CDA HN6410の取扱説明書

24ページ 関係なし
ダウンロード

ページに移動 of 24

Summary
  • CDA HN6410 - page 1

    IMPORT ANT : PLEASE REFER TO P A GE 20 FOR INFORMATION ON CONFIGURING THE POWER CONSUMPTION MODE CORRECTL Y . THE HOB MUST BE CONFIGURED A T FIRST SWIT CH ON. Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu hn6410 Induction ...

  • CDA HN6410 - page 2

    2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment. This appliance is no ...

  • CDA HN6410 - page 3

    3 2004/108/EC. Parts intended to come into contact with food conform to 89/109/EC. IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling servi ...

  • CDA HN6410 - page 4

    4 • Do not place hot lids flat on the hob top. A “ suction” eect could cause damage to the hob. • Do not drag cookware across the hob top: in the long term, this could cause damage to the hob. • Do not store cleaning or flammable products in the unit below the hob. • Always use appropriate cookware. • Do not cook unopened tins of ...

  • CDA HN6410 - page 5

    5 Important • Do not use the hob if the glass surface is cracked or damaged to prevent the risk of electric shock. Disconnect it from the power supply . • Ensure that the power cables of connected electrical appliances near the hob are not in contact with the cooking zones. Important: Please refer to page 20 for information on conguring the ...

  • CDA HN6410 - page 6

    6 Cooking on Induction The principle of induction cooking is based on magnetic eect. When you put your cookware on an induction zone and switch it on, the electronic boards in the hob produce induced currents in the base of the cookware and instantly raise its temperature. This heat is then transferred to the food inside the cookware. The best c ...

  • CDA HN6410 - page 7

    7 Using Y our Hob The table below oers guidance as to what each power level is for . Power level Type of cooking 0 Switched o 1/2 Melting (butter/chocolate) or keeping food warm 2/3 K eeping food hot or to heat small quantities of liquid 3/4 Heat larger quantities of liquid (sauces etc.) 4/5 Slow boiling, e.g spaghetti, soups, stews, potatoes ...

  • CDA HN6410 - page 8

    8 Using Y our Hob T o switch the hob on T o switch the power on, touch and hold the key for appro ximately two seconds. The hob will beep and all four zone displays will show zero. Please note: If a power level is not set within ten seconds, the hob will switch o automatically . T o set the power level There are power keys for each individual zo ...

  • CDA HN6410 - page 9

    9 Booster The hob is equipped with a booster function, allowing a higher power level than the maximum for appro ximately ten minutes. T o turn on the booster function, touch the “+” key when the power level is already set at 9 . “ P” will show in the display . T o cancel the booster at any time, touch the “-” key to return to power leve ...

  • CDA HN6410 - page 10

    10 seconds remaining. At the end of the timer , the selected zone will switch o and the timer display and the zone timer LED will flash. The hob will beep for appro ximately one minute. T o switch o the beep and the flashing displays, touch any key . T o cancel the timer T ouch the timer “+” and “-” keys together . Please note: Canc ...

  • CDA HN6410 - page 11

    11 childlock is switched o . Use of the childlock when the hob is o The childlock LED is illuminated to show the childlock is on. Use of the childlock when the hob is in use The childlock LED is illuminated to confirm that the childlock is switched on and no adjustments can be made to any of the zones or the timer . It is possible to switch ...

  • CDA HN6410 - page 12

    12 Small object safety Anything left on the control panel (e.g. cutlery or towels) will cause the hob to switch o automatically and there will be a beep every ten seconds until the obstruction is removed. T emperature limiter The hob is equipped with a temperature limiting sensor that will switch o the zone and show “ C” alternating with ...

  • CDA HN6410 - page 13

    13 Ecient Use of Y our Hob The hob is equipped with zones of dierent sizes, designed to accommodate most shapes and sizes of pan. For best results, only use pans with flat bottoms and choose an appropriate zone depending on the size of the pan. The most ecient use of the hob is shown below , where the pan and zone are correctly chosen. Us ...

  • CDA HN6410 - page 14

    14 Care and Maintenance Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. Important: • S team cleaners must not be used when cleaning this appliance. • Y ou should use a non-abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif ) will scratch the surface and could erase th ...

  • CDA HN6410 - page 15

    15 In the event of a fault with the hob, please advise CD A Customer Care of any fault code shown on the display Contact CD A Customer Care A : Customer Care Department, The CD A Group L td, Harby Road, Langar , Nottinghamshire , NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www . cda.eu T roubleshooting On rst use Y ou obs ...

  • CDA HN6410 - page 16

    16 IMPORT ANT - PLEASE NOTE: In the event of any breakage , crack or cracking – even minimal – of the vitroceramic glass, immediately disconnect your appliance to prevent a risk of electric shock and contact CD A Customer Care. In use Y ou observe that Possible Causes What should you do ? The hob has stopped operating. The hob beeps at appro xi ...

  • CDA HN6410 - page 17

    17 Fitting the Hob Unpacking the hob: T ake care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 180mm away from any adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 100mm if the adjacent surface is resistant to ...

  • CDA HN6410 - page 18

    18 recommended) (Fig. 4). If the instructions supplied with the hood dictate that the hood must be installed at a height greater than 600mm, then that height is the minimum required. W all furniture requirements: The minimum height of any cabinet immediately above the hob is 900mm. The minimum height of any adjacent units (including light pelmets) ...

  • CDA HN6410 - page 19

    19 How to Install the Hob Overall dimensions of the hob: Width: 580 mm Depth: 510 mm W orktop cut-out dimensions: Width: 560 mm Depth: 490 mm 1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood to ensure that you will have the required clearance. The cut-out (Fig. 5) shows a 60m ...

  • CDA HN6410 - page 20

    20 P ower Conguration This hob can be connected to a 13, 16, 25 or 32Amp supply and configured to work on any of these power settings. If the hob is connected to a 32Amp supply all four zones can be used on the maximum setting with boost at the same time. If , however , the hob is connected and configured to a 13Amp supply and all four zones a ...

  • CDA HN6410 - page 21

    21 Mains Electricity Connection W arning! this appliance must be earthed W e recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E. T . and local regulations. This hob is intended to be connected to permanent, fixing wiring and dependent on the power configurati ...

  • CDA HN6410 - page 22

    22 3.5k W-7 .2kW modes When configured in any mode other the 2.8k W , the hob should be installed into a dedicated cooker outlet and protected by the size of fuse shown in the table above. This appliance is intended to be connected to fix ed wiring by a double pole switch, having a contact separation of at least 3mm in all poles. The switch must ...

  • CDA HN6410 - page 23

    23 ...

  • CDA HN6410 - page 24

    Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu ...

メーカー CDA カテゴリー Stove

CDA HN6410のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HN6410の取扱説明書
- CDAの製品カード
- パンフレット
- またはCDA HN6410の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、CDA HN6410の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、CDA HN6410の取り付け説明書、サービスマニュアル、簡易説明書、またはCDA HN6410のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、CDA HN6410の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

CDA HN6410デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCDA HN6410を使用するのを助ける技術的文書のことです。説明書は通常、全てのCDA HN6410ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

CDAの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. CDA HN6410の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCDA HN6410の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。CDA HN6410に関してこのドキュメントで見つけることができる全てのヒントの目次
3. CDA HN6410デバイスの基本機能を使うにあたってのヒント。 CDA HN6410のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。CDA HN6410に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCDA HN6410のメーカー/サービスへの連絡先に関する情報。

CDA HN6410についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCDA HN6410の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCDA HN6410で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)