-
Harbor Freight Tools 36572 - page 1
1/4” AIR DIE GRINDER 36572 ASSEMBL Y AND OPERA TING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 9301 1 Visit our W eb site at: http://www.harborfreight.com T O PREVENT SERIOUS INJUR Y , READ AND UNDERST AND ALL W ARNINGS AND INSTRUCTIONS BEFORE USE. Copyright © 2004 by Harbor Freight T ools ® . All rights reserved. No portion of this ma ...
-
Harbor Freight Tools 36572 - page 2
PRODUCT SPECIFICA TIONS SA VE THIS MANUAL Y ou will need this manual for the safety warnings and precautions, assembly , operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover . Keep this manual and invoice in a safe a ...
-
Harbor Freight Tools 36572 - page 3
TOOL USE AND CARE 1. Use clamps or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand is unstable and may lead to loss of control. Only work on a workpiece that is properly secured. WORK AREA 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not o ...
-
Harbor Freight Tools 36572 - page 4
2. Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 3. Do not use the power tool if the T rigger does not turn it on or off. Any tool that cannot be controlled with the T rigger is dangerous and must be replaced. 4. Disconnect the air hose from ...
-
Harbor Freight Tools 36572 - page 5
SKU 36572 For technical questions, please call 1-800-444-3353 P AGE 5 3. Use clean, dry , regulated, compressed air at 90 PSI. Do not exceed the recommended 90 PSI. Never use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. 4. When connecting to the air supply: Prior to each use, if an automatic o ...
-
Harbor Freight Tools 36572 - page 6
SKU 36572 For technical questions, please call 1-800-444-3353 P AGE 6 2. Prior to use, the Die Grinder requires the attachment of a quick connector (not included) into its Air Inlet (1). T o do so, wrap approximately 3” of pipe thread sealer tape (not included) around the male threads of a quick connector . Then, rmlytightenthequi ...
-
Harbor Freight Tools 36572 - page 7
SKU 36572 For technical questions, please call 1-800-444-3353 P AGE 7 GRINDING DRUM (NOT INCLUDED) COLLET (28) SP ANNER (30) SP ANNER (30) COLLET NUT (29) SPINDLE (25) FIGURE B 5. Connect the air supply hose to the quick connector (not included) on the Die Grinder . T urn on the air compressor , and set its regulator to the recommended 90 PSI for t ...
-
Harbor Freight Tools 36572 - page 8
SKU 36572 For technical questions, please call 1-800-444-3353 P AGE 8 INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Always make sure the T rigger (15) is in its “OFF” position, and disconnect the Die Grinder from its compressed air supply before per- forming any inspection, adjustments, maintenance, or cleaning . 2. Before each use, inspec ...
-
Harbor Freight Tools 36572 - page 9
SKU 36572 For technical questions, please call 1-800-444-3353 P AGE 9 P ARTS LIST ASSEMBL Y DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only , and are not available individually as replacement parts. 31 ...
-
Harbor Freight Tools 36572 - page 10
90 Day W arranty Harbor Freight T ools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or i ...
Harbor Freight Tools 36572についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHarbor Freight Tools 36572の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 36572で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。