Alloy Computer Products RNS5の取扱説明書

22ページ 0.73 mb
ダウンロード

ページに移動 of 22

Summary
  • Alloy Computer Products RNS5 - page 1

    Alloy RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch User’s Manual Rev.1.1 20-Jan-2005 ...

  • Alloy Computer Products RNS5 - page 2

    Content Introduction ......................................................... 1 Features ................................................................... 1 Package Checklist .................................................... 2 Hardware Description ......................................... 3 Dimensions ......................................... ...

  • Alloy Computer Products RNS5 - page 3

    Introduction Industrial environments are usually more demanding than office environments. Harsh temperature conditions, vibration, dust, etc. all put higher demands on the quality and reliability of your networking equipment. To survive harsh industrial environments, Alloy provides you with the RNS5/8 Series Industr ial 5-port/8-port 10/100Mbps Eth ...

  • Alloy Computer Products RNS5 - page 4

    Package Checklist Alloy RNS5/8 Industrial 5-port/8-port Et hernet Rail Switches are packaged with the following items:  RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch  One DIN-Rail clip (attached to the RNS5/8)  One wall mounting plate and six screws  User’s manual CD-ROM RNS5/8 Switch User’s Manual CD-ROM W a l l M o u n t i ...

  • Alloy Computer Products RNS5 - page 5

    Hardware Description D i m e n s i o n s RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch dimensions (W x H x D) are 54mm x 135mm x 105mm F r o n t P a n e l The Front Panel of the RNS 5 Industrial 5-port Ethernet Rail Switch is shown in Figure A. LED Indicators UTP Ports Figure A. Front Panel of the RNS5 In dustrial 5-port Ethernet Rail Switch ...

  • Alloy Computer Products RNS5 - page 6

    The Front Panel of the RNS 8 Industrial 8-port Ethernet Rail Switch is shown in Figure A. LED Indicators UTP Ports Figure A. Front Panel of the RNS8 In dustrial 8-port Ethernet Rail Switch 4 ...

  • Alloy Computer Products RNS5 - page 7

    Bottom View The bottom view of the RNS5/8 Industr ial 5-port/8-port Et hernet Rail Switch consists of one terminal block connector with two DC power inputs, Alarm output and one DC IN power jack for an additional AC/DC power adapter. Figure B. Bottom view of the RNS5/8 Indu strial 5-port/8-port Ethernet Rail Switch Wiring the DC Power Inputs Follow ...

  • Alloy Computer Products RNS5 - page 8

    L E D I n d i c a t o r s There are 5 diagnostic LEDs and 8 Port LEDs located on the Front panel of the RNS5 Industrial Ethernet Rail Switch. These LED indicators provide administrators with real-time system stat us. Table 1 gives descriptions of the functions of each LED indicator. LED Status Description Green Power is on. PWR Off No power is bein ...

  • Alloy Computer Products RNS5 - page 9

    Port LED Status Description Orange The port is operating in full-duplex mode. Blinking orange Collision of Packets occurring. Off The port is in half-duplex mode or no device is attached. Green A network device is detected. Blinking green The port is transmitting or receiving packets from the TX device. Port Status (Port 1 to Port 4) Off No device ...

  • Alloy Computer Products RNS5 - page 10

    Blinks The port is transmitting or receiving packets from the TX device. Off No device is attached. Orange The port is operating in full-duplex mode. Blinks Collision of packets occurs. FDX/COL of Port 7/8 Off The port is in half-duplex mode or no device is attached. Port LED Status Description Orange The port is operating in full-duplex mode. Blin ...

  • Alloy Computer Products RNS5 - page 11

    Fig C Straight Through Cabling Schematic Fig C-1 Cross Over Cabling Schematic All ports of RNS5/8 support the auto-MD I/MDI-X function. When you use an Ethernet cable to connect other devices, such as computers, swit ches or hubs, pin 1, 2, 3, and 6 of the 8-pin RJ45 c onnector are used to communicate with the connected devices. Pin1, 2, 3, and 6? ...

  • Alloy Computer Products RNS5 - page 12

    Mounting Installation DIN-Rail Mounting The DIN-Rail clip is already attached to the RNS5/8 when packaged. If the DIN-Rail clip is not screwed on the RNS5/8, follow the instructions and the figure below to attach the DIN-Rail clip to the RNS5/8. Rear Panel of the RNS5/8 DIN-Rail Clip 1. Use the screws to attach the DIN-Rail clip to the rear panel o ...

  • Alloy Computer Products RNS5 - page 13

    Follow the steps below to mount t he RNS5/8 to the DIN-Rail track: 1. First, insert the upper end of the DIN-Rail clip into the back of the DIN-Rail track from its upper side. 2. Lightly push the bottom of the DIN-Rail clip into the track. 3. Check if the DIN-Rail clip is tightly attached on the track. 4. To remove the RNS5/8 from the track, revers ...

  • Alloy Computer Products RNS5 - page 14

    Wall Mounting Follow the steps below to install the RNS5/8 with the wall mounting plate. 1. To remove the DIN-Rail clip from the RNS5/8, loosen t he screws from the DIN-Rail clip. 2. Place the wall mounting plate on the rear panel of the RNS5/8. 3. Use the screws to tighten the wa ll mounting plate ont o the RNS5/8. 4. Use the hook holes at the cor ...

  • Alloy Computer Products RNS5 - page 15

    Hardware Installation The following figure illustrates a typi cal application of RNS5/8 Industrial 5-port/8-port Ethernet Rail Switch. Installation and Testing 1. Take your RNS5/8 Industrial 5-port/8- port Rail Switch out of the package box. 2. Check if the DIN-Rail clip is attached to the RNS5/8. If the DIN-Rail clip is not attached to the RNS5/8, ...

  • Alloy Computer Products RNS5 - page 16

    4. Pull the terminal bloc k off the RNS5/8 and wire the power lines . Refer to the Wiring the DC Power Inputs section for how to wire the power inputs. 5. PWR1 and PWR2 dual power inputs can be connected to power sources simultaneously. When the primary power s ource fails (the default setting is PWR1), the system wil l automatically switch to the ...

  • Alloy Computer Products RNS5 - page 17

    10. Power on the host, activate the Command Line mode, and ping the connected Ethernet device to see if it will respond. 10.1 To enable the “Command Line mode”, click on Run in the Start menu, type Command , and click on OK to continue. 10.2 Type ping 192.168.1.1 command to check the connection. Here we use IP address 192.168.1.1 as an example. ...

  • Alloy Computer Products RNS5 - page 18

    12. Power on the host, activate the Command Line mode, and ping the connected Ethernet device by typing “ping –t 192.168.1.1” command to see if it will respond. 13. The parameter ”t” allows you to cont inue to ping the network device, as shown in the figure below. Before you continue, make sure that both PWR1 and PWR2 are successfully con ...

  • Alloy Computer Products RNS5 - page 19

    Trouble shooting  Make sure you are using the correct VDC power supplies (12 to 48 VDC) or power adapters. Do not use power adapt ers with DC output over 48V. It will damage the device.  Select Ethernet cables with specifications suitable for your applications to set up your system. Ethernet cables are cat egorized into unshielded twisted-pai ...

  • Alloy Computer Products RNS5 - page 20

     Technical Specifications Standards IEEE 802.3 10BaseT Ethernet IEEE 802.3u 100BaseT(X) Fast Ethernet IEEE802.3x Flow Control and Back pressure Protocols CSMA/CD Technology Store and Forward Transmission Rate 14,880 pps for Ethernet port 148,800 pps for Fast Ethernet port MAC address table size RNS5: 1K MAC address table RNS8: 2K MAC address tab ...

  • Alloy Computer Products RNS5 - page 21

    Power Suppl y 12 to 48 VDC, redundant dual DC power inputs with reverse polarity protection, and a removable terminal block for master and slave VDC power inputs. Power consumption RNS5: 2.8 Watts RNS8: 4.6 Watts Packet throughput ability RNS5: 0.74Mpps @ 64bytes (5TX) RNS8: 1.19Mpps @ 64bytes (8TX) Installation DIN-Rail kit and wall mounting panel ...

  • Alloy Computer Products RNS5 - page 22

    IEC60068-2-6 (Vibration) 20 ...

メーカー Alloy Computer Products カテゴリー Switch

Alloy Computer Products RNS5のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- RNS5の取扱説明書
- Alloy Computer Productsの製品カード
- パンフレット
- またはAlloy Computer Products RNS5の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Alloy Computer Products RNS5の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Alloy Computer Products RNS5の取り付け説明書、サービスマニュアル、簡易説明書、またはAlloy Computer Products RNS5のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Alloy Computer Products RNS5の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Alloy Computer Products RNS5デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAlloy Computer Products RNS5を使用するのを助ける技術的文書のことです。説明書は通常、全てのAlloy Computer Products RNS5ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Alloy Computer Productsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Alloy Computer Products RNS5の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAlloy Computer Products RNS5の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Alloy Computer Products RNS5に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Alloy Computer Products RNS5デバイスの基本機能を使うにあたってのヒント。 Alloy Computer Products RNS5のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Alloy Computer Products RNS5に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAlloy Computer Products RNS5のメーカー/サービスへの連絡先に関する情報。

Alloy Computer Products RNS5についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAlloy Computer Products RNS5の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAlloy Computer Products RNS5で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)