Humminbird ID 600の取扱説明書

28ページ 0.37 mb
ダウンロード

ページに移動 of 28

Summary
  • Humminbird ID 600 - page 1

    ...

  • Humminbird ID 600 - page 2

    INSTALLATION PREPARATION PARTS SUPPLIED PARTS SUPPLIED Before installing your new Humminbird fish f inder, please ensure the following parts are included in the box: • Fishfinder • Transducer with 20’ (6m) of cable and mounting hardware kit • Mounting system an d mounting hardware kit • 6’ (2m) power cable • Publications kit It any of ...

  • Humminbird ID 600 - page 3

    INSTALLATION PREPARATION INSTALLATION OVERVIEW Determining How to Mount the Transducer Your Humminb ird fishfinder includes a standard transducer. This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat. The transom installation, which is the most widely used, places the transducer on the outside ...

  • Humminbird ID 600 - page 4

    INSTALLATION PREPARATION ALTERNATE M OUNTING METHODS ALTERNATE TRANSDUCERS AND MOUNTING METHODS Your Humminbird fishfinder comes with everything necessary for installation and operation on most boats. However, there are several situations which may require a different type of transducer. In board boats, wood or metal hulls, and sail boats create un ...

  • Humminbird ID 600 - page 5

    INSTALLATION PREPARATION TRANSDUCER EXCHANGE TRANSDUCER EXCHANGE Other transducers are available as replacements for the standard transducer. You may exchange your new and unassembled transducer for another type by returning i t to the address listed in Customer Support. Some transducers may have additional cost. Refer to the Accessory catalog or c ...

  • Humminbird ID 600 - page 6

    INSTALLAT ION TRANSOM INSTALLATION Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This chapter contains information critical to the correct installation of your transducer. Due to the wide variety of b oat hulls, only general instructions are presented in the installation guide. Each bo ...

  • Humminbird ID 600 - page 7

    INSTALLATION TRANSOM INSTALLATION • If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence, and a different mounting technique or transducer type should be considered. Step Two - Drill the Mounting Holes 1. Remove the mounting template from the front of the Operations Manual. 2. Hold the te ...

  • Humminbird ID 600 - page 8

    INSTALLATION TRANSOM INSTALLATION Step Four - Mount the Transducer to the Transom 1. Apply silicone sealant to the mounting holes drilled into the transom. 2. Align the transducer assembly with the drilled holes in the transom (Figure 8). 3. U se either a flat head screwdriver, a 5/16" (8mm) hex driver, or a 5/16" (8mm) socket to mount th ...

  • Humminbird ID 600 - page 9

    mounting bracket. Drill this hole and install the screw after final testing and adjustments have been completed. ...

  • Humminbird ID 600 - page 10

    INSTALLATION TRANSOM INSTALLATION Step Six - Route the Cable There are several ways to route the transducer c able to the to the area where the control head will be installed. The most common procedure routes the cable through the transom into the boat. Inside the boat there is often a channel or conduit used for other wiring that the cable can be ...

  • Humminbird ID 600 - page 11

    INSTALLATION INSIDE THE HULL INSTALLATION INSIDE THE HULL INSTALLATION Inside the hull installation requires the mount system and control head be installed and operational. See Installing the Control Head for instruction on installing the unit. Inside the hull mountin g generally produces good results in single thickness fiberglass - hulled boats. ...

  • Humminbird ID 600 - page 12

    The transducer cannot transmit through air. The water purges any air from between the transducer and the hull and fills any voids in the coarse fiberglass surface. ...

  • Humminbird ID 600 - page 13

    INSTALLATION INSIDE THE HULL INSTALLATION 3. Power up the Control Head. 4. Run the boat at various speeds and water depths while observing the screen on the Control Head. If the unit functions well at low speeds but b egins to skip or miss the bottom at higher speeds, the transducer needs to be moved. If depth performance is required, test the fish ...

  • Humminbird ID 600 - page 14

    INSTALLATION CONTROL HEAD INSTALLATION CONTROL HEAD INSTALLATION Step One - Determine Where to Mount Begin the installation by determining where to mount the control head. Consider the following to determine best location: • The cables for power, transducer and temp/speed accessories (if applicable) should be installed first and must reach the mo ...

  • Humminbird ID 600 - page 15

    fuse in the connection. If you must wire the control head directly to a battery, be sure to install an inline fuse holder ...

  • Humminbird ID 600 - page 16

    INSTALLATION CONTROL HEAD INSTALLATION and one amp fuse (not inc luded) for the protection of the unit (Figure 21). Humminbird is not responsible for over voltage or over current failures. In order to minimize the potential for interference with other marine electronics a separate power source (such as a second batter y) may be necessary. Step Thre ...

  • Humminbird ID 600 - page 17

    Optional: If the ca bles pass outside the mounting bracket, install the hole cover over the hole and fasten in place using the two #8 x 7/8” (22mm) wood screws (Figure 24). ...

  • Humminbird ID 600 - page 18

    INSTALLATION CONTROL HEAD INSTALLATION Step Five - Assembling the Connector Holder 1. Insert the cabl e connectors into the connector holder. The cable connectors are labeled, and there are corresponding labels on the connector holder (Figure 26). The slots for the connectors are keyed to prevent reverse installation, so do not force the connector ...

  • Humminbird ID 600 - page 19

    INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water, however you can initially confirm basic operation with the boat trailered. Press POWER once to turn the unit on. There will be an audible chirp when any button is pressed to confirm the button press. If the unit does not power - up, ensu ...

  • Humminbird ID 600 - page 20

    Installing the SeaScope ID600 Before mounting the SeaScope ID600, gather the parts you need; SeaScope ID600, gimball mounting bracket, mounting hardware kit, power cable, and transducer cable. If the transducer cable is not long enough for your installat ion, see “Accessories” earlier in the manual for information on the EC - 6 10’ extension ...

  • Humminbird ID 600 - page 21

    3. Remove the rear housing and store for f uture use. 4. Drill a 3 1/2 “ hole in the dash or console at the location you have chosen. This is a standard gauge opening size, and hole saws are available at hardware stores, tool rental stores, or marine dealers. 5. Place the SeaScope ID600 in the opening, and mark the four mounting holes from which ...

  • Humminbird ID 600 - page 22

    Section 4: Using the SeaScope ID600 This section provides complete information on operating the SeaScope ID600 through its fro nt panel controls. You are encouraged to read this information completely as you first learn to use the SeaScope ID600. Doing so will ensure you make the most if it many features and functions. The first part of this sectio ...

  • Humminbird ID 600 - page 23

    STOP: Press this to “freeze” the display so you can study it. Press it again to restart the display movement. SELECT: This button is used to access the following functions for further adjustments: • Sensitivity/Units • Bottom Al arm • Fish Alarm • Zoom • Bottom Lock • Display Speed • Depth Range • Fish ID To adjust any of these, ...

  • Humminbird ID 600 - page 24

    range. For example, if you set it at “+2”, Sensitivity remains 2 settings higher that the normal automatic setting. Pressing the ON - OFF button when the SENS menu is displa yed switches the unit of depth measurement between feet, fathoms and meters. Bottom Alarm 2. Using Bottom Alarm; Factory setting; OFF The Bottom Alarm lets you specify the ...

  • Humminbird ID 600 - page 25

    The Fish Alarm alerts you with a chirping sound whenever the SeaScope ID600 detects fish (or another object not attached to the bottom). To activate it, select FISH ALM and press the ON - OFF button. A fish symbol reminds you that the alarm is on. Zoom 4. Using Zoom; Factory setting; OFF Zoom provides an up - close view. To activate it, select Zoom ...

  • Humminbird ID 600 - page 26

    Bottom - Lock provides an up - close view like Z oom, except that in this case the zoomed view automatically moves up or down to stay on the bottom. To use this feature, select BTM LOCK and press ON - OFF. The range of the display is shown when the Bottom - Lock is on. This is an ideal feature for finding structure or locating fish near the bottom. ...

  • Humminbird ID 600 - page 27

    Depth Range 7. Setting Depth Range; Factory setting; On (Auto matic) When you turn the SeaScope ID600 on it finds the bottom, sets the ideal depth range, and automatically adjusts the depth range (to as much as 480 ft) as the depth changes. In this “Auto Depth Range”mode, the bottom is blacked - in for easy - to - unders tand readings. If you p ...

  • Humminbird ID 600 - page 28

    press the ON - OFF button while within the Fish ID menu. Pressing the ON - OFF button again reactivates the ID function. ...

メーカー Humminbird カテゴリー Fish Finder

Humminbird ID 600のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ID 600の取扱説明書
- Humminbirdの製品カード
- パンフレット
- またはHumminbird ID 600の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Humminbird ID 600の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Humminbird ID 600の取り付け説明書、サービスマニュアル、簡易説明書、またはHumminbird ID 600のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Humminbird ID 600の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Humminbird ID 600デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHumminbird ID 600を使用するのを助ける技術的文書のことです。説明書は通常、全てのHumminbird ID 600ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Humminbirdの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Humminbird ID 600の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHumminbird ID 600の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Humminbird ID 600に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Humminbird ID 600デバイスの基本機能を使うにあたってのヒント。 Humminbird ID 600のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Humminbird ID 600に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHumminbird ID 600のメーカー/サービスへの連絡先に関する情報。

Humminbird ID 600についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHumminbird ID 600の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHumminbird ID 600で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)