-
Harbor Freight Tools 04041 - page 1
FRAMING NAILER 21 DEGREE ANGLED / 10 GA UGE Model 04041 ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yright © 2004 by Harbor F reight T ools ® . All rights reser v ed. No por tion of this manual or an y ar twor k contained herein ma y be reproduced in ...
-
Harbor Freight Tools 04041 - page 2
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 2 PR ODUCT SPECIFICA TIONS Save This Manual Safety W arnings and Precautions W ARNING: When using tool, basic saf ety precautions should alwa ys be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this tool! 1. Keep work area ...
-
Harbor Freight Tools 04041 - page 3
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 3 REV 01/04 8. Use eye and ear protection . Always wear ANSI approved impact safety goggles and appropriate hear ing protection. Wear a full f ace shield if you are producing metal filings or wood chips. W ear an ANSI approv ed dust mask or respirator when working around metal, wood ...
-
Harbor Freight Tools 04041 - page 4
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 4 18. Use proper size and type extension cord . If an extension cord is required, it must be of the proper size and type to supply the correct current to the compressor without heating up . Otherwise, the e xtension cord could melt and catch fire, or cause electri- cal damage to the ...
-
Harbor Freight Tools 04041 - page 5
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 5 UNP A CKING When unpacking, chec k to make sure all the par ts shown on the P ar ts List on pa g e 11 are included. If any par ts are missing or broken, please call Harbor F reight T ools at the number shown on the cover of this manual as soon as possible. OPERA TION Nailer/ 1/4? ...
-
Harbor Freight Tools 04041 - page 6
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 6 T esting The Single Sequential Safety T rip Mechanism W arning: Even though the nailer should be empty during this procedure, AL W A YS point the Nailer at a piece of scrap wood when testing. 1 . The Nailer should not fire if the nose is not depressed against the workpiece. This t ...
-
Harbor Freight Tools 04041 - page 7
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 7 OPERA TION NO TE: F or additional references to the par ts listed belo w , ref er to the Assemb ly Diagram on page 11. REV 01/04 3 . Orient a strip of nails with the points down, and drop the strip of nails into the Magazine (par t #71). (See Figure C.) 4 . Slide the strip of nail ...
-
Harbor Freight Tools 04041 - page 8
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 8 EXHA UST CO VER (#4) NAILS (10 GA UGE) (2-3/16” T O 3-1/2” LONG) FEEDER SHOE (#52) NOSE (#29) BRA CKET A (#35) SAFETY (38) TRIGGER (#44) FIGURE B NOSE (#29) REV 01/04 T o Adjust The Depth T o Which A Nail Is Driven 1 . The depth to which a nail is driven is controlled b y the ...
-
Harbor Freight Tools 04041 - page 9
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 9 SAFETY (#38) RUBBER CO VER (39) SCREW (#37) FIGURE C REV 01/04 An ytime an y maintenance or repair s are done (inc luding c learing jams), FIRST : 1 . Disconnect the Nailer from the air hose. 2 . Empty the Magazine (71) completely . 3 . Attempt to fire the Nailer into a piece of s ...
-
Harbor Freight Tools 04041 - page 10
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 10 INSPECTION, MAINTENANCE, AND CLEANING 1. CA UTION: Alw a ys disconnect the F r aming Nailer from its compressed air supply source before performing any inspection, maintenance, or cleaning. 2. BEFORE EA CH USE, inspect the general condition of the F raming Nailer . Check for loos ...
-
Harbor Freight Tools 04041 - page 11
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 11 ...
-
Harbor Freight Tools 04041 - page 12
SKU 04041 For Technical Questions, Please Call 1-800-444-3353 Page 12 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIB UT OR HAS PRO VIDED THE P ARTS LIST AND ASSEMBL Y DIAGRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF ACTURER OR DISTRIBUT OR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND TO THE BUYER ...
Harbor Freight Tools 04041についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHarbor Freight Tools 04041の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 04041で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。