Maytag MLG32PDA - page 25
21 The dryer is provided with a 3/4" N.P .T . inlet pipe connection at the upper right hand corner (when viewed from the rear) of each dryer . It is recommended that a gas shutof f valve be provided to the gas supply line of each dryer for ease of servicing. The size of the main gas supply line (header) will vary depending on the distance this ...
-
Maytag MLG32PDA - page 26
22 W ARNING: T est ALL connections for leaks by brushing on a soapy water solution (liquid detergent works well). NEVER TEST FOR LEAKS WITH A FLAME!!! It is important that gas pressure regulators meet applicable pressure requirements and that gas meters be rated for the total amount of appliance Btu's being supplied. H. PREPARATION FOR OPERATI ...
-
Maytag MLG32PDA - page 27
23 3) Start the dryer by pressing the desired fabric setting. After the cycle is started, drying time will count down whether the door is closed or open. NOTE: The dryer can be stopped at any time by opening the main door. To restart dryer, shut the main door and press desired fabric setting. 4) Open main door to stop the dryer, and change to a dif ...
-
Maytag MLG32PDA - page 28
24 3 . Make a complete operational check of ALL the operating controls to insure that the timing is correct and that the temperatures are set properly . 4 . Make a complete operational check of ALL safety-related circuits (i.e., door switches, hi-limit thermostats, sail switches, basket (tumbler) safety thermostats, etc.). NOTE: The sail switch can ...
-
Maytag MLG32PDA - page 29
25 SECTION IV OPERA TING INSTRUCTIONS A. STARTING THE DRYER The dryer is available for use when the appropriate side of the microprocessor display reads "0 minutes" and the amount needed to start the dryer (i.e., "25"). Once the load has been put into the dryer and the main door is closed, start the dryer as follows: 1 . Insert ...
-
Maytag MLG32PDA - page 30
26 SECTION V SER VICE/P AR TS INFORMA TION A. SERVICE 1 . Only properly licensed or trained technicians should service the dryer . If service is required, contact the distributor from whom the equipment was purchased. If the distributor cannot be contacted or is unknown, contact Maytag for a distributor in your area. NOTE: When contacting the Mayta ...
-
Maytag MLG32PDA - page 31
27 SECTION VI W ARRANTY INFORMA TION A. RETURNING WARRANTY CARD(S) 1. Before any dryer leaves the manufacturer , a warranty card is affixed to the glass of the main door . These warranty cards are intended to serve the customer as a record installation date of that specific dryer so as to extend the customer's warranty period. IM POR T ANT : A ...
-
Maytag MLG32PDA - page 32
28 SECTION VII ROUTINE MAINTENANCE A. CLEANING A program and/or schedule should be established for periodic inspection, cleaning, and removal of lint from various areas of the dryer , as well as throughout the duct work system. The frequency of cleaning can best be determined from experience at each location. Maximum operating efficiency is depende ...
-
Maytag MLG32PDA - page 33
29 90 DAYS Remove lint from the motor air vents and surrounding area. IM POR T ANT : Lint accumulation will restrict the airflow over the motor(s), causing overheating and irreparable motor damage. Motor failure due to lint accumulation will VOID THE W ARRANTY . Remove lint accumulation from around the openings in the dryer's back panels. Remo ...
-
Maytag MLG32PDA - page 34
B. ADJUSTMENTS 7 DAYS AFTER INSTALLATION and EVERY 6 MONTHS THEREAFTER Inspect bolts, nuts, screws (bearing set screws), non-permanent gas connections (unions, shut-off valves, orifices, etc.), electrical terminations, and grounding connections. Motor and drive belts should be examined. A cracked or seriously frayed belt(s) should be replaced. Tigh ...
-
Maytag MLG32PDA - page 35
Part No. 113030 1 - 01/13/98-500 2* 05/06/98-500 3 - 05/19/98-500 ...
Maytag MLG32PDAについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもMaytag MLG32PDAの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMaytag MLG32PDAで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。