Curtis Computer 833の取扱説明書

21ページ 0.08 mb
ダウンロード

ページに移動 of 21

Summary
  • Curtis Computer 833 - page 1

    MODEL 833 “FUEL ” GAGE/HOUR METER W/“PUSH- Read Instructions Carefully ! ® ! ...

  • Curtis Computer 833 - page 2

    Saf ety Instructions This instrument was manuf actured and tested according to the applicable technical standards . It complies with all the safety regulations as shipped from the f actory . Installation and star tup must be performed by skilled personnel. F ailure to install and operate the unit in accordance with these instructions may result in ...

  • Curtis Computer 833 - page 3

    ! T ABLE OF CONTENTS P age 1. Model Encodement 2 2. T echnical Specifications 2.1 Electrical 4 2.2 Mechanical 5 2.3 Environmental 6 3. Installation 7 4. Operation 14 5. T roubleshooting 16 6. Maintenance 17 ...

  • Curtis Computer 833 - page 4

    2 1. MODEL ENCODEMENT 833RB vvvv w V oltage 0024 Reset lev el B = 2.09 VPC ...

  • Curtis Computer 833 - page 5

    3 xy zzzz ! Discharge profile C = Adjustable (See T able 3.) Output J = N.C. holding rela y Contact rating = 3 Amps when continuously closed, 1 Amp when opening 316O O = Cur tis logo ...

  • Curtis Computer 833 - page 6

    4 2. TECHNICAL SPECIFICA TIONS 2.1 Electrical Operating Range ± 25% of nominal voltage Operating Current V oltage (volts) Nominal Current (mA) Maximum Current (mA) 24 18 28 Rela y Contact Ratings V oltage: 200 VDC (max) Current: 1 ADC (max) (3 ADC max when continuously closed) Po we r: 50 W (max) ! ...

  • Curtis Computer 833 - page 7

    2.2 Mechanical Displa y Battery state-of-charge: 10-bar , tr i-color LED Hour Meter: 6-digit LCD , 5mm high Resolution Hour Meter 99,999.9 Hours Hardware Kit Mounting brack et, thumbnuts or M4 He x nuts (2), lock w ashers (2), mating connector Molex No . 39-01-2085, w/pins No . 39-00-0039, no connectors in bulk shipments . P anel Cutout 52mm, 2 1 / ...

  • Curtis Computer 833 - page 8

    6 2.3 En vironmental T emperature Operating: - 4 0 ° C t o + 65 ° C (Standard Mode) -10° C to +65° C (Push-to-read Mode) Storage: - 5 0 ° C t o + 9 0 ° C Humidity 95% RH (Non Condensing) at 38°C Shock & Vibration 2.2 G, 20-200 Hz; 20 minute period; X,Y ,Z, 13 cycles each Enclosure IP65 (face) ! ...

  • Curtis Computer 833 - page 9

    7 ! 3. INST ALLA TION The Model 833 Installation Kit includes a pre-assembled mating connector with 5” ter minated wires. Ask for Curtis Part Number 15369002. The Model 833 fits into a dash-panel cutout measuring 2 1 / 16 ” (52 mm). Te r minal Assignment (see diagr am on page 13) Pin 8 = Battery + Pin 8 to battery + ...

  • Curtis Computer 833 - page 10

    8 ! Pin 5 = Battery – Connect to battery ground as close to batter y as possible . Pin 2 = Keys witch The ke yswitch turns on and off the LED displa y of the battery discharge indicator. Monitoring of the batter y continues when Pin 2 is turned off and the display is not lit. The hour meter display is unaff ected by Pin 2, although it cannot accu ...

  • Curtis Computer 833 - page 11

    9 Pin 3 = Relay (+) Pin 3 connects in series with the lift coil circuit (or the circuit to be switched at empty). For holding rela y (J), Pin 3 must be electrically closer to batter y + than Pin 4 Pin 4 = Relay (–) Pin 4 also connects in series with the circuit to be s witched at empty . ...

  • Curtis Computer 833 - page 12

    Ta b le 1. Hour Meter Contr ol Lines & Impedance Specifications Model Lo w V olt a ge High V oltage Min. Impedance Maximum Minim um HRM+ HRM- 24 VDC 5.0 VDC 15.0 VDC 90 k Ω 30 k Ω Ta b le 2. Hour Meter Contr ol Logic Key HRM HRM HRM Hour Icon s witch (+) (+) (+) meter Off x x x Display only Steady On V H xx On Flashing On x V H xO nF lashin ...

  • Curtis Computer 833 - page 13

    ! 11 NO TE : Fuses and Wires Regulations may require that the Model 833 be fused. If installing a fuse, use a 10A fuse wired with 1.5mm or equivalent wire . The voltage drop across the fuse , its holder , and connectors must be less than 1% of the nominal system voltage . Discharge Adjustments Ta b le 3 lists the voltages per cell under load that c ...

  • Curtis Computer 833 - page 14

    12 CUR TIS Model 833 Rear Vie w ! ...

  • Curtis Computer 833 - page 15

    13 Connections f or T ypical Model 833 Application V ehicle system voltage is the higher of the two oper ating vo ltages of a dual voltage unit. Hour meter measures “ke yswitch on” time. ! ...

  • Curtis Computer 833 - page 16

    14 4. OPERA TION Displa y The Cur tis Model 833 combines in one instrument a completely solid state LED battery state-of-charge indicator , an LCD hour meter , and lift lockout. Only when battery is proper ly charged is right most LED (1) lit. As battery’s state-of-charge decreases , successive LEDs light up , one at a time. 2nd from left LED fla ...

  • Curtis Computer 833 - page 17

    15 Push-to-read When the front button is depressed, the LCD will displa y the hour meter reading for 6 seconds min. The hour meter will not accumulate time during this operation. Reset type/le v el (after or during recharge) CTR = Charge T racking Reset If the gage is connected to the battery dur ing recharge, the gage will track the battery charge ...

  • Curtis Computer 833 - page 18

    16 5. T r oubleshooting The follo wing checklist should help y ou to troubleshoot an y problems with the instrument. Problem P ossible Causes No display T er minals not connected or improper voltage Stays at FULL Instrument voltage does not match battery voltage, B+ connected to the wrong terminal Will not reset Instrument voltage does not match ba ...

  • Curtis Computer 833 - page 19

    17 6. Maintenance Model 833 Series is not ser viceable in the field. Units returned to the factory within the warranty period (see inside backco ver) will be replaced without charge. ...

  • Curtis Computer 833 - page 20

    Guarantee - Cur tis Instruments’ products and/or components are guaranteed against def ects in workmanship and material f or a period of two y ears, or as defined in the individual product literature, from date of shipment from our f actory , when applied in a proper application within specified ratings. This guarantee is limited to repair or rep ...

  • Curtis Computer 833 - page 21

    CURTIS INSTRUMENTS, INC. 200 Kisco A venue, Mt. Kisco, NY 10549 T el. (914) 666-2971 • FAX (914) 666-2188 53024 REV A 7/01 ...

メーカー Curtis Computer カテゴリー Marine Instruments

Curtis Computer 833のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 833の取扱説明書
- Curtis Computerの製品カード
- パンフレット
- またはCurtis Computer 833の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Curtis Computer 833の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Curtis Computer 833の取り付け説明書、サービスマニュアル、簡易説明書、またはCurtis Computer 833のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Curtis Computer 833の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Curtis Computer 833デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCurtis Computer 833を使用するのを助ける技術的文書のことです。説明書は通常、全てのCurtis Computer 833ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Curtis Computerの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Curtis Computer 833の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCurtis Computer 833の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Curtis Computer 833に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Curtis Computer 833デバイスの基本機能を使うにあたってのヒント。 Curtis Computer 833のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Curtis Computer 833に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCurtis Computer 833のメーカー/サービスへの連絡先に関する情報。

Curtis Computer 833についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCurtis Computer 833の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCurtis Computer 833で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)