Cabletron Systems EPIM F3の取扱説明書

44ページ 0.8 mb
ダウンロード

ページに移動 of 44

Summary
  • Cabletron Systems EPIM F3 - page 1

    FOT-F3 FIBER OPTIC TRANSCEIVER USER’S MANUAL ...

  • Cabletron Systems EPIM F3 - page 2

    ...

  • Cabletron Systems EPIM F3 - page 3

    FOT-F3 USER’S MANUAL i NO TICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is ...

  • Cabletron Systems EPIM F3 - page 4

    ii FOT-F3 USER’S MANUAL FCC NO TICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested ...

  • Cabletron Systems EPIM F3 - page 5

    FOT-F3 USER’S MANUAL iii VCCI NO TICE This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial and/or indust ...

  • Cabletron Systems EPIM F3 - page 6

    iv FOT-F3 USER’S MANUAL DECLARATION OF CONFORMITY Application of Council Directi ve(s): 89/336/EEC 73/23/EEC Manufacturer’ s Name: Cabletr on Systems, Inc. Manufacturer’ s Address: 35 Industrial W ay PO Box 5005 Rochester , NH 03867 European Representati ve Name: Mr . J . Solari European Representati ve Address: Cabletr on Systems Limited Nex ...

  • Cabletron Systems EPIM F3 - page 7

    FOT-F3 USER’S MANUAL v CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL ...............................................................1-1 1.2 CONVENTIONS .........................................................................1-2 1.3 OVERVIEW OF THE FOT-F3 ....................................................1-2 1.3.1 Connections .......... ...

  • Cabletron Systems EPIM F3 - page 8

    CONTENTS vi FOT-F3 USER’S MANUAL CHAPTER 4 TESTING AND TROUBLESHOOTING 4.1 INSTALLATION CHECK-OUT ................................................... 4-1 4.1.1 Testing the Fiber Optic Link Segment ........................ 4-1 4.1.2 Testing the FOT-F3 Fiber Optic Transceiver ............. 4-3 4.2 USING LANVIEW ..................................... ...

  • Cabletron Systems EPIM F3 - page 9

    FOT-F3 USER’S MANUAL 1-1 CHAPTER 1 INTR ODUCTION Welcome to Cabletron Systems FOT-F3 Fiber Optic Transceiver User’s Manual . This manual serves as a simple installation and reference guide for the FOT-F3 transceiver. You should have a general working knowledge of Ethernet or IEEE 802.3 type data communications networks and their physical layer ...

  • Cabletron Systems EPIM F3 - page 10

    CHAPTER 1: INTRODUCTION 1-2 FOT-F3 USER’S MANUAL Chapter 4, T esting and T r oubleshooting , contains procedures for verifying the proper installation of the FOT-F3. It also describes LANVIEW LEDs and their function. Appendix A, Specifications , provides the specifications for the FOT-F3 transceiver. 1.2 CONVENTIONS The following conventions are ...

  • Cabletron Systems EPIM F3 - page 11

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-3 Figure 1-1 FOT-F3 1.3.1 Connections The FOT-F3 connects two active Ethernet devices using an AUI cable and a fiber optic link segment. Devices such as repeaters, multiport repeaters, multiport transceivers or host systems are connected using fiber optic cables. The FOT-F3 is fully compatible with IE ...

  • Cabletron Systems EPIM F3 - page 12

    CHAPTER 1: INTRODUCTION 1-4 FOT-F3 USER’S MANUAL A fiber optic cable is connected to the transceiver through ST fiber optic ports on the FOT-F3. This provides an optical link to connect the device to the network. 1.3.2 Distance and Cable T ype The FOT-F3 supports single mode fiber optic cable for sizes such as 8.3/125 µ m, 8.7/125 µ m, 9/125 µ ...

  • Cabletron Systems EPIM F3 - page 13

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-5 The SQE test signal is generated after the FOT-F3 has transmitted a data packet. This signal is generated only between the FOT-F3 and the device; it is not transmitted onto the network. Note: Do not enable the SQE test feature when the FOT-F3 is attached to a repeater or Ethernet Version 1 equipment ...

  • Cabletron Systems EPIM F3 - page 14

    CHAPTER 1: INTRODUCTION 1-6 FOT-F3 USER’S MANUAL PWR (Power) When on, this green LED indicates that the FOT-F3 is receiving power. SQE (Signal Quality Error) Test Function When on, this yellow LED indicates that SQE is enabled. XMT (Transmit) This green LED flashes to indicate that the FOT-F3 is transmitting frames onto the network. RCV (Receive) ...

  • Cabletron Systems EPIM F3 - page 15

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-7 1.3.4 Application The FOT-F3 can be configured into your network in many ways. For example, in Figure 1-3, a fiber optic link segment (4) is attached to a Cabletron Systems Multi Media Access Center (MMAC) (5) with a FOMIM-32/36/38. The MMAC serves as an intelligent repeater hub that links the fiber ...

  • Cabletron Systems EPIM F3 - page 16

    CHAPTER 1: INTRODUCTION 1-8 FOT-F3 USER’S MANUAL In another example, shown in Figure 1-4, a FOT-F3 (3) is connected to an MMAC (1) by an AUI cable (2) attached to an Intelligent Repeater Module (IRM) in the MMAC. A lengthy fiber optic link segment (4) of up to five kilometers runs from the FOT-F3 (3) to another FOT-F3 (5). The hardware connection ...

  • Cabletron Systems EPIM F3 - page 17

    GETTING HELP FOT-F3 USER’S MANUAL 1-9 1.4 GETTING HELP If you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact Cabletron Systems Technical Support: By phone (603) 332-9400 Monday – Friday; 8 A.M . – 8 P.M . Eastern Time By CompuServe GO CTRON from any ! prom ...

  • Cabletron Systems EPIM F3 - page 18

    CHAPTER 1: INTRODUCTION 1-10 FOT-F3 USER’S MANUAL • The device history (i.e., have you returned the device before, is this a recurring problem, etc.) • Any previous Return Material Authorization (RMA) numbers 1.5 RELATED MANUALS Use the manuals identified below to supplement the procedures and other technical data provided in this manual. The ...

  • Cabletron Systems EPIM F3 - page 19

    FOT-F3 USER’S MANUAL 2-1 CHAPTER 2 INST ALLA TION REQUIREMENTS Before installing the FOT-F3 Fiber Optic Transceiver, all conditions, guidelines, specifications, and requirements included in this chapter and Appendix A must be met to ensure satisfactory performance from the FOT-F3. Failure to follow these guidelines may result in unsatisfactory ne ...

  • Cabletron Systems EPIM F3 - page 20

    CHAPTER 2: INSTALLATION REQUIREMENTS 2-2 FOT-F3 USER’S MANUAL • When deter mining the maximum fiber optic cab le length, the fiber optic b udget and total network propagation dela y should be calculated and tak en into consideration bef ore fiber r uns are incor porated into any netw or k design. Fiber optic b udget is the combination of the ...

  • Cabletron Systems EPIM F3 - page 21

    FOT-F3 USER’S MANUAL 3-1 CHAPTER 3 INST ALLA TION This chapter contains instructions for unpacking the FOT-F3 Transceiver, connecting the FOT-F3 to an Ethernet device and the network, surface mounting the transceiver (if necessary), and cable support installation. Verify that all the requirements listed in Chapter 2, Installation Requirements , a ...

  • Cabletron Systems EPIM F3 - page 22

    CHAPTER 3: INSTALLATION 3-2 FOT-F3 USER’S MANUAL If you notice any discrepancies, contact Cabletron Systems Technical Support immediately. Refer to Chapter 1, Getting Help , for instructions. 3.2 CONNECTING THE FOT-F3 TO THE NETWORK After you are sure that all the requirements listed in Chapter 2, Installation Requirements , and Appendix A, Speci ...

  • Cabletron Systems EPIM F3 - page 23

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-3 Figure 3-1 SQE Switch 3.2.2 Connecting the A UI Cable To connect your Ethernet device to the FOT-F3, attach an AUI cable as follows. See Figure 3-2. 1. Attach an A UI cab le to the de vice to which the FO T -F3 will be connected. O T -F3 SQE P W R S Q E X M T R C V C L N L N K TX SQE S ...

  • Cabletron Systems EPIM F3 - page 24

    CHAPTER 3: INSTALLATION 3-4 FOT-F3 USER’S MANUAL 2. Attach the f emale connector on the A UI cab le to the A UI por t on the FO T -F3. If the po wer is on f or the Ether net de vice , the PWR LED should be lit, indicating the transceiv er is receiving po wer from the de vice . Also , if the SQE test is enab led, the SQE LED should be lit. Figure ...

  • Cabletron Systems EPIM F3 - page 25

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-5 c. Disconnect the device to which the transceiver is attached. d. Check the AUI connections for proper pinouts. The pinouts for the transceiver connection are listed in Appendix A. e. Check the cable for continuity. f. Reconnect the AUI cable to the FOT-F3 and the device. 3. Mo v e the ...

  • Cabletron Systems EPIM F3 - page 26

    CHAPTER 3: INSTALLATION 3-6 FOT-F3 USER’S MANUAL ST connectors attach to ST ports much like BNC connectors attach to BNC ports. See Figure 3-3. The connector is inserted into the port with an alignment key on the connector inserted into the alignment slot on the port. The connector is then turned to lock it down. Caution: Do not touch the ends of ...

  • Cabletron Systems EPIM F3 - page 27

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-7 Figure 3-3 ST Connectors 6. Chec k that the LNK LED on the FO T -F3 is on. If the LED is off , perf or m each of the f ollowing steps until the LED is on: a. Check that the power is on for the device at the other end of the link. b. Verify that the fiber strands are properly connected ...

  • Cabletron Systems EPIM F3 - page 28

    CHAPTER 3: INSTALLATION 3-8 FOT-F3 USER’S MANUAL If a link is not established, contact Cabletron Systems Technical Support. Refer to Chapter 1, Getting Help , for instructions. 3.3 SURFACE MOUNTING THE FOT-F3 Using the contents of the accessory package, you can mount the FOT-F3 on a surface close to the workstation or on the workstation itself. T ...

  • Cabletron Systems EPIM F3 - page 29

    CABLE SUPPORT INSTALLATION FOT-F3 USER’S MANUAL 3-9 3.4 CABLE SUPPORT INSTALLATION Relieve the strain from the cables attached to the FOT-F3, whether or not the transceiver is mounted to a surface such as a wall. Note: Be sure each cable is securely attached to its port and that the slide latch on the AUI connector is secured to the lock posts on ...

  • Cabletron Systems EPIM F3 - page 30

    CHAPTER 3: INSTALLATION 3-10 FOT-F3 USER’S MANUAL Figure 3-4 Surface Mounting the FOT-F3 3.4.2 Cable Strain Relief f or Non-Mounted FO T -F3 To relieve the strain to cables connected to a FOT-F3 that is not surface mounted, proceed as follows: 1. If possib le, use long tie wr aps to secure the FO T -F3 to a str uctural suppor t such as a beam or ...

  • Cabletron Systems EPIM F3 - page 31

    CABLE SUPPORT INSTALLATION FOT-F3 USER’S MANUAL 3-11 The FOT-F3 is now ready for operation. We recommend that you test the system prior to transmitting data. Refer to Chapter 4, Testing And Troubleshooting , for information about how to test the system. ...

  • Cabletron Systems EPIM F3 - page 32

    CHAPTER 3: INSTALLATION 3-12 FOT-F3 USER’S MANUAL ...

  • Cabletron Systems EPIM F3 - page 33

    FOT-F3 USER’S MANUAL 4-1 CHAPTER 4 TESTING AND TR OUBLESHOO TING This chapter lists procedures to test the FOT-F3 after it is connected to the network. A description of LANVIEW and its function in troubleshooting physical layer network problems is also provided. 4.1 INSTALLATION CHECK-OUT This section contains procedures to test the following • ...

  • Cabletron Systems EPIM F3 - page 34

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-2 FOT-F3 USER’S MANUAL 4. F ollo wing the instr uctions f or the test set, test the jumpers to get a ref erence le v el. Mak e a note of this reading. 5. Disconnect the jumpers from the barrel connector . 6. Using the jumper , attach the optical po wer meter to one end of one strand of the link segment. 7. ...

  • Cabletron Systems EPIM F3 - page 35

    INSTALLATION CHECK-OUT FOT-F3 USER’S MANUAL 4-3 4.1.2 T esting the FO T -F3 Fiber Optic T ransceiver T w o Ether net node testers capab le of generating v alid data pac kets , such as the LAN-MD , are required f or this procedure. Refer to Figure 4-1 and proceed as follows: 1. Using an AUI cable (2), connect a LAN-MD (1) to the FOT-F3 (3). Figure ...

  • Cabletron Systems EPIM F3 - page 36

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-4 FOT-F3 USER’S MANUAL 2. Using another A UI cab le (6), connect the other LAN-MD (7) to another FO T -F3 (5) attached to the same fiber optic link segment as the FO T -F3. 3. Select and r un test 6 - SER VER on the LAN-MD connected in step 1. V er ify that this test passes . • The status on the LAN-MD ...

  • Cabletron Systems EPIM F3 - page 37

    USING LANVIEW FOT-F3 USER’S MANUAL 4-5 Figure 4-2 shows the location of the LANVIEW LEDs on the FOT-F3. This is followed by a description of how to interpret the indications of these LANVIEW LEDs. Figure 4-2 LANVIEW LEDs Optical Link OK (LNK) LED When on, this green LED indicates that a link has been established between the receive circuitry of t ...

  • Cabletron Systems EPIM F3 - page 38

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-6 FOT-F3 USER’S MANUAL Receive (RCV) LED This yellow LED flashes to indicate that the transceiver is receiving a frame from the network. The flash of the LED is pulse stretched for easy viewing. The LED flashes when traffic is on the network, even if the data is not intended for the device attached to the ...

  • Cabletron Systems EPIM F3 - page 39

    USING LANVIEW FOT-F3 USER’S MANUAL 4-7 Power (PWR) LED When on, this green LED indicates that the transceiver is receiving power from the device connected to the FOT-F3 AUI port. If this LED is off, power is not being received from the device or the DC-to-DC converter in the transceiver has failed. ...

  • Cabletron Systems EPIM F3 - page 40

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-8 FOT-F3 USER’S MANUAL ...

  • Cabletron Systems EPIM F3 - page 41

    FOT-F3 USER’S MANUAL A-1 APPENDIX A SPECIFICA TIONS This appendix contains the operational specifications for the FOT-F3. A.1 FIBER OPTIC INTERFACE The FOT-F3 has ST fiber optic ports. Table A-1 lists the parameters along with the associated typical, and minimum/ maximum specifications. Table A-1 Fiber Optic Interface Specifications Parameter Typ ...

  • Cabletron Systems EPIM F3 - page 42

    APPENDIX A: SPECIFICATIONS A-2 FOT-F3 USER’S MANUAL Parameter Typical Minimum Maximum Receive Sensitivity: -31.0 dBm -36.0 dBm -30.0 dBm Max. Receive Input Power: — — -14.0 dBm Transmitter Power at 25 ° C Into 8.3/125 µ m fiber: -18.0 dBm -21.0 dBm -15.0 dBm Output Power Coefficient: -0.07 dB/ ° C— — Notes: Transmitter Power decreases ...

  • Cabletron Systems EPIM F3 - page 43

    AUI CONNECTOR FOT-F3 USER’S MANUAL A-3 A.2 AUI CONNECTOR The AUI connector is a male DB15 receptacle with a metal shell for cable shielding. Refer to Figure A-1 for pinout identification. Figure A-1 AUI Connector Pinout Identification A.3 POWER SUPPLY Table A-2 provides the specifications of the power supply in the FOT-F3. Table A-2 Power Supply ...

  • Cabletron Systems EPIM F3 - page 44

    APPENDIX A: SPECIFICATIONS A-4 FOT-F3 USER’S MANUAL A.4 ENVIRONMENTAL Table A-3 provides the FOT-F3 environmental specifications. A.5 AGENCY APPROVALS Safety The FOT-F3 meets the safety requirements of UL1950, CSA C22.2 No. 950, EN 60950, and 73/23/EEC. Electromagnetic Compatibility The FOT-F3 meets the EMC requirements of FCC Part 15 Class A, EN ...

メーカー Cabletron Systems カテゴリー Network Card

Cabletron Systems EPIM F3のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- EPIM F3の取扱説明書
- Cabletron Systemsの製品カード
- パンフレット
- またはCabletron Systems EPIM F3の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cabletron Systems EPIM F3の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cabletron Systems EPIM F3の取り付け説明書、サービスマニュアル、簡易説明書、またはCabletron Systems EPIM F3のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cabletron Systems EPIM F3の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cabletron Systems EPIM F3デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCabletron Systems EPIM F3を使用するのを助ける技術的文書のことです。説明書は通常、全てのCabletron Systems EPIM F3ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cabletron Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cabletron Systems EPIM F3の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCabletron Systems EPIM F3の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cabletron Systems EPIM F3に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cabletron Systems EPIM F3デバイスの基本機能を使うにあたってのヒント。 Cabletron Systems EPIM F3のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cabletron Systems EPIM F3に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCabletron Systems EPIM F3のメーカー/サービスへの連絡先に関する情報。

Cabletron Systems EPIM F3についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCabletron Systems EPIM F3の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCabletron Systems EPIM F3で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)