Sony SDX-700Cの取扱説明書

32ページ 0.41 mb
ダウンロード

ページに移動 of 32

Summary
  • Sony SDX-700C - page 1

    AIT Drive 2-676-745- 31 (1)  2006 Sony Corporation AIT-3 Ex TAPE DRIVE SDX-800V Series User’s Guide ...

  • Sony SDX-700C - page 2

    2 This document contains proprietary information which is protected by copyright. All rights reserved. No part of this document may be photocopied, reproduced or translated to another language without prior written consent of Sony. The information contained in this document is subject to change without notice. SONY MAKES NO WARRANTY OF ANY KIND WIT ...

  • Sony SDX-700C - page 3

    3 IMPORTANT SAFEGUARDS For your protection, please read these safety instructions completely before operating the appliance, and keep this manual for future reference. Carefully observe all warnings, precautions and instructions on the appliance, or described in the operating instructions and adhere to them. USE Power Sources – This unit should b ...

  • Sony SDX-700C - page 4

    4 INSTALLATION Water and Moisture – Do not use power-line operated units near water – for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Power-Cord Protection – Route the power cord so that it is not likely to be walked on or pinched by items placed upon or against it, paying ...

  • Sony SDX-700C - page 5

    5 Table of Contents Overview .................................................................................................................. 6 Introduction .............................................................................................................. 7 About AIT Drives ............................................................. ...

  • Sony SDX-700C - page 6

    6 Overview The Sony SDX-800V series drives are high capacity data storage devices using Advanced Intelligent tape (AIT) technology. The SDX-800V series drives achieve high data reliability through Read-After-Write, an additional level of Error Correction Code, and other features. The Sony SDX-800V series drives store data on tape using standard for ...

  • Sony SDX-700C - page 7

    7 Introduction About AIT Drives SDX-800V series drives are internal AIT drive units that use data cartridges conforming to the AIT-3 Ex format. SDX-800V series drives support AIT-1, AIT-2, AIT-3 and AIT-3 Ex formats. Features The SDX-800V series drives have the following features: • Support reading and writing to data cartridges conforming to the ...

  • Sony SDX-700C - page 8

    8 Precautions Useable Cartridges SDX-800V series can be used with data cartridges marked with the AIT-1 * , AIT-2 * , AIT-3 or AIT-3 Ex logo. * Read only Notes • Be sure to use only data cartridges designed specifically for AIT (do not use 8 mm video cartridges) as this may damage the drives. • Do not use anything but AIT cartridges with this s ...

  • Sony SDX-700C - page 9

    9 Transportation • Keep the original packing materials to facilitate safe transportation of the drives. • Always remove the tape/media cartridge before moving the drives. After removing the drives from the computer, repack them into their original packing. SCSI Termination The SDX-800V series drives conform to the Microsoft PC97 standard, which ...

  • Sony SDX-700C - page 10

    10 Installation SCSI Connection/Setting the SCSI ID SCSI 68pin Connector 5 V Power Connector 1 2 3 4 GND GND 12 V Disable Enable Parity Note : = = = CLOSED/Jumper Don’ t care OPEN/Jumper not installed Pa rity Disable No Connection SCSI ID 3 SCSI ID 2 SCSI ID 1 SCSI ID 0 Jumpers SCSI ID SCSI ID 0 1 2 3 4 5 6 7 8 9 10 1 1 12 13 14 15 2 1 0 P .D. N. ...

  • Sony SDX-700C - page 11

    11 Option Switches (DIP Switch) DIP Switch Positions Default ON OFF 12345678 DIP Switch 1 DR (Disaster Recovery) Mode (OFF) 2 Emulation Mode (OFF) 3 AIT Library Interface Mode (ON) 4 Reserved (OFF) 5 Terminator Power (ON) 6 Periodic Cleaning Req (ON) 7 DC Control (1) (ON) 8 DC Control (2) (OFF) ...

  • Sony SDX-700C - page 12

    12 DR (Disaster Recovery * ) Mode To enable DR Mode, set position 1 [Drive Mode] switch to ON. ON OFF 12345678 * In Disaster Recovery Mode, an SDX-800V series drive enters the DR Standby Mode 15 seconds after you insert a write-protected tape into the drive, and all the drive LED blink. If you restart the drive while the LED are blinking, it starts ...

  • Sony SDX-700C - page 13

    13 Library Mode The Library Mode can be enabled with a DIP switch. ON OFF 12345678 When switch 3 is ON, AIT-1, 2, 3 compatible Library Mode is enabled. With this switch OFF, ACI Mode is enabled. Terminator Power Control DIP switch This DIP switch determines whether terminator power is supplied to the SCSI bus. To enable terminator power, set positi ...

  • Sony SDX-700C - page 14

    14 Mounting Holes For 3.5" Standard Height 155.0 0.5mm [6.10" 0.02"] 90.0 0.3mm [3.54" 0.01"] 60.0 0.3mm [2.36" 0.01"] 70.0 0.3mm [2.76" 0.01"] 31.0 0.3mm [1.22" 0.01"] 21.0 0.3mm [0.83" 0.01"] 41.2 0.5mm [1.62" 0.02"] 4.8 0.5mm [0.19" 0.02"] 6-M3 (depth 2.5mm [0.1 ...

  • Sony SDX-700C - page 15

    15 Reconfiguring from 5.25" Model to 3.5" Model You can reconfigure the 5.25" model to the 3.5" model yourself. 1 Remove the 2 screws for each side rail. 2 Take the side rail off. Side Rail (L) Side Rail (R) ...

  • Sony SDX-700C - page 16

    16 Orientation 10 10 10 10 10 10 10 10 ...

  • Sony SDX-700C - page 17

    17 Attaching and Removing the Dust Cover Attaching the Dust Cover 1 Align the dust cover’s hinge clips (one on each side) with the pins of the drive bezel. • The dust cover should be positioned so that the magnets * on the cover’s back face the drive bezel. * This magnet does not affect the tape of the cartridge. • Holding the dust cover at ...

  • Sony SDX-700C - page 18

    18 2 Press down at an angle on each side in turn until you hear the hinge clips click into place. Caution Do not press the dust cover in horizontally from the front. Doing so could cause the dust cover to break. 3 Close the dust cover. This completes attachment of the dust cover. ...

  • Sony SDX-700C - page 19

    19 Removing the Dust Cover 1 Open the dust cover. 2 Holding the dust cover at both corners, carefully raise the dust cover. The dust cover hinge clips and drive bezel pins uncouple. Note We recommend that you use the drive with the dust cover. ...

  • Sony SDX-700C - page 20

    20 Operation Location of 3 LEDs There are three LED indicatiors (TAPE MOTION LED, CLEANING REQUEST LED, REPLACE TAPE LED) and an EJECT button on the front panel of the SDX-800V series drives. Front Panel TAP E MOTION CLEANING REQUEST REPLACE TAP E Advanced Intelligent T ape LED EJECT button LED Indication for Drive Status The LED indicators are def ...

  • Sony SDX-700C - page 21

    21 Drive Operation Loading a Cartridge Note While setting the data cartridge, do not turn off the host computer. This may cause a malfunction or damage data. 1 Turn on the host computer. Check that the drive’s TAPE MOTION LED, CLEANING REQUEST LED and REPLACE TAPE LED go off. 2 Open the dust cover. 3 Set the AIT data cartridge orientation as show ...

  • Sony SDX-700C - page 22

    22 Unloading a Cartridge The cartridge can be removed from SDX-800V series drives in response to a SCSI Unload command, or by pressing the EJECT button. When the EJECT button is pressed, the tape is rewound and the cartridge ejected from the slot. Write-protecting a Cartridge Cartridges can be write-protected by sliding the tab on the back of the c ...

  • Sony SDX-700C - page 23

    23 How to Clean 1 Load the cleaning cartridge (SDX3X-CL) into the SDX-800V. Cleaning starts automatically. 2 Cleaning takes from a few seconds to a minute for the SDX- 800V, *1 and the cartridge is automatically ejected when finished. *1 The cleaning time varies depending on the condition of the drive. Caution Do not rewind the cleaning cartridge a ...

  • Sony SDX-700C - page 24

    24 Reel motor Loading motor Emergency Tape Removal Procedure 1 Remove the drive from the chassis or enclosure to allow access to the bottom of the drive. 2 Remove the drive’s top cover. 3 Locate the small opening in the bottom of the drive and insert the tip of a precision screwdriver so that the Loading motor shaft can be rotated. 4 Rotate the m ...

  • Sony SDX-700C - page 25

    25 Caution Stop rotating the motor shaft immediately, when the guide B gets to the area below the line C-C (This line is defined by 2 circular tape guide surfaces of the cartridge). Otherwise, the gears of the drive can be damaged. The Initial Position of the Threading Mechanism 5 Before the manual ejection procedure, tape slack must be removed in ...

  • Sony SDX-700C - page 26

    26 Interface Implementation Supported SCSI Messages Abort Identify Target Reset Ignore Wide Residue Command Complete Message Parity Error Disconnect Message Reject Extended Message No Operation – Synchronous Data Transfer Request – Wide Data Transfer Request – Parallel Protocol Request Supported SCSI Commands Erase Inquiry Load/Unload Locate ...

  • Sony SDX-700C - page 27

    27 Specifications Product Specifications Altitude Operating 0 to 3048 m (0 to 10,000 ft.) Vibration Operating Swept Sine 5 to 500 Hz *0.25 G Peak 1 Octave/min. 3 axes, 3 directions Non-operating Swept Sine 5 to 500 Hz *0.5 G Peak 1 Octave/min. 3 axes, 3 directions Acoustic Noise (A) curve weight Streaming Write/Read 35 dB (A) Insert/Eject 60 dB (A) ...

  • Sony SDX-700C - page 28

    28 Temperature and Humidity Range Temperature Operating 5˚C to 40˚C ( ∆ T<10˚C/h) (41˚F to 104˚F ( ∆ T<18˚F/h)) Non-operating (mech.) – 40˚C to 70˚C ( ∆ T<20˚C/h) (– 40˚F to 158˚F ( ∆ T<36˚F/h)) Non-operating (tape) – 40˚C to 45˚C ( ∆ T<20˚C/h) (– 40˚F to 113˚F ( ∆ T<36˚F/h)) Humidity Operatin ...

  • Sony SDX-700C - page 29

    29 Sony Contacts For further information, please contact the appropriate Sony location listed below: Sony Electronics Inc., Tape Storage Solutions (USA) URL: http://www.storagebysony.com Sony of Canada Ltd., AV/IT Marketing Group Computer Peripherals Product Marketing 115 Gordon Baker Road Toronto, Ontario, M2H 3R6 Canada TEL: (416) 499-1414 or (1) ...

  • Sony SDX-700C - page 30

    30 Sony Brasil Ltda. Rua Inocéncio Tobias, 125, Barra Funda São Paulo-SP, Brasil 01144-000 TEL: (55) 11-2196-9000 FAX: (55) 11-2196-9186 URL: http://www.sonybrasil.com.br Sony Australia Limited 33-39 Talavera Rd. NORTH RYDE, NSW 2113 TEL: 1300-13-7669 FAX: 02-9870-5864 e-mail: CIC-customerissues@ap.sony.com Sony New Zealand Akoranga Business Park ...

  • Sony SDX-700C - page 31

    ...

  • Sony SDX-700C - page 32

    Printed in U.S.A. ...

メーカー Sony カテゴリー Computer Drive

Sony SDX-700Cのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SDX-700Cの取扱説明書
- Sonyの製品カード
- パンフレット
- またはSony SDX-700Cの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Sony SDX-700Cの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Sony SDX-700Cの取り付け説明書、サービスマニュアル、簡易説明書、またはSony SDX-700Cのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Sony SDX-700Cの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Sony SDX-700Cデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSony SDX-700Cを使用するのを助ける技術的文書のことです。説明書は通常、全てのSony SDX-700Cユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Sonyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Sony SDX-700Cの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSony SDX-700Cの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Sony SDX-700Cに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Sony SDX-700Cデバイスの基本機能を使うにあたってのヒント。 Sony SDX-700Cのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Sony SDX-700Cに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSony SDX-700Cのメーカー/サービスへの連絡先に関する情報。

Sony SDX-700Cについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSony SDX-700Cの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSony SDX-700Cで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)