Vermont Casting A052041の取扱説明書

24ページ 1.75 mb
ダウンロード

ページに移動 of 24

Summary
  • Vermont Casting A052041 - page 1

    F O R Y O U R S A F E T Y I f y o u sm e l l g a s: 1 S h u t o g a s to th e a p p l i a n c e . 2 E x t i n g u i sh a n y o p e n  a m e . 3 O p e n l i d . 4 I f o d or c on t i n u e s, i m m e d i a te l y c a l l y o u r g a s su p p l i e r o r  r e d e p a r tm e n t . F O R Y O U R SA F E TY 1 D o n o t st o r e or u se g a so l ...

  • Vermont Casting A052041 - page 2

    T able of Contents Page Number Chapter One - INSTALLATION 4 Necessary Information 4 Choosing a Safe Location 4 Portable L.P. Gas Grills 5 - 7 Important Features of the Series 4000 LP Gas Grill 8 L.P. Gas Dealer Instructions 9 Chapter Two - ASSEMBL Y INSTRUCTIONS 10 Identifying Parts 11 Attach Pillar to Grill Bottom 12 - 13 Assemble Base to Pillar 1 ...

  • Vermont Casting A052041 - page 3

    The gas fuel used by this product is highly flammable and must be used in a responsible and cautious manner . It is your responsibility to assemble, operate, and maintain your gas barbecue grill properly . If these instructions are ignored, there is a possibility of a hazardous fire or explosion which could result in proper- ty damage, physical inj ...

  • Vermont Casting A052041 - page 4

    • The ventilation openings of the cylinder enclosure must be kept free and clear from other debris. 6. Do Not store a spare L.P. gas cylinder under or near this appliance. • Do not store an L.P. cylinder in a build- ing, garage or any other enclosed area. Instead, store the cylinder outdoors in a well ventilated area, away from people and out o ...

  • Vermont Casting A052041 - page 5

    2. The system has a thermal element that will shut off the flow of gas between 240° F and 300° F . 3. The system has a flow-limiting device which when activated, will limit the flow of gas to 10 cubic feet per hour . 4. The pressure regulator and hose assem- bly provided is factory set at an outlet pres- sure of 11 inches water column (.4 lb. per ...

  • Vermont Casting A052041 - page 6

    L.P. GAS CYLINDER SPECIFICATIONS Any L.P. gas-supply cylinder used with this grill must be approximately 12 inches diameter and 18 inches high. The maxi- mum fuel capacity must be 20 pounds of propane. Full-cylinder weight should be approximately 38 pounds (43.7 lbs. nominal water capacity). The L.P. cylinder must have a shut-off valve terminating ...

  • Vermont Casting A052041 - page 7

    8 Rear view of Series A052041 grill with the heat shield, gaskets, collar assembly. HEA T SHIELD, GASKETS AND COLLAR W ARNING! Do not remove the heat shield, gaskets, collar assembly from the grill bottom. Operating this grill without the heat shield, gaskets, collar assembly attached to the grill bottom would result in a hazardous situation which ...

  • Vermont Casting A052041 - page 8

    Filling a Type 1 Cylinder Valve Example A: shows a CGA-510 POL fitting. Example B: shows using a Type 1 POL fitting. When using a cylinder exchange, be sure the exchanged cylinder is a T ype 1 cylinder; a 510 POL cylinder will not fit a T ype 1 regulator . F ILLING AND P URGING T YPE 1 L.P. G AS C YLINDERS DANGER! Purging and filling of L.P. Gas cy ...

  • Vermont Casting A052041 - page 9

    Assembly Instructions Chapter 2 Getting Star ted 1. Please follow the steps in the order that they are presented. 2. Assemble the grill where you plan to use it. 3. Y ou may want to place an old towel or cloth at the assembly site to prevent nuts and bolts from becoming lost. 4. Have a friend help. An assistant can make the assembly easier by holdi ...

  • Vermont Casting A052041 - page 10

    A ssembly Instructions • Identify the G r ill Parts warming rack (1) cooking grid (1) ceramic briquettes ( 1 package ) rock grate (1) left side table (1) right side table (1) base (1) master hardware bag (1) consisting of: (1) "A" bag (1) "B" bag (1) "C" bag (1) "D" bag 11 handle (1) handle standoff (2) gri ...

  • Vermont Casting A052041 - page 11

    HINT: For the first portion of the assembly you will be assembling the grill bottom, pillar and base up- side-down. 1. Position the grill bottom casting upside down so that the heat collar assembly is upward. 2. W orking from the back (open) side of the pillar, set the pillar upside down onto the collar assembly . 3. Locate the holes in the pillar ...

  • Vermont Casting A052041 - page 12

    back hinge strut pillar bottom grill bottom back gas control valve ends fuel supply hose w/ regulator burner venturi tubes collar 13 ...

  • Vermont Casting A052041 - page 13

    1. Lock the pre-assembled casters on base by pushing down on the latch. 2. Set the base upside-down on onto the pillar bottom as shown on the adjacent page, aligning holes in base with holes in pillar . 3. Insert six bolts through the holes in the pillar and base. Thread the locking hex nuts onto bolts. T ighten with a wrench and a flat- head screw ...

  • Vermont Casting A052041 - page 14

    15 ignitor unit base back top pillar black lead wires heat shield bottom casting back ...

  • Vermont Casting A052041 - page 15

    1 Now with the help of an assistant carefully turn the grill assembly right-side-up. 2. IMPORTANT : Inspect beneath the grill bottom to check that the control-valve ends are still inside the burner venturi tubes. The valve ends must always be inside the burner tubes for the grill to safely operate. grill bottom as shown from below back. No tools ne ...

  • Vermont Casting A052041 - page 16

    17 A TTENTION PRODUCT ASSEMBLER: Install the X-brace retainer wire across the back of the pillar for warranty validation. 3. Position the wire ends “A” and “B” firmly into the pillar corners behind the bolt heads and against the base. (See Lower Detail.) 4. Complete the installation by snapping bent ends “C” and “D” into the two hol ...

  • Vermont Casting A052041 - page 17

    Locate these parts: 18 tools needed: 3/8" open-end wrench 7/16" open-end wrench A ssembly Instructions • Install the Side T ables. 1/4-20 x 3/4” bolt ( 8 ) Use hardware bag “C”: 1/4-20 hex nut ( 8 ) right side table assembly ( 1 ) 1. Insert four 3 /4" bolts through holes in the support brackets of the right side table assembl ...

  • Vermont Casting A052041 - page 18

    19 3. Insert four 3 /4" bolts through holes in the support brackets of the left side table assembly . 4. Attach the left side table to the four holes located in the left side of the grill bottom using the locking hex nuts provided. HINT: Preformed hooks included on the right side table assembly may be used to keep cooking utensils (not include ...

  • Vermont Casting A052041 - page 19

    20 A ssembly Instructions • Assemble the G rill Lid tools needed: 7/16" open-end wrench flat-blade screwdriver handle standoff ( 2 ) handle ( 1 ) 1. Position the back of the lid so that the rear holes are in line with the hinge struts on the back of the grill bottom. 2. Gently set the grill lid onto the grill bottom. hairpin ( 2 ) use hardwa ...

  • Vermont Casting A052041 - page 20

    7. Raise the lid to attach the front handle. 8. Attach a handle standoff to the front of the grill lid, as shown. 9. Insert one end of the handle into the hole of the standoff. 10.Place other standoff onto handle and while holding the handle in place assem- ble the opposite standoff to the lid in the same manner . 3. Hold the lid to align the hinge ...

  • Vermont Casting A052041 - page 21

    rock grate ( 1 ) No tools are needed. A ssembly Instructions • Installing the In ternal G rill Parts . 22 ceramic briquettes ( 1 box ) warming rack ( 1 ) 1. Place the single rock grate into the grill bottom. cooking grid ( 1 ) 2. Open the package containing the ceramic briquettes and place them on the rockgrate. Locate these parts: ...

  • Vermont Casting A052041 - page 22

    3. It is important to properly arrange all the ceramic briquettes onto the rock grate to allow for good air flow during use. NOTICE THE SPACING: The proper amount of briquettes are supplied and there is no need to add more. Some space between the briquettes is necessary. 4. Set the porcelain coated cooking grid on the front and back ledges formed i ...

  • Vermont Casting A052041 - page 23

    Replacement parts are available direct from our warehouse. Some components are not available preassembled and may be ordered separately. For convenience, the following parts list is provided along with a representation of the items listed. Charges for replacement parts and shipping may apply . For warranty replacements, proof of own- ership and dat ...

  • Vermont Casting A052041 - page 24

    35 Base Assembly Breakdown of P r eassembled Components Pillar Assembly Bottom/Burner Assembly Side T able Assemblies 1 Base Assembly consisting of: 1 Base SF AH000402 2 Locking Caster AH000303 2 Caster AH000305 quantity description part number 1 Bottom/Burner Assembly consisting of: 1 Cast Iron Burner AZ001505 1 V enturi T ube w/gasket AZ000507 8 ...

メーカー Vermont Casting カテゴリー Gas Grill

Vermont Casting A052041のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- A052041の取扱説明書
- Vermont Castingの製品カード
- パンフレット
- またはVermont Casting A052041の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Vermont Casting A052041の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Vermont Casting A052041の取り付け説明書、サービスマニュアル、簡易説明書、またはVermont Casting A052041のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Vermont Casting A052041の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Vermont Casting A052041デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがVermont Casting A052041を使用するのを助ける技術的文書のことです。説明書は通常、全てのVermont Casting A052041ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Vermont Castingの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Vermont Casting A052041の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははVermont Casting A052041の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Vermont Casting A052041に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Vermont Casting A052041デバイスの基本機能を使うにあたってのヒント。 Vermont Casting A052041のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Vermont Casting A052041に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるVermont Casting A052041のメーカー/サービスへの連絡先に関する情報。

Vermont Casting A052041についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもVermont Casting A052041の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがVermont Casting A052041で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)