Pelco C586Mの取扱説明書

42ページ 0.48 mb
ダウンロード

ページに移動 of 42

Summary
  • Pelco C586M - page 1

    Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120 ® KBD4000V Genex ® Multiplexer Keyboar d Installation/ Operation Manual C586M (9/99) LIVE/VCR M ON ITO R N E A R F A R O PE N CLO SE ...

  • Pelco C586M - page 2

    2 Pelco Manual C586M (9/99) CONTENTS Section Page IMPORT ANT SAFEGUARDS AND WARNINGS ................................................................ 4 DESCRIPTION ................................................................................................................... 4 MODELS ............................................................. ...

  • Pelco C586M - page 3

    Pelco Manual C586M (9/99) 3 LIST OF ILLUSTRA TIONS Figur e Page 1 Rear Panel of KDB4000V Keyboard .................................................................. 7 2 KBD4000V Interface Mounting Hole Dimensions .............................................. 7 3 Connecting KBD4000V to a Multiplexer ................................................. ...

  • Pelco C586M - page 4

    4 Pelco Manual C586M (9/99) IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or ...

  • Pelco C586M - page 5

    Pelco Manual C586M (9/99) 5 MODELS KBD4000V Keyboard for pan, tilt and lens control of variable speed receivers. Includes 5-inch (12.7 cm) diagonal color monitor . 120 V AC, 60 Hz. KBD4000V -X Keyboard for pan, tilt, and lens control of variable speed receivers. Includes 5-inch (12.7 cm) diagonal color monitor . 230 V AC. 50 Hz. INST ALLA TION The ...

  • Pelco C586M - page 6

    6 Pelco Manual C586M (9/99) PROGRAMMING MODE Set switch 8 ON to program the multiplexer and camera presets and patterns from the keyboard. Set the switch OFF to disable programming. 3. Replace the cover on the back of the keyboard. 4. Peel off the protective coverings over the LED display and the LCD monitor on the keyboard. 5. Attach the KBD4000V ...

  • Pelco C586M - page 7

    Pelco Manual C586M (9/99) 7 Figure 2. KBD4000V Interface Mounting Hole Dimensions Figure 1. Rear Panel of KDB4000V Keyboard 2.5" (6.4 cm) RX+ RX- GND TX- TX+ 1234 ON VIDEO POWER ON OFF KBD4000V INTERF ACE INTERF ACE CABLE POWER SUPPL Y KBD4000V USER-SUPPLIED VIDEO COAX CABLE USER-SUPPLIED COMMUNICA TION CABLE 25 FOOT (7.6 M) DA TA CABLE MUL TI ...

  • Pelco C586M - page 8

    8 Pelco Manual C586M (9/99) POWER SUPPL Y KBD4000V INTERF ACE POWER SUPPL Y POWER SUPPL Y KBD4000V MUL TIPLEXER SERVER KBD4000V KBD4000V R+ R- T- T+ R+ R- T- T+ R+ R- T- T+ R+ R- T- T+ R+ R- T- T+ R+ R- T- T+ LOCAL KEYBO ARD MUX(S) VIDEO OUTPUTS 1 2 3 4 KBD4000V KBD4000V KBD4000V INTERF ACE KBD4000V KBD4000V KBD4000V INTERF ACE KBD4000V KBD4000V KB ...

  • Pelco C586M - page 9

    Pelco Manual C586M (9/99) 9 POWER SUPPL Y TO KBD4000V FROM MUL TIPLEXER SERVER R+ R- T- T+ LOCAL FIRST KBD W ALL BLOCK TERMINAL 1 2 3 4 5 6 7 8 SECOND KBD W ALL BLOCK TERMINAL 1 2 3 4 5 6 7 8 12 V A C W ALL TRANSFORMER USER- SUPPLIED CABLE 1 2 3 45 6 7 8 W ALL BLOCK TERMINALS TX+ TX- GND RX- RX+ 12 V A C W ALL TRANSFORMER KBD4000V INTERF ACE MUL TI ...

  • Pelco C586M - page 10

    10 Pelco Manual C586M (9/99) UNUSED Switches 4 and 5 are not used in the multiplexer server mode. They must be placed in the OFF position. TURBO MODE Set switch 6 ON to enable the turbo pan feature. Set the switch OFF to disable the turbo pan feature. CAMERA ADDRESS MODE There are two modes for addressing cameras: by addressing all the cameras cons ...

  • Pelco C586M - page 11

    Pelco Manual C586M (9/99) 11 OPERA TION IMPORT ANT NOTE ABOUT PROGRAMMING When the keyboard is plugged into a multiplexer or multiplexer server , the keyboard is ready to operate. However , some minimal programming may be r equired to make your system work. MUL TIPLEXER The default settings for the duplex and simplex multiplexers are not the same, ...

  • Pelco C586M - page 12

    12 Pelco Manual C586M (9/99) IMPORT ANT NOTE ABOUT DIFFERENCES IN SIMPLEX AND DUPLEX MUL TIPLEXER MODES OF OPERA TION The simplex multiplexer has three modes of operation: live, VCR, and record. • In the live mode, the main monitor can show live video both in full-screen or multiple-screen views. Y ou cannot record in the live mode. The multiplex ...

  • Pelco C586M - page 13

    Pelco Manual C586M (9/99) 13 1. LED DISPLA Y Displays the address of the multiplexer (from 1-16) with which the keyboard is communicating. 2. LIVE/VCR KEY Selects the source of video to display on the monitor(s). LIVE is live video from the cameras. VCR is recorded video that is played back from a VCR. The simplex multiplexer must be in the record ...

  • Pelco C586M - page 14

    14 Pelco Manual C586M (9/99) T able C. Operation Guide NOTE: References to switch 7 in this table refer to the switch behind the panel on the back of the keyboard. There are two modes for addressing cameras: by addressing all the cameras consecutively from 1-256 (switch 7 ON, refer to T able D) or by addressing the cameras in groups of 9 or 16 acco ...

  • Pelco C586M - page 15

    Pelco Manual C586M (9/99) 15 T able C. Operation Guide (Continued) 1. Go to the Advanced System Setup menu. 2. Move the joystick so the cursor highlights SPOT MONI- TOR DISPLA Y items. 3. Press the OPEN key until either SEQUENCE or BLANK is displayed. 4. Exit the Advanced System Setup menu. 1. Press the MAIN MONITOR key . The green LED over the MAI ...

  • Pelco C586M - page 16

    16 Pelco Manual C586M (9/99) T able C. Operation Guide (Continued) 1. Press the MAIN MONITOR key . The green LED over the MAIN key lights. 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connec ...

  • Pelco C586M - page 17

    Pelco Manual C586M (9/99) 17 T able C. Operation Guide (Continued) 1. Press the SPOT MONIT OR key . The green LED over the SPOT key lights. 2. Select a camera on the multiplexer that you want to sequence. Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to ...

  • Pelco C586M - page 18

    18 Pelco Manual C586M (9/99) 1. Follow the steps under “Run a sequence of cameras from one multiplexer on the MAIN monitor” or “Run a sequence of cameras from one multiplexer on the SPOT monitor” to start sequencing the cameras on the main and spot monitors of individual multiplexers that you want to sequence. 2. Hold down the SEQ key for a ...

  • Pelco C586M - page 19

    Pelco Manual C586M (9/99) 19 1. Press the SPOT MONIT OR key . The green LED over the SPOT key lights. 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT ...

  • Pelco C586M - page 20

    20 Pelco Manual C586M (9/99) 1. Press the MAIN or SPOT MONITOR key . The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLA Y menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section). 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) ...

  • Pelco C586M - page 21

    Pelco Manual C586M (9/99) 21 OPERA TION KEYBOARD COMMAND RESUL T T able C. Operation Guide (Continued) 1. Press the MAIN MONIT OR key . The green LED over the MAIN key lights. 2. On the number pad, press the address number of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then pre ...

  • Pelco C586M - page 22

    22 Pelco Manual C586M (9/99) PROGRAMMING This section applies only to programming the multiplexer . T o program the multiplexer server , refer to the server manual. Programming allows you to configure the multiplexer from the KBD4000V for the way that you want your system to operate. The multiplexer automatically selects the most common operating p ...

  • Pelco C586M - page 23

    Pelco Manual C586M (9/99) 23 MENUS T o program from the keyboard, the keyboard must be in main monitor mode. Press the MAIN MONITOR key . SYSTEM SETUP (View Key) T o program the main basic system parameters: 1. Press the MAIN MONITOR key . 2 . Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a mult ...

  • Pelco C586M - page 24

    24 Pelco Manual C586M (9/99) Record Speeds Sets the speed at which the VCR normally records video and the speed at which it records when there is an alarm(s). Setting the speeds in the System Setup menu also sets the speeds in the Record Setup and Custom VCR Setup menus. Main Monitor Video (Duplex Multiplexer Color Models Only) Composite is standar ...

  • Pelco C586M - page 25

    Pelco Manual C586M (9/99) 25 3. Press the VIEW key for approximately three seconds. The basic System Setup menu appears (refer to Figure 8). 4. The currently selected menu item blinks. Use the joystick to highlight ADV ANCED SETUP . 5. Press the OPEN key . The Advanced System Setup menu appears (refer to Figure 9). 6. Use the joystick to move betwe ...

  • Pelco C586M - page 26

    26 Pelco Manual C586M (9/99) SEQUENCE - Allows you to view an individual camera or run a sequence. An alarm or activity detection will override what you are observing. When the alarm or activity detection goes away , the screen will return to the camera or sequence you were viewing. TRACK MAIN - The spot monitor will follow the camera switching tha ...

  • Pelco C586M - page 27

    Pelco Manual C586M (9/99) 27 7. When you have completed all the changes you want to make, go to EXIT or BASIC SETUP . 8. Press the OPEN key to exit the programming mode or to go to the basic system setup menu. When HELP is highlighted, you may press the OPEN key to display a help screen that will tell you which keys to press to configure specific o ...

  • Pelco C586M - page 28

    28 Pelco Manual C586M (9/99) Figure 10. Basic VCR Setting Menu T able E. VCR T ypes NTSC P AL UNIVERSAL UNIVERSAL GYYR TLC1800 ASUT A TL VCR 251 GYYR 2100 ASUTSA TL VCR 964 GYYR 2100 HD MODE BURLE TC3910X JVC SR-L900U HIT ACHI VTL30E JVC SR-L901U HIT ACHI VT -L1000E JVC SR-9070U HIT ACHI VT -L2000E JVC BR-S925U JVC BR9060E MITSUBISHI HS7424U JVC BR ...

  • Pelco C586M - page 29

    Pelco Manual C586M (9/99) 29 CUSTOM VCR SETUP (Live/VCR Key) T o program the advanced VCR parameters: 1. Press the MAIN MONITOR key . 2 . Use the number keypad to enter the address of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a server), then press the UNIT key . 3. Press the LIVE/VCR ke ...

  • Pelco C586M - page 30

    30 Pelco Manual C586M (9/99) CAMERA SETUP (Number and CAM Keys) T o program a camera input: 1. Press the MAIN MONITOR key . 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a. On the number keypad, enter the address number of the multiplexer (1-16 if the keyboard is connected to a multiplexer; 1-8 if the keyboard is connected to a ser ...

  • Pelco C586M - page 31

    Pelco Manual C586M (9/99) 31 Coaxitron Format EXTENDED - Use when your system has moveable cameras controlled by 32-bit Coaxitron receivers, such as Esprit, Intercept, Spectra, and LRD41C21/LRD41C22 Series. OFF - Use when your system has fixed cameras only . ST ANDARD - Use when your system has moveable cameras controlled by 15-bit Coaxitron receiv ...

  • Pelco C586M - page 32

    32 Pelco Manual C586M (9/99) ACTIVITY DETECTION MASK SETUP Activity detection continually monitors selected camera inputs for motion. When motion is detected, the multiplexer increases the frequency with which that camera(s) is shown and recorded. Activity detection is most ef fective when only a few cameras are showing activity . As the number of ...

  • Pelco C586M - page 33

    Pelco Manual C586M (9/99) 33 7. T urn activity boxes on or off (by default, all activity boxes are on). T o turn on all activity boxes, use the joystick to choose SET ALL. Press the OPEN key . All boxes will contain a symbol as shown in Figure 13. The multiplexer will monitor motion in those boxes. T o turn off all activity boxes, use the joystick ...

  • Pelco C586M - page 34

    34 Pelco Manual C586M (9/99) HELP MENU The Help menu is accessed from any other menu. 1. Use the joystick in any menu to highlight HELP . 2. Press the OPEN key . The Help menu appears. Figure 14. Camera Sequence Menu Figure 15. Help Menu GROUP QUAD (2x2) 1 04 2 04 3 04 4 04 NINE (3x3) 04 04 VCR/LIVE * * SIMPLEX MULTIPLEXERS SHOW “DISP/REC”. PRE ...

  • Pelco C586M - page 35

    Pelco Manual C586M (9/99) 35 MUL TIPLE CAMERA DISPLA Y SETUP The multiple camera display formats may be configured using the keyboard. The LEDs above the camera buttons on the multiplexer will illuminate to indicate which cameras are being displayed. PROGRAMMING THE PICTURE-IN-PICTURE DISPLA Y ( Key) The on-screen location and size of the picture-i ...

  • Pelco C586M - page 36

    36 Pelco Manual C586M (9/99) PROGRAMMING THE 9-CAMERA DISPLA Y ( Key) Y ou can program two groups of nine cameras each. Both groups can be programmed to include any nine cameras. is not available in simplex RECORD mode. T o program the nine-camera displays: 1. Press the MAIN MONITOR key . 2 . Use the number keypad to enter the address of the multip ...

  • Pelco C586M - page 37

    Pelco Manual C586M (9/99) 37 PROGRAMMING MENU DEF AUL TS T able F . Programming Menu Defaults Menu Item Default System Setup T ime Display On T itle Display On Normal Record Speed 2/6/8 Hr (NTSC/EIA) 3 Hr (P AL/CCIR) Alarm Record Speed 2/6/8 Hr (NTSC/EIA) 3 Hr (P AL/CCIR) Main Monitor Video (Duplex Only) Composite Main Monitor Display High Resoluti ...

  • Pelco C586M - page 38

    38 Pelco Manual C586M (9/99) PROGRAMMING A PRESET 1 . Press the MAIN or SPOT MONIT OR key . The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLA Y menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section). 2 . Select the camera. Addressing by Mu ...

  • Pelco C586M - page 39

    Pelco Manual C586M (9/99) 39 TROUBLESHOOTING If you have difficulty operating your system, run through the following checklist to see if you can solve the problem. 1. Are the keyboard switches set properly? 2. Is the equipment wired properly? 3. Are the menu options in the multiplexer(s) and server set properly? 4. Has the multiplexer been set to t ...

  • Pelco C586M - page 40

    40 Pelco Manual C586M (9/99) 17. If you have a server and cannot change between full screen and multiple screen views on the main monitor , check the MAIN MONIT OR CONTROL setting in the Monitor menu of the server . 18. If the UNIT ID, in the ADV ANCED SYSTEM SETUP menu, is inadvertently changed at the keyboard resulting in an uncontrollable sequen ...

  • Pelco C586M - page 41

    Pelco Manual C586M (9/99) 41 SPECIFICA TIONS ELECTRICAL Input V oltage: +12 VDC @ 1A Power Consumption: 8 watts Joystick: Three-axis, vector solving, with twisting, return-to-center head Data Interface: RS-485, 25-foot (7.6 m) cable supplied Data Connector T ype: RJ-45, 8-pin modular (female) Digital Display: T wo red seven-segment LEDs Main/Spot M ...

  • Pelco C586M - page 42

    42 Pelco Manual C586M (9/99) REVISION HISTOR Y Manual # Date Comments C586M 9/99 Original version. Pelco, the Pelco Logo, Camclosure, Esprit, Genex, Intercept, Legacy , and Spectra are registered trademarks of Pelco. © Copyright 1999, Pelco. All rights reserved. Endura and ExSite are trademarks of Pelco. U.S. Patent No. 41 1,530. PRODUCT WARRANTY ...

メーカー Pelco カテゴリー Electronic Keyboard

Pelco C586Mのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- C586Mの取扱説明書
- Pelcoの製品カード
- パンフレット
- またはPelco C586Mの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pelco C586Mの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pelco C586Mの取り付け説明書、サービスマニュアル、簡易説明書、またはPelco C586Mのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pelco C586Mの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pelco C586Mデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPelco C586Mを使用するのを助ける技術的文書のことです。説明書は通常、全てのPelco C586Mユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pelcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pelco C586Mの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPelco C586Mの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pelco C586Mに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pelco C586Mデバイスの基本機能を使うにあたってのヒント。 Pelco C586Mのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pelco C586Mに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPelco C586Mのメーカー/サービスへの連絡先に関する情報。

Pelco C586Mについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPelco C586Mの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco C586Mで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)