ページに移動 of 60
Owner's Operator And Maintenance Manual ® Terminator SS DEALER: THIS MANUAL MUST BE GIVEN TO THE USER OF THE WHEELCHAIR. USER: BEFORE USING THIS WHEELCHAIR, READ THIS MANUAL AND SAVE FOR FUTURE REFERENCE. ...
Terminator SS 2 Part No. 1052712 Rev D SPECIAL NOTES WARNING/CAUTION notices as used in this manual apply to hazards or unsafe practices which could result in personal injury or property damage. NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. As a manufacturer of wheelchairs, Invacare endeavors to supply a ...
Part No. 1052712 Rev D 3 Terminator SS TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS SPECIAL NOTES ................................................................................ 2 SPECIFICATIONS .............................................................................. 5 SECTION 1 - GENERA L GUIDELINES ............................. ...
Terminator SS 4 Part No. 1052712 Rev D TABLE OF CONTENTS TABLE OF CONTENTS SECTION 6 - FOOT REST/ANTI-TIPPER ............................................. 46 ADJUSTING/REPLACING STANDARD FOOTREST ...................................................................... 46 INSTALLING/ADJUSTING OPTIONAL CLAMP ON RAISED FOOTREST ...................... ...
Part No. 1052712 Rev D 5 Terminator SS SPECIFICATIONS SPECIFICATIONS NOTE: All specifications are approximate. SPECIFICATIONS TERMINATOR SS Frame: Rigid - with Rear Suspension - 4130 Chrome-moly Seat Width: 12-20-inches - Outside to Outside of SEAT FRAME in 1-inch increments. Seat Depth: 14 to 18-inches (15-inch Standard) Seat-to-Floor: Front - ...
Terminator SS 6 Part No. 1052712 Rev D Section 1 - General Guidelines - includes the following: Stability Operating Information Tire Pressure and Information Weight Training Weight Limitation Safety/Handling of Wheelchairs GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES STABILITY STABILITY STABILITY STABILITY STABILITY STABILITY WARNING The posi ...
Part No. 1052712 Rev D 7 Terminator SS WARNING DO NOT tip the wheelchair without assistance. DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur. Before attempting to transfer in or out of the wheelchair, every precaution should be taken to reduce the gap distance. Turn both casters toward the object you ...
Terminator SS 8 Part No. 1052712 Rev D GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES TIRE PRESSURE AND INFORMATION WARNING DO NOT use your wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT overinflate the tires. Failure to follow these suggestions may cause the tire to explode and cause bodily harm. The recommended tire pressu ...
Part No. 1052712 Rev D 9 Terminator SS SAFETY/HANDLING OF WHEELCHAIRS Safety and Handling of the wheelchair requires the close attention of the wheelchair user as well as the assistant. This manual points out the most common procedures and techniques involved in the safe operation and maintenance of the wheelchair. It is important to pract ...
Terminator SS 10 Part No. 1052712 Rev D GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES WARNING Do not attempt to lift a wheelchair by lifting on any removable (detachable) parts. Lifting by means of any removable (detachable) parts of a wheelchair may result in injury to the user or damage to the wheelchair. Also, be aware of any removable (det ...
Part No. 1052712 Rev D 11 Terminator SS Reaching, Leaning and Bending - Forward. Position the front casters so that they are extended as far forward as possible and engage wheel locks. WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees. Reaching, Lean ...
Terminator SS 12 Part No. 1052712 Rev D GENERAL GUIDELINES SECTION 1 GENERAL GUIDELINES TIPPING - CURBS: WARNING Invacare does not recommend that sport wheelchairs be used where traversing curbs present an obstacle. Possible injury to occupant and/or assistant(s) can occur. Transfer to an everyday use wheelchair is recommended if any such obstac ...
Part No. 1052712 Rev D 13 Terminator SS Follow this procedure for moving the wheelchair between floors when an elevator is NOT available: 1. If equipped, turn the anti-tippers UP. Refer to SECTION 6 in this manual. 2. After the wheelchair has been tilted back to the balance point, one assistant (in the rear) backs the wheelchair up against the f ...
Terminator SS 14 Part No. 1052712 Rev D SAFETY INSPECTION SECTION 2 SAFETY INSPECTION Section 2 - Safety Inspection - includes the following: Safety Inspection Checklist Troubleshooting Maintenance NOTE: Every six (6) months, take your wheelchair to a qualified technician for a thorough inspection and servicing. Regular cleaning will reveal loos ...
Part No. 1052712 Rev D 15 Terminator SS TROUBLESHOOTING SAFETY INSPECTION SECTION 2 MAINTENANCE MAINTENANCE SAFETY PRECAUTIONS WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. CAUTION DO NOT overtighten hardware attaching to the frame. ...
Terminator SS 16 Part No. 1052712 Rev D CAUTION As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced if damaged. 5. The wheels, casters and tires should be checked periodically for cracks and wear, and should be replaced when necessary. Contact a qualified technician or Invacare cus ...
Part No. 1052712 Rev D 17 Terminator SS SECTION 3 BACK WARNING ALWAYS perform this procedure in the presence of an assistant. The position of the footrest, camber tube, back angle, the tautness of the back upholstery as well as the user's condition are directly related to the wheelchairs stability. Any change to one (1) or any combination o ...
Terminator SS 18 Part No. 1052712 Rev D BACK SECTION 3 FIGURE 1 - BACK ANGLE ADJUSTMENT BACK 73° BACK ANGLE TO SEAT RAIL 77° BACK ANGLE TO SEAT RAIL 84° BACK ANGLE TO SEAT RAIL 94° BACK ANGLE TO SEAT RAIL 85° BACK ANGLE TO SEAT RAIL 90° BACK ANGLE TO SEAT RAIL Back Cane Indexing Notch Cam Back Angle Bracket Seat Rail TOP Hex Screw and Lock ...
Part No. 1052712 Rev D 19 Terminator SS FOLDING/UNFOLDING THE BACK (FIGURE 2) NOTE: This procedure is for folding back chairs only. WARNING Back MUST be locked securely in place before using the chair. 1. Lift up on the back and pull towards the rear of the chair until it locks into place. 2. To fold the back, pull up on the black nylon cord and ...
Terminator SS 20 Part No. 1052712 Rev D BACK SECTION 3 BACK Replacing Top End Back Upholstery. 1. Unlatch the two (2) fastening flaps that secure the top of the back upholstery to the back canes. 2. Remove the fastening flaps from the back canes by lifting straight up. 3. Remove the seat cushion. 4. Separate the bottom of the back upholstery fro ...
Part No. 1052712 Rev D 21 Terminator SS CUSTOM MANUAL ADJUSTABLE TENSION BACK UPHOLSTERY (FIGURE 4) The Adjustable Tension Straps. The straps can be adjusted at various levels of tension to accommodate individual end-users. The bottom two (2) straps can be adjusted tightly to support and/or assist the extensor muscles. The Back Upholstery Cover. ...
Terminator SS 22 Part No. 1052712 Rev D WARNING After the adjustable tension back upholstery has been positioned to the end-users individual needs, the fastening straps MUST be securely fastened BEFORE applying the back upholstery cover. The adjustable back should be checked whenever entering the wheelchair to ensure that the fastening straps ar ...
Part No. 1052712 Rev D 23 Terminator SS BACK HEIGHT ADJUSTMENT (ADJUSTABLE BACKS ONLY) (FIGURE 5 ) NOTE: Observe the tautness of the back upholstery for reinstallation. 1. Unlatch the two (2) fastening flaps that secure the top of the back upholstery to the back canes and remove from the back canes. WARNING Push pin MUST be protruding through ho ...
Terminator SS 24 Part No. 1052712 Rev D SEAT SECTION 4 WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. REPLACING TOP END SEAT UPHOLSTERY (FIGURE 1) WARNING The seat upholstery and/or cushion MUST be cleaned regularly and/or replaced i ...
Part No. 1052712 Rev D 25 Terminator SS REPLACING CUSTOM MANUAL SCREW ON SEAT UPHOLSTERY (FIGURE 2) 1. Remove the seat cushion from the wheelchair. 2. Remove the twelve (12) phillips screws that secure the existing seat upholstery to the seat frame. 3. Remove the existing seat upholstery. FIGURE 2 - REPLACING CUSTOM MANUAL SCREW ON SEAT UPHOLSTE ...
Terminator SS 26 Part No. 1052712 Rev D WHEELS SECTION 5 WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. REMOVING/INSTALLING REAR WHEELS (FIGURE 1) CAUTION Changing the size of the rear wheels can affect the performance of the wheelch ...
Part No. 1052712 Rev D 27 Terminator SS ADJUSTING QUICK-RELEASE AXLES (FIGURE 2) 1. Remove rear wheel and quick-release axle from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. 2. Depress detent pin in the quick-release axle and slide axle through the wheel hub. 3. Release detent pin ensuring that the loc ...
Terminator SS 28 Part No. 1052712 Rev D INSTALLING QUAD-RELEASE AXLES (FIGURE 3) 1. Remove rear wheel and the existing quick-release axle from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. 2. Remove existing quick-release axle from rear wheel. 3. Insert new quad-release axle through rear wheel hub. 4. Sl ...
Part No. 1052712 Rev D 29 Terminator SS 4. Tighten the locking screw. 5. Reinstall the rear wheel and quad-release axle onto the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. 6. Flip the handle of the quad-release axle down to release the detent pin ensuring that the locking pins are fully released. 7. Repea ...
Terminator SS 30 Part No. 1052712 Rev D REPAIRING/REPLACING REAR WHEEL, TIRE/TUBE WARNING Replacement of the tire or tube MUST be performed by a qualified technician. CAUTION Changing the size of the rear wheels can affect the performance of the wheelchair. Contact Invacare at the numbers on the back cover BEFORE performing this procedure. NOTE: ...
Part No. 1052712 Rev D 31 Terminator SS WHEELS SECTION 5 RECEIVER TUBE CLAMPS 1. Perform one (1) of the following to open a receiver tube clamp: A. QUICK RELEASE LEVERS - Pull the quick release levers on the receiver tube clamps to the open position. B. STANDARD RECEIVER TUBE CLAMPS - Loosen, but do not remove the hex screws and locknuts on the ...
Terminator SS 32 Part No. 1052712 Rev D ADJUSTING REAR WHEEL CAMBER CAMBER TUBE 2000 The axle tube must be replaced to change the camber. Refer to REPLACING AXLE TUBE in this section of the manual. A4 CAMBER SYSTEM (FIGURE 7) NOTE: Perform this procedure to one (1) side of the wheelchair at a time for ease of adjustment. 1. Open the camber clamp ...
Part No. 1052712 Rev D 33 Terminator SS WHEELS SECTION 5 WHEELS 10. Reinstall rear wheel to the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the manual. 11. Adjust toe in/toe out of wheelchair. Refer to ADJUSTING TOE IN/TOE OUT in this section of the manual. DETERMINING TOE IN/TOE OUT (FIGURES 8 AND 9) 1. Inflate all p ...
Terminator SS 34 Part No. 1052712 Rev D WHEELS SECTION 5 WHEELS ADJUSTING TOE IN/TOE OUT CAMBER TUBE 2000 (FIGURE 10) 1. Open the camber clamps. Refer to OPENING/CLOSING CLAMPS in this section of the manual. 2. Slowly rotate the camber tube in either direction until the rear wheels are approximately in a straight line. 3. Close the camber clamps ...
Part No. 1052712 Rev D 35 Terminator SS Axle Tube - Rotates Up and Down FIGURE 11 - ADJUSTING TOE IN/TOE OUT - A4 CAMBER SYSTEM - COURSE ADJUSTMENT Adjustment Ring Stop - Not touching camber clamp Stop - In position for one (1) camber, touching camber clamp Adjustment Ring Adjustment Ring Phillips Screw Stop - In position for one (1) camber, tou ...
Terminator SS 36 Part No. 1052712 Rev D FIGURE 12 - ADJUSTING TOE IN/TOE OUT - A4 CAMBER SYSTEM - FINE ADJUSTMENT Adjustment Ring Stop - In position for one (1) camber, touching camber clamp Stop - Not touching camber clamp Adjustment Ring Phillips Screw Camber Clamp Stop - Not touching camber clamp Adjustment Ring Camber Clamp Adjustment Ring S ...
Part No. 1052712 Rev D 37 Terminator SS FIGURE 13 - ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) Indexing Marks (MUST be set to Same Mark on BOTH Suspension Tubes) NEVER OPERATE THE WHEELCHAIR WITH BOTH ENDS OF THE INDEXING TAPE SHOWING. WHEELS SECTION 5 ADJUSTING WHEELBASE LENGTH (ADJUSTING CENTER OF GRAVITY) (FIGURE 13) WARNING ALW ...
Terminator SS 38 Part No. 1052712 Rev D ADJUSTING WHEELBASE WIDTH NOTE: Perform this procedure one (1) side of the wheelchair at a time for ease of adjustment. CAMBER TUBE 2000 (FIGURE 14) NOTE: The wheelbase width can be increased/decreased by 1-inch. 1. Remove the rear wheels. Refer to REMOVING/INSTALLING REAR WHEELS in this section of the man ...
Part No. 1052712 Rev D 39 Terminator SS REPLACING AXLE TUBE (FIGURE 16) NOTE: The camber bar is always mounted to the BOTTOM of the wheelchair frame. NOTE: There is no need to remove the two (2) camber clamps when replacing the axle tube. 1. A4 CAMBER SYSTEM ONLY - Note the position of the camber inserts so they can be installed at the same posi ...
Terminator SS 40 Part No. 1052712 Rev D WHEELS SECTION 5 WHEELS 6. Pull the existing axle tube through one (1) of the camber clamps. 7. A4 CAMBER SYSTEM ONLY - Remove toe adjustment rings from the existing axle tube. 8. Pull the existing axle tube through the other camber clamp and remove from the wheelchair. 9. Slide the new axle tube through o ...
Part No. 1052712 Rev D 41 Terminator SS Place "L" Square Here 90° Angle Flat Edge of Camber Tube Ground/ Floor FIGURE 17 - ADJUSTING THE AXLE TUBE - CAMBER TUBE 2000 CAUTION A4 CAMBER SYSTEM ONLY - DO NOT close the quick-release levers or tighten the hex screws and locknuts without camber inserts in the axle tube. Damage to the axle t ...
Terminator SS 42 Part No. 1052712 Rev D WHEELS SECTION 5 WHEELS 10. Reposition the camber inserts to the highest degree of camber. Refer to ADJUSTING REAR WHEEL CAMBER in this section of the manual. 11. Repeat STEP 3. 12. Close the LEFT camber clamp. Refer to OPENING/CLOSING CLAMPS in this section of the manual. 13. Rotate the RIGHT toe adjustme ...
Part No. 1052712 Rev D 43 Terminator SS REPLACING/ADJUSTING CASTERS (FIGURE 19) CAUTION Changing the size of and/or repositioning the front casters can affect the performance of the wheelchair. Contact Invacare at the telephone numbers on the back of this manual BEFORE performing this procedure. 1. Remove the bolt and locknut that secure the fro ...
Terminator SS 44 Part No. 1052712 Rev D ADJUSTING FRONT CASTER HEIGHT (FIGURE 20) CAUTION Changing the height of the front casters can affect the performance of the wheelchair. Contact Invacare at the telephone numbers on the back of this manual BEFORE performing this procedure. NOTE: When changing a rear wheel/front caster to a different size a ...
Part No. 1052712 Rev D 45 Terminator SS WHEELS SECTION 5 WHEEL LOCK ADJUSTMENT/REPLACEMENT (FIGURE 2 1) NOTE: Invacare recommends LOW mount wheel locks when engaging in any contact sport. NOTE: Before adjusting or replacing the High/Low mount wheel locks, ensure that the tires are inflated to the recommended psi on the sidewall of the tire. 1. L ...
Terminator SS 46 Part No. 1052712 Rev D SECTION 6 FOOTREST/ANTI-TIPPER FOOTREST / ANTI-TIPPER WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. ALWAYS perform this procedure in the presence of an assistant. The position of the footrest, ...
Part No. 1052712 Rev D 47 Terminator SS INSTALLING/ADJUSTING OPTIONAL CLAMP ON RAISED FOOTREST (FIGURE 2) INSTALLING 1. Install the two (2) half clamps onto either side of the wheelchair frame approximately 2-inches above existing footrest with two (2) allen screws provided. 2. Repeat for the opposite side of the wheelchair. 3. Slide the clamp o ...
Terminator SS 48 Part No. 1052712 Rev D SECTION 6 FOOTREST/ANTI-TIPPER FOOTREST / ANTI-TIPPER FIGURE 3 - INSTALLING/ADJUSTING OPTIONAL A4 FOOTREST Allen Screws Footrest Tube Flat Screws Footplate Flat Screws DEPTH HEIGHT ANGLE FOOTPLATE DEPTH ADJUSTMENT 1. Loosen, but do not remove the four (4) flat screws and locknuts that secure footplate to t ...
Part No. 1052712 Rev D 49 Terminator SS FIGURE 4 - ANTI-TIPPER REPLACEMENT/ADJUSTMENT 1-1/2 to 2-inch clearance Anti-tipper Release Buttons Anti-tipper Bar Anti-tipper Socket Camber Clamp Hole ANTI-TIPPER REPLACEMENT/ADJUSTMENT (FIGURE 4) WARNING Anti-tippers MUST BE attached at all times. Inasmuch as the ANTI-TIPPERS are an option on this wheel ...
Terminator SS 50 Part No. 1052712 Rev D SUSPENSION SECTION 7 SUSPENSION WARNING After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result. ELASTOMERS AND SUSPENSION CAUTION Weather conditions may affect elastomers. Invacare recommends that elastomers be ...
Part No. 1052712 Rev D 51 Terminator SS FIGURE 1 - REPLACING REAR ELASTOMERS LOWER Elastomer Recessed Spacer Telescoping Tube Mounting Bolt Locknut Nylon Washer Nylon Washer Suspension Arm UPPER Elastomer 4. Install the locknut onto the mounting bolt. NOTE: It may be necessary to compress the rear suspension system to install the locknut onto th ...
Terminator SS 52 Part No. 1052712 Rev D Elastomer Fork Bolt Fork Stem SUSPENSION SECTION 7 NOTE: Caster not shown for clarity. DETAIL B DETAIL C REPLACING FRONT ELASTOMERS (FIGURE 2) WARNING Ensure the detent ball protrudes past the fork BEFORE use. Otherwise, injury or damage may occur. 1. Remove the bolt and locknut securing the fo ...
Part No. 1052712 Rev D 53 Terminator SS Receiver Tube Receiver Tube Clamp Suspension Tube Marks FIGURE 3 - REMOVING/INSTALLING SUSPENSION TUBES Axle Tube Camber Clamp Suspension Tube Hex Bolts Locknuts Camber Insert DETAIL "B" - SUSPENSION TUBE HARDWARE REMOVING/INSTALLING/REPLACING SUSPENSION TUBES (FIGURE 3) NOTE: Invacare recommends ...
Terminator SS 54 Part No. 1052712 Rev D SECTION 7 SUSPENSION 4. Close the receiver tube clamps. Refer to OPENING/CLOSING CLAMPS in SECTION 5 of the manual. 5. Reinstall the rear wheels. Refer to REMOVING/INSTALLING REAR WHEELS in SECTION 5 of this manual. 6. Adjust suspension to correspond to the user's weight. Refer to REPLACING REAR ELAST ...
Part No. 1052712 Rev D 55 Terminator SS SECTION 7 SUSPENSION 3. If necessary, refer to REPLACING/ADJUSTING CASTERS in PROCEDURE 5 of the manual to replace the casters or adjust the caster position. 4. After replacing or adjusting the caster size/position, refer to ADJUSTING FRONT CASTER HEIGHT in PROCEDURE 5 of the manual to add/remove fork spac ...
Terminator SS 56 Part No. 1052712 Rev D PROCEDURE 7 SUSPENSION SUSPENSION 13. Install the rear wheels into the camber inserts. Refer to REMOVING/INSTALLING REAR WHEELS in PROCEDURE 5 of this manual. 14. Adjust the axle tube. Refer to ADJUSTING THE AXLE TUBE in PROCEDURE 5 of this manual. NOTE: The performance of the wheelchair will be affected i ...
Part No. 1052712 Rev D 57 Terminator SS REPOSITIONING QUICK RELEASE LEVERS (FIGURE 6) NOTE: This procedure should only be performed if quick release levers are on top of the axle mounting tube and interfere with the desired rear seat-to-floor adjustment. This procedure will position the quick release lever on the bottom of the axle tube. 1. Remo ...
Terminator SS 58 Part No. 1052712 Rev D NOTES NOTES NOTES ...
Part No. 1052712 Rev D 59 Terminator SS LIMITED WARRANTY PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975. This warranty is extended only to the original purchaser/user of our products. This warranty gives you specific legal rights and you may also have other legal ...
Invacare Corporation www.invacare.com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Invacare and Top End are registered Elyria, Ohio USA Mississauga Ontario trademarks of Invacare Corporation. 44036-2125 L4Z 4G4 Canada Yes, you can. , A4 and Terminator are 800-333-6900 800-668-5324 tr ade mar ks o f Invacare Corporation. Dual Grip is a reg ...
Invacare TerminatorTM SSのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TerminatorTM SSの取扱説明書
- Invacareの製品カード
- パンフレット
- またはInvacare TerminatorTM SSの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Invacare TerminatorTM SSの取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、Invacare TerminatorTM SSの取り付け説明書、サービスマニュアル、簡易説明書、またはInvacare TerminatorTM SSのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Invacare TerminatorTM SSの製品を使用するにあたって最も人気のある説明書を閲覧できます。
Invacare TerminatorTM SSデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがInvacare TerminatorTM SSを使用するのを助ける技術的文書のことです。説明書は通常、全てのInvacare TerminatorTM SSユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
Invacareの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. Invacare TerminatorTM SSの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははInvacare TerminatorTM SSの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Invacare TerminatorTM SSに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Invacare TerminatorTM SSデバイスの基本機能を使うにあたってのヒント。 Invacare TerminatorTM SSのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Invacare TerminatorTM SSに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるInvacare TerminatorTM SSのメーカー/サービスへの連絡先に関する情報。
Invacare TerminatorTM SSについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもInvacare TerminatorTM SSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがInvacare TerminatorTM SSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。