-
Sabrent USBDSC5 - page 1
Sabre nt USB ‐ DSC5 USB 2.0 to SATA/IDE Hard Dr ive Adapter 2.5” Notebook IDE Hard Drive 1. Connect th e short 2.5” IDE conne ctor from the Sabrent adapter to the pins on your 2.5” Hard Drive. Note the keye ...
-
Sabrent USBDSC5 - page 2
Figure D: ...
-
Sabrent USBDSC5 - page 3
2. Connect th e USB cable from the USB ‐ DSC5 to an availabl e USB port on your computer. Figure A: 3. In most cases, the USB cable will supply sufficient power for the drive to spin up and initiate. ...
-
Sabrent USBDSC5 - page 4
Figure B: Figure C: Figure D: ...
-
Sabrent USBDSC5 - page 5
Figure E: Figure F: ...
-
Sabrent USBDSC5 - page 6
Figure G: 3.5” Desktop IDE Hard Drive 1. Most 3.5” IDE Hard Drives have Jumpers. Make sure they are set to Master Only . (Note: Pleas e refer to the drive manufacturer’s website for more information regar ...
-
Sabrent USBDSC5 - page 7
2. Connect the ID E power adapter dir ec tly in the IDE drive: Figure A: Figure B: Figure C: ...
-
Sabrent USBDSC5 - page 8
Figure D: 3. Connect the long 3.5 inch IDE c onnector to the pins on your hard drive. Note the keyed pin and slot and make sure that th e dri ve and the device line up properly and are securely ...
-
Sabrent USBDSC5 - page 9
Figure C: 4. Connect the US B cable from the DSC5 to a USB port on your comp uter. Figure A: ...
-
Sabrent USBDSC5 - page 10
2.5/3.5 Inch SATA Drive 1. Connect th e Sabrent converter to the power adapte r, and then plug the SATA po wer end into the SATA drive directly: Figure A: Figure B: ...
-
Sabrent USBDSC5 - page 11
Figure C: Figure D: Figure E: ...
-
Sabrent USBDSC5 - page 12
2. Connect th e SATA data cable into the Sabrent Converter, and the n connect the other en d directly into the SATA drive: Figure A: Figure B: Figure C: ...
-
Sabrent USBDSC5 - page 13
Figure D: Figure E: Figure F: ...
-
Sabrent USBDSC5 - page 14
3. Connect th e USB cable from the Sabrent converter to an available USB port on your comput er. Figure A: ...
-
Sabrent USBDSC5 - page 15
Hard Dri ve Setup For Win dow s 2000/XP/VISTA/7, no drivers or softwa re are ne cessarry. If the Hard ‐ Drive is brand new you may need to initialize it first in ord er to cause the Drive Letter to appe ar: 1. Cl ...
-
Sabrent USBDSC5 - page 16
4. At the following prom pt, click “Next”: 5. Click “Next”: ...
-
Sabrent USBDSC5 - page 17
6. Assign a drive letter to the drive, the n click “Next”: 7. Click on “F ormat this volume with the following settings:” Change the “File system” to “NTFS”. Change the “Volume label” to what ? ...
-
Sabrent USBDSC5 - page 18
8. Click “Finish”. Windows will now begin formatting and initializing the di sk: 9. Open “My Computer” and verify that the drive shows up properly: ...
-
Sabrent USBDSC5 - page 19
If the driv e has already been formatted, you can skip these steps. 1. Check the “Device Manager” to make sure that the “USB Mass Sto rage Device” driver appe ars under the “Unive rsal Serial Bus Controllers? ...
-
Sabrent USBDSC5 - page 20
...
Sabrent USBDSC5についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもSabrent USBDSC5の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSabrent USBDSC5で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。