Miele DA 337 Iの取扱説明書

44ページ 1.27 mb
ダウンロード

ページに移動 of 44

Summary
  • Miele DA 337 I - page 1

    Operating Instructions for the DA 337 i Ventilation System To prevent accidents and machine damage, ö] read these Operating Instructions before installation or use. M.-Nr. 05 473 690 ...

  • Miele DA 337 I - page 2

    Contents Caring for the en vironment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Warning and Safety Inst ructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the app liance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 De ...

  • Miele DA 337 I - page 3

    Caring for the env ironmen t Disposal of packing material The transport and protective packing are environmentally friendly for dispo- sal and can normally be recycled. Please recycle. Disposal of an old appli ance Old appliances contain materials that can be recycled. Please contact your local recycling center about the possi- bility of recycling ...

  • Miele DA 337 I - page 4

    Warning and Safety Instructions Read these Operating Instructions car efully before install ing or using the Ventil ation System. This appliance is intended for residential use only. Use the ap- pliance only for its intended pur- pose. The manufacturer cannot be held responsible for damages caused by improper use of the hood. Read all the instructi ...

  • Miele DA 337 I - page 5

    WARNING To reduce the risk of fire, use only metal ductwork. Any fittings, sealant, or materials used to install the ductwork must be made of approved non-flammable materials. Never connect an exhaust hood to an active chimney, dryer vent, vent flue, or room ventilating ductwork. Seek professional advice before connecting an exhaust hood vent to an ...

  • Miele DA 337 I - page 6

    WARNING TO REDU CE THE RISK OF I NJURY TO P ERS ON S IN THE EVENT OF A RANGE T OP GREASE FIRE, OBSERVE THE FOLLLOWI NG: Sm other flam es with a close fit- ting lid, cookie sheet, or metal tray, then turn off the burner. Be careful to prevent burns. If the flames do not go out immediately, evacuate and call the fire dep artment. Never pick up a flam ...

  • Miele DA 337 I - page 7

    When connecting the hood to an ex- ternal vent, make sure that there is adequate ventilation in the room where the exhaust hood is to be used. When using the hood in the same area as other appliances requiring room air (e.g. non-electric water heaters, gas cooktops, gas ovens, etc.) make cer - tain that the air extracted by the hood does not hinder ...

  • Miele DA 337 I - page 8

    Guide to the appliance Guide to the appliance 8 ...

  • Miele DA 337 I - page 9

    b Vent connection c Active c harcoal filter slot d Control panel e Pull-out deflector plate f Interna l greas e fil ter g Over head cooktop l ight h Externa l gre ase fil ter i Light button j On/Off button k – / + Power level buttons (Four fan speed selection) l Delayed Shut Down button This control activates the Delayed Shut Down feature. The fa ...

  • Miele DA 337 I - page 10

    Description of the functions The hood works . . . by air extraction: The air is drawn in, cleaned by an exter- nal filter and then passed through an in- ternal filter before being directed out- side. The hood has a non-r eturn flap , (see "Installation"). This flap is closed when the hood is off. No exchange of room air and out- side air ...

  • Miele DA 337 I - page 11

    Operation Turning on the exhaust fan Pull the deflector plate out about 2 ” (5 cm) . The hood will then begin to operate at power lev el ” II ” . Selecting the power level Depending on how much the air needs to be filtered, there are four power le- vels available. For normal cooking a low to medium level is usually s uffi- cient. For frying o ...

  • Miele DA 337 I - page 12

    Turning off the exhaust fan Use the On/Off button to turn the fan off or Push the deflector plate back in. The next time the deflector plate is pulled out the hood will operate at power level ” II ” . Turning t he lights on or off The overhead lighting for the cooktop can be turned on or off independently of the fan. Pull the deflector plate ou ...

  • Miele DA 337 I - page 13

    Grease filter timer The timer for the grease filters is preset for 30 hours of use. After 30 hours the grease filter indicator will light. The grease filters must be cleaned at this time, and reset as follows: Hold the grease filter button for 4 seconds. The indicator light will go out. Active Charcoal Filter timer The filter timer for the Active C ...

  • Miele DA 337 I - page 14

    Changing the filter timer You can set the filter timer to suit the type of cooking you do. – Select a short time if you gr ill or fry frequently. – Select a longer time if you do not grill or fry often. – if you only cook occasionally, pro- gram a shorter time so the filters will be cleaned more often. Otherwise accumulated grease will harden ...

  • Miele DA 337 I - page 15

    Active charcoal filter The active charcoal filter is needed for recirculation mode. It is not used for vented extraction. The hood is preset for vented extrac- tion, the filter hour counter for the ac- tive charcoal filter is set to ” unlimited ” . For recirculation mode the filter timer needs to be set to the required time: Use the On/Off butt ...

  • Miele DA 337 I - page 16

    Cleaning and care Before servicing or cleaning the hood, disconnect it from the power supply by either removing the fuse, unplugging it, or manually ” tripping ” the circuit breaker. Ensure current is not supplied to the appliance while maintenance or re- pair work is performed. Housing Lacquered surfaces can be cleaned using a solution of hot ...

  • Miele DA 337 I - page 17

    External filter To remove the external filter pull the deflector plate out slightly. Turn the fan off. Holding the external filter at the front tilt it approximately 1 ” (3 cm ) down - wards and then pull it towards you to remove it. Internal filter Pull the deflector plate out to its full extension. The internal filter will now be visible. Holdi ...

  • Miele DA 337 I - page 18

    Return the filters Internal filter: Insert the filter into the hood so that it hooks into position at the back, then push it upwards at the front and make sure it engages in position on the left and right hand sides. Twist the grease filter catch as shown. Unfold the grease filter and lock the catch. External filter: Open the filter out. Make sure ...

  • Miele DA 337 I - page 19

    Inserting / replacing the active char coal f ilter For recirculation mode an active char- coal filter must be used in addition to the grease filters. It is designed to ab- sorb cooking odors. The active charcoal filter is inserted into a slot on the front of the appliance housing. Replacement active charcoal filters can be ordered from the Miele Te ...

  • Miele DA 337 I - page 20

    Changing the li ght bulb Before changing the light bulbs, dis- connect the hood from the power supply by either removing the fuse, unplugging it, or manually ” tripping ” the circuit breaker. Make sure that power is not re- stored to the appliance while main- tenance or repair work is performed. When in use the halogen bulbs become extremely ho ...

  • Miele DA 337 I - page 21

    After Sales Ser vice In the event of a problem which you can not fix yourself, please contact: – Your Miele dealer or – The Miele Technical Service Depart- ment, (see address on back cover ). When contacting the Technical Service Department, please quote the model and serial number of your appliance, both of which are shown on the data plate, v ...

  • Miele DA 337 I - page 22

    Appliance dimensions Appliance dimensions 22 ...

  • Miele DA 337 I - page 23

    Safety regulations prohibit the instal- lation of this hood over a solid fuel stove. The minimum safety distance be- tween the top of the cooktop and the bottom of the hood should be at least: – 18 ” (450 mm) above electric cooktop – 26 ” (650 mm) above gas cooktops – 26 ” (650 mm) above a Miele open grill A distance of 26 ” (650 mm) ...

  • Miele DA 337 I - page 24

    Cabinet back panel A minimum building in depth "A" of 275 mm is required to the back panel B or back wall. More building in space can be created in the cabinet by removing its back panel. The plastic trim C is designed to con- ceal gaps of 10 to 70 mm between the rear of the appliance and the wall. If the cabinet does not have a back pane ...

  • Miele DA 337 I - page 25

    25 ...

  • Miele DA 337 I - page 26

    Installation Installa tion acce ssories Installation 26 ...

  • Miele DA 337 I - page 27

    b 1 hose clip for securing the vent ducting to the vent connection. c 1 re ducing coll ar for exhaust ducting of a 5 ” (125 mm). d 1 no n-retu rn fl ap for fitting into the vent connection. e 2 runners (1 x right, 1x left) to support the ap - pliance in the cabinet. f 2 spacer blocks for installing the appliance in a 27 9 / 16 ” (70 cm) wide ca ...

  • Miele DA 337 I - page 28

    Installation procedure 1. Non-return flap (if needed) 2. Reducing collar (if needed) 3. Fit the runners in the cabinet 4. Hang and align the cabinet door 5. Position the appliance in the cabinet 6. Align the height of the appliance 7. Align the depth of the appliance 8. Fit the side spacers, the spacer strip, and the light cover 9. Set up for air e ...

  • Miele DA 337 I - page 29

    2. Reducing collar Air extraction The appliance is designed for vent ducting 6 ” (150 mm) diameter. If a 5 ” (125 mm) diameter is required: Place the reducing collar supplied on the vent socket and turn it to se- cure it in position (see ” Connection for air extraction ” ). Recirculation mode Place the reducing collar for a 5 ” (125 mm) d ...

  • Miele DA 337 I - page 30

    Fit the runners (Standard cabinet: 23 5 / 8 ” (60 cm) wide, 16 mm thick cabinet wall sides) Hold the runner against the cabinet so that the lower edge of the runner is flush with the cabinet. The first row of screws must be aligned with the pencil marks. The ” 16 mm" marking should face up- wards. Secure each runner with four 4,0 x 16 mm s ...

  • Miele DA 337 I - page 31

    5. Posi tion the appliance in the ca binet Lift the venting hood into the cabinet, making sure that the supports on the venting hood are sitting on the run- ners in the cabinet. Push it into the cabinet as far as it will go. The supports will slide under the anti- tip device b . Insert the adjusting scre ws c on the runners through the holes in the ...

  • Miele DA 337 I - page 32

    7. Align the depth of the appliance To move the appliance further out of the cabinet: Loosen screws c and tighten scre ws f . Tighten screws c again to secur e it into position. To move the appliance further into the cabinet: Loosen screws f and tighten scre ws c . Tighten screws f again to secur e it in position. Check the alignment again by pull- ...

  • Miele DA 337 I - page 33

    8 b. Space r strip for the re ar of the appliance Measure the gap ” T ” to be covered between the rear of the appliance and the wall. Use a knife to trim the spacer strip supplied to measurement ” T ” . Stick the spacer strip to the under- side of the appliance. Turn the side cover caps upwards and press into position. 9 a. S et up for v en ...

  • Miele DA 337 I - page 34

    9 b. Set up for recirculati on mode connection If the hood can not be installed for air extraction the appliance must be con- nected for recirculation. The following parts, available through your Miele Dealer or from the Miele Technical Service Department are necessary for using the appliance in re- circulation mode: – Recirculation conversion ki ...

  • Miele DA 337 I - page 35

    Specia l instal lation instructions Installation in t o a cabinet with 19 mm thick walls The runners have to be adapted as shown above. Screw the runners to the cabinet with the "19 mm" marking facing upwards as shown above. Installing in a 27 9 / 16 ” (70 cm) wide cabinet: The runners are secured to the spacer blocks. Screw the spacer ...

  • Miele DA 337 I - page 36

    When installed in a 27 ” (70 cm) wide cabinet the runners are fitted with the cover caps suplied. When installed in a 27 9 / 16 ” (70 cm) wide cabinet, the runners are fitted with the cover caps supplied. Cut the inserts to the required depth and fit into the sides of the cover caps. On units with 19 mm thick walls the cover caps for the runner ...

  • Miele DA 337 I - page 37

    Air extraction Danger of toxic fumes. Gas co oking ap plianc es rel ease carbo n monoxide tha t can be ha rm- ful or fa tal if inh aled. The exhaus t gases ext racte d by the hood shoul d be ve nted outsi de of the building only. Do not terminate the exhaust ducts in attics, garages, crawlspaces, etc. Please read and follow the "Warning and Sa ...

  • Miele DA 337 I - page 38

    Never connect an exhaust hood to an active chimney, dryer vent, vent flue, or room venting ductwork. Seek professional advice before connecting an exhaust hood vent to an existing, inactive chimney or vent flue. Ductwork with a diameter of less than 6" (150 mm) should only be used when absolutely necessary. As duct diameter decreases, the hood ...

  • Miele DA 337 I - page 39

    Electrical connection Electrical connection All electrical work should only be per - formed by a qualified electrician in ac- cordance with national and local safety regulations. The hood comes equipped with a 5 ft (1,5 m) power cord for connection to a 120 VAC, 15 A, 60 Hz power out- let. Verify that the information on the data plate matches the h ...

  • Miele DA 337 I - page 40

    Technical data Maximum load . . . . . . . . . . . . . 450 W Lighting . . . . . . . . . . . . . . . . 2 x 50 W Voltage . . . . . . . . . . . . . . . . . 120 VAC Frequency . . . . . . . . . . . . . . . ~ 60 Hz Circuit breaker . . . . . . . . . . . . . . . 15 A Fan Values derived using 6 ” (150 mm) duct- ing and EN 61591 test procedures Level I . . ...

  • Miele DA 337 I - page 41

    ...

  • Miele DA 337 I - page 42

    ...

  • Miele DA 337 I - page 43

    ...

  • Miele DA 337 I - page 44

    Alteration rights reserved / 44 / 000 US/CDN - 2600 This paper consists of cellulose bleached without the use of chlorine ...

メーカー Miele カテゴリー Ventilation Hood

Miele DA 337 Iのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DA 337 Iの取扱説明書
- Mieleの製品カード
- パンフレット
- またはMiele DA 337 Iの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Miele DA 337 Iの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Miele DA 337 Iの取り付け説明書、サービスマニュアル、簡易説明書、またはMiele DA 337 Iのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Miele DA 337 Iの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Miele DA 337 Iデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMiele DA 337 Iを使用するのを助ける技術的文書のことです。説明書は通常、全てのMiele DA 337 Iユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Mieleの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Miele DA 337 Iの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMiele DA 337 Iの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Miele DA 337 Iに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Miele DA 337 Iデバイスの基本機能を使うにあたってのヒント。 Miele DA 337 Iのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Miele DA 337 Iに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMiele DA 337 Iのメーカー/サービスへの連絡先に関する情報。

Miele DA 337 Iについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMiele DA 337 Iの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMiele DA 337 Iで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)