IMC Networks FiberLinXの取扱説明書

32ページ 0.62 mb
ダウンロード

ページに移動 of 32

Summary
  • IMC Networks FiberLinX - page 1

    19772 P auling  F oothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000  F AX: (949) 465-3020 www .imcnetworks.com F iberLinX Installation Manual and User Reference Guide Document Number 50-80111-01 A0 February 2000 ...

  • IMC Networks FiberLinX - page 2

    Disclaimer IMC Networks makes no warranties with respect to this document and disclaims any implied warranties of merchantability or fitness for a particular purpose. IMC Networks assumes no responsibility for any errors that may appear in this document or for incidental consequential damages in connection with the performance or use of this materi ...

  • IMC Networks FiberLinX - page 3

    Contents Chapter 1: Introduction About FiberLinX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.1 About FiberLinX Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2 How FiberLinX Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2 Chapter 2: Hardware Installation ...

  • IMC Networks FiberLinX - page 4

    Example 3: Fiber Conversion and Highly Secure Remote Management Between Two Copper-Based Switches . . . . . . . . . .4.3 Chapter 5: Technical Specifications Fiber Optic Cleaning Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . .5.1 Electrostatic Discharge Precautions . . . . . . . . . . . . . . . . . . . . . . . . .5.1 Unit Specificat ...

  • IMC Networks FiberLinX - page 5

    Chapter 1: Introduction About F iberLinX FiberLinX from IMC Networks is an IEEE 802.3 compliant, SNMP- manageable media converter/LAN extender/Ethernet bridge that can be managed remotely. FiberLinX is designed to convert between 10 Mbps Ethernet twisted pair (10Base-T) and 10 Mbps Ethernet (10Base-FL) single- mode or multi-mode fiber optic cabl ...

  • IMC Networks FiberLinX - page 6

    1.2 See Chapter 4 of this guide for more example FiberLinX installations. About F iberLinX Modules FiberLinX Modules can be installed into any IMC Networks PowerChassis/100-Series. The following versions of FiberLinX Modules are available: FiberLinX  10Base-T twisted pair and 10Base- FL 850 nm multi-mode fiber; includes two RJ-45 connectors and ...

  • IMC Networks FiberLinX - page 7

    Chapter 2: Hardware Installation Installing a FiberLinX Module involves the following steps: 1) Configuring the FiberLinX Module via its eight-position Dip switch for the following: l Half/Full Duplex setting (data ports only), l designating the management traffic port, l host/remote or standalone operation; 2) Installation of a PowerChassis/100-Se ...

  • IMC Networks FiberLinX - page 8

    The following table shows the function for each of the eight Dip switches on FiberLinX . Refer to the section on each feature for specific configuration information . Switches 1 & 2: Fiber Optic Type These Dip switch settings are configured at the factory and should NOT be changed in the field. Switches 3 & 4: Selecting Duplex Mode Each dat ...

  • IMC Networks FiberLinX - page 9

    Switches 7 & 8: Configuring FiberLinX as a Host, Remote or Standalone Unit When two FiberLinX units are paired with one another, each FiberLinX unit can be configured to be either a Host unit or a Remote unit. As a Host, FiberLinX requests management information from any attached remote unit and displays that information, along with its own, up ...

  • IMC Networks FiberLinX - page 10

    receiving a fiber link, FiberAlert disables the media converter's fiber transmitter, thus mirroring the link status of the opposite end of the fiber. Both fiber link LEDs on either side of the devices should extinguish, alerting you to the fault. NOTE: FiberAlert should only be activated on one side of a media conversion. More information on F ...

  • IMC Networks FiberLinX - page 11

    Selecting a Crossover/P ass- Through Connection Once a FiberLinX is installed, you can select a crossover workstation or pass-through repeater/hub connection for the twisted pair data port. FiberLinXs twisted pair data port has one RJ-45 connector for a single shielded or unshielded twisted pair link segment and features a push-button switch, lo ...

  • IMC Networks FiberLinX - page 12

    FAR TP LINK Glows green when a link is established on remote (far-end) TP data port. SNMP Blinks green with SNMP activity. TP ACT Blinks green with TP activity. NOTE: The FAR CPU UP LED and the FAR TP LNK LED only function when two FiberLinX are connected to one another (i.e., Host and Remote). DB-9 Serial Connector FiberLinX features a DB-9 serial ...

  • IMC Networks FiberLinX - page 13

    Chapter 3: Configuring and Managing F iberLinX This chapter details the steps you must complete to configure and manage your FiberLinX . Required Management Configuration Steps In order for the installed FiberLinX to be managed using iView or another network management software (NMS) application, the following steps need to be completed: 1) Hardwar ...

  • IMC Networks FiberLinX - page 14

    HUBCTRL32 HUBCTRL32 (Hub Control 32) is an in-band configuration utility created by IMC Networks that lets users quickly and easily complete the first stages of SNMP configuration for IMC Networks SNMP-manageable devices. Tasks HUBCTRL32 can perform include:  setting the IP address, subnet mask and default gateway;  defining the community ...

  • IMC Networks FiberLinX - page 15

    System Requirements To run iView for FiberLinX , the management PC must be equipped with the following:  20 MB free disk space, 32 MB RAM as well as one of the following operating systems:  Windows TM 95/98/NT (standalone or with OpenView)  HP-UX and OpenView  IBM AIX and NetView or OpenView  Solaris and OpenView Please consult the i ...

  • IMC Networks FiberLinX - page 16

    Once in OpenView , highlight the F iberLinX icon and select the T ools , F iberLinX ; OpenView will then launch iView . If NO T Using iView NOTE: Installation of SNMP software differs from one package to another. This section describes the steps required to integrate the IMC Networks agent with other management software. For instal- lation details ...

  • IMC Networks FiberLinX - page 17

    Chapter 4: Application Examples FiberLinX can be used in many configurations based upon application, network architecture and management security requirements. The following are several examples of how you can use FiberLinX in your network. Example 1: Direct Fiber Switch Connection from Central to Remote Site To achieve remote management and monito ...

  • IMC Networks FiberLinX - page 18

    Example 2: Fiber Conversion and Remote Management Between Two Copper -Based Switches In this situation, configure the Central sites unit as a Host with management traffic through the twisted pair data port, and the Remote site's unit to accept management traffic through the fiber data port. Note that the twisted pair management ports on bot ...

  • IMC Networks FiberLinX - page 19

    Example 3: Fiber Conversion and Highly Secure Remote Management Between Two Copper -Based Switches For the highest level of management security, route SNMP management traffic completely away from the switch. Two FiberLinX units are also used in this configuration. The following illustration shows an external hub being used to maintain LAN separatio ...

  • IMC Networks FiberLinX - page 20

    4.4 ...

  • IMC Networks FiberLinX - page 21

    Chapter 5: T echnical Specifications F iber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust which can obstruct the optic path and cause performance degradation. Good system performance requires clean optics and connector ferrules. 1) Use fiber patch cords (or c ...

  • IMC Networks FiberLinX - page 22

    WARNING! Integrated circuits and fiber optic components are extremely susceptible to electrostatic discharge damage. Do not handle these components directly unless you are a qualified service technician and use tools and techniques that conform to accepted industry practices. 3) Hold boards by the edges only; do not touch the electronic components ...

  • IMC Networks FiberLinX - page 23

    Chapter 6: General Information T echnical Support IMC Networks technical support is available at: Phone: (949) 465-3000 or (800) 624-1070 (U.S.); +32-16-550880 (Europe) FAX: (949) 465-3020 E-Mail: techsupport@imcnetworks.com Web: www.imcnetworks.com W arranty IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF S ...

  • IMC Networks FiberLinX - page 24

    Networks, freight, customs and handling charges pre-paid. End-user agrees to accept all liability for loss of or damages to the returned product during shipment. IMC Networks shall repair or replace the returned product, at its option, and return the repaired or new product to the end-user, freight prepaid, via method to be determined by IMC Networ ...

  • IMC Networks FiberLinX - page 25

    F ederal Communications Commission Radio F requency Interference Statement This equipment has been tested and found to comply with the limits for a Class A computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial env ...

  • IMC Networks FiberLinX - page 26

    6.4 ...

  • IMC Networks FiberLinX - page 27

    Appendix Assigning IP Information to F iberLinX Using DB-9 Serial Port The serial port uses an IBM-compatible DB-9 serial connector. To connect the device to your terminal/computer, use a DB 9-pin male/female null modem cable. (If your computer/terminal has a serial port using a connection not compatible with a DB-9 COM port, use the Pin Connection ...

  • IMC Networks FiberLinX - page 28

    Command List  I = Enter New Saved Parameter Values  P = Change Password  T = New Trap Destination  K = Remove ALL Trap Destinations  C = New Community String  U = Delete ALL Community Strings  E = End Session NOTE: You must reboot after making any modifications to the Saved Values or changes will not take effect. To reboot, typ ...

  • IMC Networks FiberLinX - page 29

    Deleting Communities To delete all community strings and start over, press U . You will then be asked, Are you sure you want to delete all future strings? Press Y to proceed, N to abort. Press Enter . NOTE: The above function will delete ALL community strings. If you want to be able to selectively delete community strings, use HUBCTRL32 to co ...

  • IMC Networks FiberLinX - page 30

    HUBCTRL32 Installation Instructions Software and Hardware Requirements HUBCTRL32 for Windows NT requires the following: l Windows NT version 4.0 or higher. l The same hardware requirements for Windows NT plus a network interface card. l Internet Explorer 4.0 service pack 2 or higher required for the Help to work. HUBCTRL32 for Windows 98 requires t ...

  • IMC Networks FiberLinX - page 31

    Installing HUBCTRL32 Once the setup is launched: 1) Another Welcome dialog box for the HUBCTRL32 Setup Program will appear. NOTE: It is strongly recommended that you exit all Windows applications before continuing. Click Next to continue, Cancel to exit the installation process. 2) The License Agreement dialog box will appear. Click Yes to accept t ...

  • IMC Networks FiberLinX - page 32

    9) As stated earlier, the Networking Control Panel application will launch once you finish the Setup Utility. Here you must install the drivers necessary for running HUBCTRL32. At this window, do the following: For Windows 98 Network Control Panel Application A) Highlight an adapter to bind HUBCTRL32 to. B) Click the Add... button. C) Select Protoc ...

メーカー IMC Networks カテゴリー Power Supply

IMC Networks FiberLinXのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- FiberLinXの取扱説明書
- IMC Networksの製品カード
- パンフレット
- またはIMC Networks FiberLinXの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、IMC Networks FiberLinXの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、IMC Networks FiberLinXの取り付け説明書、サービスマニュアル、簡易説明書、またはIMC Networks FiberLinXのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、IMC Networks FiberLinXの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

IMC Networks FiberLinXデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがIMC Networks FiberLinXを使用するのを助ける技術的文書のことです。説明書は通常、全てのIMC Networks FiberLinXユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

IMC Networksの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. IMC Networks FiberLinXの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははIMC Networks FiberLinXの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。IMC Networks FiberLinXに関してこのドキュメントで見つけることができる全てのヒントの目次
3. IMC Networks FiberLinXデバイスの基本機能を使うにあたってのヒント。 IMC Networks FiberLinXのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。IMC Networks FiberLinXに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるIMC Networks FiberLinXのメーカー/サービスへの連絡先に関する情報。

IMC Networks FiberLinXについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもIMC Networks FiberLinXの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがIMC Networks FiberLinXで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)