Haier HSU-09HV03/R2(SDB)の取扱説明書

27ページ 0.99 mb
ダウンロード

ページに移動 of 27

Summary
  • Haier HSU-09HV03/R2(SDB) - page 1

    No. SPLIT TYPE ROOM AIR CONDITIONER OPERA TION MANUAL Please read this operation manual before using the air conditioner HSU-07HV03/R2(DB) HSU-09HV03/R2(DB) HSU-12HV03/R2(DB) HSU-09HV03/R2(SDB) HSU-12HV03/R2(SDB) HSU-18HV03/R2(DB) ...

  • Haier HSU-09HV03/R2(SDB) - page 2

    Bef ore disposing an old air conditioner that goes out of use, please mak e sure it's inop- erativ e and saf e. Unplug the air conditioner in order to av oid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require speciali- zed w aste disposal. The v aluab le materials contained in an a ...

  • Haier HSU-09HV03/R2(SDB) - page 3

    Do not obstruct or cov er the ventilation grille of the air conditoner.Do not put fingers or any other things into the inlet/outlet and s wing louver. Do not allow children to pla y with the air conditioner.In no case should children be allow ed to sit on the outdoor unit. The refr igerating circuit is leak-proof . 1.Applicable ambient temper ature ...

  • Haier HSU-09HV03/R2(SDB) - page 4

    Cautions STRICT ENFORCEMENT Safety Instruction Installation W ARNING Please read the f ollowing Safety Instructions carefully prior to use. The instructions are classified into two le vels , WARNING and CA UTION according to the seriousness of possible risks and damages as follo ws. Compliance to the instructions are str ictly required f or saf ety ...

  • Haier HSU-09HV03/R2(SDB) - page 5

    Cautions W ARNING When abnormality such as burnt-small found, immediately stop the operation button and contact sales shop. OFF Use an exclusive power source with a circuit breaker ENFORCEMENT Connect power supply cord to the outlet completely Use the proper voltage Do not use power supply cord in a bundle. Take care not to damage the power supply ...

  • Haier HSU-09HV03/R2(SDB) - page 6

    P ar ts and Functions Indoor unit Outdoor unit 5 CHANGE-FOR-FRESH-AIR BOX OUTLET CONNECTING PIPING AND ELECTRICAL WIRING INLET 1 2 3 4 CHANGE-FOR-FRESH-AIR TUBE CHANGE FOR FRESH AIR SIGNAL WIRE DRAIN HOSE 5 6 7 UV light degerming device (inside) (Only for the units of SDB) Displa y board Inlet Air Purifying Filter V er tical flap (adjust up and dow ...

  • Haier HSU-09HV03/R2(SDB) - page 7

    P ar ts and Functions Used to select CODE A or B with a press,A or B will be display ed on LCD . Please select A without special explanation. 1.CODE When the remote controller appears abnormal, use a sharp pointed ar ticle to press this button to reset the remote controller normal. 2.RESET Used to select TIMER ON, TIMER OFF , TIMER ON-OFF . 4. TIME ...

  • Haier HSU-09HV03/R2(SDB) - page 8

    P ar ts and Functions Used to select CODE A or B with a press,A or B will be display ed on LCD . Please select A without special explanation. 1.CODE When the remote controller appears abnormal, use a sharp pointed ar ticle to press this button to reset the remote controller normal. 2.RESET Used to select TIMER ON, TIMER OFF , TIMER ON-OFF . 4. TIME ...

  • Haier HSU-09HV03/R2(SDB) - page 9

    Remov e the batter ies in case unit won't be in usage f or a long per iod. If there are any displa y after taking-out, just need to press reset ke y. P ar ts and Functions Clock Set When unit is star ted for the first time and after replacing batteries in remote controller, clock should be adjusted as f ollows: Remote controller's operati ...

  • Haier HSU-09HV03/R2(SDB) - page 10

    Note: (1)when the unit is operating health or sterilize function," " displayed on the display board and " " is displayed on the display board in the sterilize function. Operation Remote controller 9 STERILIZE 2.Health anion function Air conditioner starts health anion function operation. For twice press, disappears,the operation ...

  • Haier HSU-09HV03/R2(SDB) - page 11

    A uto Operation Operation Remote controller 10 STERILIZE About A uto Operation Under the mode of auto operation, air conditioner will automatically select Cool or Heat operation according to room temperature. 5.Unit stop Press ON/OFF button, the unit stops . 1. Unit star t Press ON/OFF on the remote controller, unit star ts. 2.Select operation mode ...

  • Haier HSU-09HV03/R2(SDB) - page 12

    Cool Operation Remote controller 2.Select operation mode Press FAN button. For each press, fan speed changes as follows: Press MODE button. For each press, operation mode changes as follows: Remote controller: Remote controller: Then Select COOL operation Press TEMP. button Every time the button is pressed, temp.setting increase 1 o C,if kept depre ...

  • Haier HSU-09HV03/R2(SDB) - page 13

    2.Select operation mode Press F AN button. For each press , fan speed changes as f ollows: Press MODE button. For each press , operation mode changes as f ollows: Remote controller : Remote controller : Then Select DR Y operation Press TEMP . button Every time the button is pressed, temp .setting increase 1 o C ,if kept depressed, it will increase ...

  • Haier HSU-09HV03/R2(SDB) - page 14

    F an Operation 2.Select operation mode Press F AN button. For each press , fan speed changes as f ollows: Press MODE button. For each press , operation mode changes as f ollows: Remote controller : Remote controller : Then Select F AN operation 3.Fan speed selection 4.Unit stop About F AN operation In F AN operation mode, the unit will not oper ate ...

  • Haier HSU-09HV03/R2(SDB) - page 15

    Operation 2.Select operation mode Press F AN button. For each press , fan speed changes as f ollows: Press MODE button. For each press , operation mode changes as f ollows: Remote controller : Remote controller : Then Select HEA T operation Press TEMP . button Every time the button is pressed, temp .setting increase 1 o C ,if kept depressed, it wil ...

  • Haier HSU-09HV03/R2(SDB) - page 16

    2.Up and down air flo w direction V er tical flap P os.1 P os.1 P os.2 P os.3 P os.4 P os.6 P os.5 P os.4 P os.3 P os.2 P os.1 P os.6 P os.1 P os.2 P os.3 P os.4 P os.5 P os.6 P os.2 P os.3 P os.4 P os.5 P os.6 (Auto swing) F or each press of button, air flow direction on remote controller displa ys as f ollows according to different oper ation mod ...

  • Haier HSU-09HV03/R2(SDB) - page 17

    If the wind speed is high or middle before setting for the sleep, set for lowing the wind speed after sleeping. If it is low wind, no change. 5.Set the wind speed change when sleeping Bef ore going to bed, you can simply press the SLEEP button and unit will oper ate in SLEEP mode and bring you a sound sleep . Use of SLEEP function After the unit st ...

  • Haier HSU-09HV03/R2(SDB) - page 18

    Remote Controller T imer On/Off Operation Operation Hints: After replacing batteries or a power failure happens, time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if time setting is the same as previous one. 17 Set clock correctly before starting TIME ...

  • Haier HSU-09HV03/R2(SDB) - page 19

    Remote Controller T imer On-Off Operation Operation Just press TIMER button several times until TIMER de disappears. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved. Set clock correctly before starting TIMER operation. 1. After unit starts, select your desired operation mode Operation ...

  • Haier HSU-09HV03/R2(SDB) - page 20

    1.Press ON/OFF to starting Operation The liquid cr ystal will displa y the working state of last time (Except timer, sleeping, pow er/soft and health airflow). Setting the comf or t work conditions. 2.The setting of health airflow function 1).Press the button of health airflow, appears on the display. The nether inlet and outlet grills of the air c ...

  • Haier HSU-09HV03/R2(SDB) - page 21

    When the remote controller is manipulated, it gets the system back to the nor mal operation mode . Emer g ency and T est Operation Operation Emer gency operation: Use this operation only when the remote controller is def ective or lost. When the emergency operation s witch is pressed,the" Pi "sound is heard once, which means the star t of ...

  • Haier HSU-09HV03/R2(SDB) - page 22

    For Smar t Use of The Air Conditioner Setting of proper room temperature Close doors and windo ws dur ing operation If the unit is not to be used f or a long time, turn off the po wer supply main s witch. Use the timer eff ectiv ely Use the louv ers eff ectiv ely Do not b lock the air inlet or outlet Maintenance Proper temperature During cooling op ...

  • Haier HSU-09HV03/R2(SDB) - page 23

    For Smar t Use of The Air Conditioner W ARNING Air Filter cleaning Open the inlet grille by pulling it upw ard. Remov e the filter. Clean the filter. Attach the filter. Close the inlet grille. Push up the filter's center tab slightly until it is released from the stopper, and remov e the filter downward. Use a vacuum cleaner to remov e dust, o ...

  • Haier HSU-09HV03/R2(SDB) - page 24

    The green aspect of the bacteria-killing medium air purifying filter will face outside, the white aspect will face to the machine. 23 1.For the units with UV light degerming function ,the air purifying filter of the bacteria-killing medium and the multi-lights touching intermediary is effective for a long time and don't need to be changed (UV ...

  • Haier HSU-09HV03/R2(SDB) - page 25

    T o K eep Y our Air conditioner in Good Condition after Season. Operate in cooling mode f or 2-3 hours. Put off the po wer supply cord. T ake out the batteries from the wireless remote controller. Cleaning the body . To pre v ent breeding mold or bad smell, be sure to operate at the designated temperature or 30 O C ,cooling mode and High speed f an ...

  • Haier HSU-09HV03/R2(SDB) - page 26

    Bef ore Setting in High season Cleaning the standard air filter. Connecting the ear thing cable . Do not b loc k the air inlet or outlet. Plug-in Caution Caution After brush awa y dust at the plug, inser t the plug of the pow er supply cord into the outlet completely .In case of suing exclusiv e circuit breaker,s witch on the circuit breaker. NO WE ...

  • Haier HSU-09HV03/R2(SDB) - page 27

    Is the air filter dir ty? Nor mally it should be cleaned e very 15 days . Are there any obstacles bef ore inlet and outlet? Is temperature set correctly? Are there some doors or windows left open? Is there any direct sunlight through the window during the cooling operation?(Use cur tain) Are there too much heat sources or too many people in the roo ...

メーカー Haier カテゴリー Air Conditioner

Haier HSU-09HV03/R2(SDB)のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HSU-09HV03/R2(SDB)の取扱説明書
- Haierの製品カード
- パンフレット
- またはHaier HSU-09HV03/R2(SDB)の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Haier HSU-09HV03/R2(SDB)の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Haier HSU-09HV03/R2(SDB)の取り付け説明書、サービスマニュアル、簡易説明書、またはHaier HSU-09HV03/R2(SDB)のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Haier HSU-09HV03/R2(SDB)の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Haier HSU-09HV03/R2(SDB)デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHaier HSU-09HV03/R2(SDB)を使用するのを助ける技術的文書のことです。説明書は通常、全てのHaier HSU-09HV03/R2(SDB)ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Haierの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Haier HSU-09HV03/R2(SDB)の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHaier HSU-09HV03/R2(SDB)の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Haier HSU-09HV03/R2(SDB)に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Haier HSU-09HV03/R2(SDB)デバイスの基本機能を使うにあたってのヒント。 Haier HSU-09HV03/R2(SDB)のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Haier HSU-09HV03/R2(SDB)に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHaier HSU-09HV03/R2(SDB)のメーカー/サービスへの連絡先に関する情報。

Haier HSU-09HV03/R2(SDB)についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHaier HSU-09HV03/R2(SDB)の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHaier HSU-09HV03/R2(SDB)で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)