日本語 dropdown-ico

Windsor CDT7IA/10080050の取扱説明書

23ページ 0.82 mb
ダウンロード

ページに移動 of 23

Summary
  • Windsor CDT7IA/10080050 - page 1

    Read instructions before operating the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen MOD EL: COUNTRY CDT7IA/10080050 AUSTRALIA CDT7IB/10080060 BRITIAN CDT7IE/10080070 EUROPE CDT7IS/10080080 SWITZERLAND Operating Instructions (USA) Bedienungsanleitung (GER) 86038340 04/19/07 PRV NO. 98707 AF CARPET EXTRACTOR IP ...

  • Windsor CDT7IA/10080050 - page 2

    MACHINE DATA LOG/OVERVIEW CADET 86038340 04/19/07 2ENG For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ __________________________ __________________________ __________________________ Address: __________________ __________________________ __________________________ _________________________ ...

  • Windsor CDT7IA/10080050 - page 3

    TABLE OF CONTENTS CADET 86038340 04/19/07 3ENG Machine Data Log/Overview (English). ........ 1 Machine Data Log/Overview (German). ....... 2 Table of Contents (English) .......................... 3 Table of Contents (German) ......................... 4 HOW TO USE THIS MANUAL How to use this Manual. ........................1-1ENG SAFETY Important Sa ...

  • Windsor CDT7IA/10080050 - page 4

    HOW TO USE THIS MANUAL CADET 86038340 04/19/07 1-1ENG This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ordered from authori zed Windsor dealers. Wh ...

  • Windsor CDT7IA/10080050 - page 5

    CADET 86038340 04/19/07 2-1ENG IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric shock, or injury: Connect to a properly grounded outlet . See Gr ...

  • Windsor CDT7IA/10080050 - page 6

    HAZARD INTENSITY LEVEL CADET 86038340 04/19/07 2-2ENG The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY. The level of hazard intensity is determined by the following definitions: ...

  • Windsor CDT7IA/10080050 - page 7

    SAFETY LABEL LOCATION CADET 86038340 04/19/07 2-3ENG NOTE: These drawings indicate the location of safet y labels on the CDT7//1008023 0. If, at any time, the labels become illegible contact your Windso r r epresentative for prom pt re placement. WARNING DECAL 86242230 PRV NO. 500009 ...

  • Windsor CDT7IA/10080050 - page 8

    ACCESSORY TOOL USAGE CADET 86038340 04/19/07 3-10ENG Turn on Pump and Vacuum Switch. Note: Be sure intermittent/continuous switch is in center (off) position and brush is in storage position. Squeeze handle on accessory tool to begin cleaning. STEP 3 STEP 4 STEP 1 STEP 2 Use only one of the following acceptable accessory tools. 86000000 – PRV NO. ...

  • Windsor CDT7IA/10080050 - page 9

    TECHNICAL SPECIFICATIONS CADET 86038340 04/19/07 3-1ENG POWER TYPE ELECTRICAL: 230-240 V, 7 A, 50 HZ ELECTRIC VACUUM MOTOR: (1) –3 stage, 1 hp, 99 cfm (2.80 cubic meters/min.) Waterlift –117” (297cm) BRUSH: (1) 15” (38.1 cm.) SOLUTION PUMP: 100 PSI, diaphragm style, internal bypass SOLUTION CAPACITY: 7 gallons (26.5ltr) RECOVERY CAPACIT Y: ...

  • Windsor CDT7IA/10080050 - page 10

    CONTROLS/COMPONENT LOCATIONS CADET 86038340 04/19/07 3-2ENG 1. Main Han dle. Used to pull and maneuver machine. 2. Electrical Cord. 3. Pump Switch. Turns on pump and enables spray. 4. Brush/Spray switch. Turns on brush motor and activates electro-valve to dispense solution to floor through jets. Intermittent, off, and continuous settings. 5. Vacuum ...

  • Windsor CDT7IA/10080050 - page 11

    CONTROLS/COMPONENT LOCATIONS CADET 86038340 04/19/07 3-3ENG 1 2 3 10 9 1. Solution Accessory Tool Hookup. Used for various auxiliary cleaning tools. 2. Vacuum Hose Door. Used to connect various auxiliary 1-1/2 inch cleaning tool vacuum hoses. 3. Brush Height Adjustment. Used to regulate brush height from storage position to various carpet heights. ...

  • Windsor CDT7IA/10080050 - page 12

    CONTROLS/COMPONENT LOCATIONS CADET 86038340 04/19/07 3-4ENG 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout. 6. Lift Handle. 2 1 3 4 5 6 6 ...

  • Windsor CDT7IA/10080050 - page 13

    FILLING OPERATIONS CADET 86038340 04/19/07 3-5ENG FILLING THE CADET NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank . Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before replacing recovery tank . CHEMICALS Suitable ...

  • Windsor CDT7IA/10080050 - page 14

    OPERATIONS CADET 86038340 04/19/07 3-6ENG Remove electrical cord and literature from recovery tank. Fill solution tank (see filling operations, page 3-5). Adjust brush to proper setting. Note: For good operation the brush must skim the carpet. If circuit breaker trips raise brush to prevent damage to motor or carpet. Plug cord into grounded outlet. ...

  • Windsor CDT7IA/10080050 - page 15

    OPERATIONS CADET 86038340 04/19/07 3-7ENG Select intermittent or continuous switch setting to turn on brush and start solution spray. The intermittent setting requires the operator to hold t he switch in the “on” position with the thumb, and is typically used in small areas where short cleaning passes are made. The continuous setting allows the ...

  • Windsor CDT7IA/10080050 - page 16

    CLEANING PROCEDURE CADET 86038340 04/19/07 3-8ENG 1ft. (30cm) Release intermittent setting or turn off continuous setting on brush/spray switch approximately 1 foot before ending cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area a minimum of 1 inch on the right (clo ...

  • Windsor CDT7IA/10080050 - page 17

    CLEANING PROCEDURE CADET 86038340 04/19/07 3-9ENG To speed drying, use a Windblower ™ fan. Empty recovery tank by releasing dump hose. Use a hose with cold water to clean out the recovery tank. Also drain solution tank after each use. STEP 7 STEP 8 After cleaning, turn off all controls, return brush to storage position and carefully unplug machin ...

  • Windsor CDT7IA/10080050 - page 18

    MAINTENANCE CADET 86038340 04/19/07 4-1ENG PERIODIC MAINTENANCE Twice a month, flush a white vinegar solution (One quart vinegar to two gallons of water) or anti-browning solution (mixed as directed) through the extractor. This will prevent build-up of alkaline residue in the system. If spray jets become clogged, remove the spray tips, wash them th ...

  • Windsor CDT7IA/10080050 - page 19

    MAINTENANCE CADET 86038340 04/19/07 4-2ENG ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. ...

  • Windsor CDT7IA/10080050 - page 20

    MAINTENANCE CADET 86038340 04/19/07 4-3ENG ! WARNING: BELT REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank and brush. 3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the frame. 4. Loosen the (4) screws that hold the brush motor in place and slide motor ...

  • Windsor CDT7IA/10080050 - page 21

    TROUBLESHOOTING CHART CADET 86038340 04/19/07 4-4ENG PROBLEM CAUSE SOLUTION No Power, Nothing Runs 1. Is the cord plugged in. 2. Circuit breaker tripped in buildi ng. 3. Faulty switch. 4. Faulty power cord or pigtail. 1. Plug in cord. 2. Reset breaker 3. Call for service. 4. Call for service. Vacuum Motor Will Not Run 1. Vacuum circuit breaker trip ...

  • Windsor CDT7IA/10080050 - page 22

    WIRING DIAGRAM CADET 86038340 04/19/07 4-5ENG 86268750 PRV NO. 88567 86268750 PRV NO. 88567 86268750 PRV NO. 88567 86268750 PRV NO. 88567 86268350 PRV NO. 88270 86003650 PRV NO. 34362 86001240 PRV NO. 14020 86268900 PRV NO. 88655 86268900 PRV NO. 88655 86004480 PRV NO. 41353 ...

  • Windsor CDT7IA/10080050 - page 23

    NOTES CADET 86038340 04/19/07 4-6ENG ...

メーカー Windsor カテゴリー Carpet Cleaner

Windsor CDT7IA/10080050のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CDT7IA/10080050の取扱説明書
- Windsorの製品カード
- パンフレット
- またはWindsor CDT7IA/10080050の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Windsor CDT7IA/10080050の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Windsor CDT7IA/10080050の取り付け説明書、サービスマニュアル、簡易説明書、またはWindsor CDT7IA/10080050のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Windsor CDT7IA/10080050の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Windsor CDT7IA/10080050デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWindsor CDT7IA/10080050を使用するのを助ける技術的文書のことです。説明書は通常、全てのWindsor CDT7IA/10080050ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Windsorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Windsor CDT7IA/10080050の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWindsor CDT7IA/10080050の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Windsor CDT7IA/10080050に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Windsor CDT7IA/10080050デバイスの基本機能を使うにあたってのヒント。 Windsor CDT7IA/10080050のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Windsor CDT7IA/10080050に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWindsor CDT7IA/10080050のメーカー/サービスへの連絡先に関する情報。

Windsor CDT7IA/10080050についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもWindsor CDT7IA/10080050の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWindsor CDT7IA/10080050で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)