Transition Networks SSDTF1022-105の取扱説明書

9ページ 0.7 mb
ダウンロード

ページに移動 of 9

Summary
  • Transition Networks SSDTF1022-105 - page 1

    Installation . . . . . . . . . . . . . . . . . . . . .3 Operation . . . . . . . . . . . . . . . . . . . . . .9 Cable Specifications . . . . . . . . . . . . .10 Technical Specifications . . . . . . . . . .12 Troubleshooting . . . . . . . . . . . . . . . .13 Compliance Information . . . . . . . . .16 * Typical maximum cable distance. (Actual distance ...

  • Transition Networks SSDTF1022-105 - page 2

    2 SSDTF10xx-10x (TX) = transmit (RX) = receive * Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network. ** SSDTF1029-105 and -106 are intended to be installed in the same network where one is the local device and the other is the remote device. *** SSDTF1029-107 and -108 are intended to be ins ...

  • Transition Networks SSDTF1022-105 - page 3

    4 SSDTF10xx-10x Installation -- Continued Set the loop-back switch Hardware mode: The loop-back switch is located on the front panel of the device and is used for installation and network debugging procedures. To set the switch, use a small flat-blade screwdriver or a similar device (see the drawing to the right). CL (Copper loop-back) Enable loop- ...

  • Transition Networks SSDTF1022-105 - page 4

    6 SSDTF10xx-10x Installation -- Continued Settings for T1 configuration (right switch set, SW 1) T1/long-haul signal Use switches 3 and 4 on the left switch set to select T1/long-haul signal (see the drawing below). Use switches 1 and 2 on the right switch set to select the proper network cable settings. The drawing below lists the four options. -1 ...

  • Transition Networks SSDTF1022-105 - page 5

    8 SSDTF10xx-10x Installation -- Continued Install the copper cable 1. Locate or build twisted-pair copper cables that are compliant with the specifications on page 11 with RJ-45 connectors at both ends. 2. Ensure that the MDI/MDI-X switch is set according to the network conditions (see page 3) . 3. Connect the RJ-45 connector at one end of cable to ...

  • Transition Networks SSDTF1022-105 - page 6

    10 SSDTF10xx-10x Cable Specif ications Fiber cable Single mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm SSDTF1011-105 850 nm multimode Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm Fiber Optic Receiver Sensitivity: min: -32.5 dBm max: -14.0 dBm Link ...

  • Transition Networks SSDTF1022-105 - page 7

    12 SSDTF10xx-10x T echnical Specifications For use with Transition Networks Model SSDTF10xx-10x or equivalent Standards: Emissions: CISPR A; Telecordia TR-NWT-001089 (designed to meet; NOT tested) ; FCC Part 68; T1/E1 Physical layer: ITU-T, ANSI, AT&T, and ETSI; European Technical Standard: TBR 12; British Technical Publication: PD 7024 : 1994 ...

  • Transition Networks SSDTF1022-105 - page 8

    14 SSDTF10xx-10x 4. Is data transfer failing? YES • Verify the local copper connection by starting a local copper loop-back (hardware mode: set the loop-back switch on the local device to “CL”, software mode: enter the local copper loop-back command) and then use a bit error test unit to run a bit error test. • Verify the local fiber connec ...

  • Transition Networks SSDTF1022-105 - page 9

    Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial ...

メーカー Transition Networks カテゴリー Network Card

Transition Networks SSDTF1022-105のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SSDTF1022-105の取扱説明書
- Transition Networksの製品カード
- パンフレット
- またはTransition Networks SSDTF1022-105の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Transition Networks SSDTF1022-105の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Transition Networks SSDTF1022-105の取り付け説明書、サービスマニュアル、簡易説明書、またはTransition Networks SSDTF1022-105のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Transition Networks SSDTF1022-105の製品を使用するにあたって最も人気のある説明書を閲覧できます。

Transition Networks SSDTF1022-105デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがTransition Networks SSDTF1022-105を使用するのを助ける技術的文書のことです。説明書は通常、全てのTransition Networks SSDTF1022-105ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Transition Networksの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Transition Networks SSDTF1022-105の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははTransition Networks SSDTF1022-105の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Transition Networks SSDTF1022-105に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Transition Networks SSDTF1022-105デバイスの基本機能を使うにあたってのヒント。 Transition Networks SSDTF1022-105のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Transition Networks SSDTF1022-105に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるTransition Networks SSDTF1022-105のメーカー/サービスへの連絡先に関する情報。

Transition Networks SSDTF1022-105についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもTransition Networks SSDTF1022-105の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTransition Networks SSDTF1022-105で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)