Grizzly G7945の取扱説明書

28ページ 1.53 mb
ダウンロード

ページに移動 of 28

Summary
  • Grizzly G7945 - page 1

    RADIAL DRILL PRESS MODEL G7945/46 INSTRUCTION MANUAL COPYRIGHT © 2001 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. JUNE, 2001 PRINTED IN CHINA. ...

  • Grizzly G7945 - page 2

    WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr ...

  • Grizzly G7945 - page 3

    G7945/46 Radial Drill Press -1- Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR ALL TOOLS ......................................................................2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR G7945/46 ......................................4 2. CIRCUIT REQUIREMENTS 110V OPERATION ............................................................. ...

  • Grizzly G7945 - page 4

    -2- G7945/46 Radial Drill Press Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. DO NOT FORCE TOOL. It will do the job better and safer at the ...

  • Grizzly G7945 - page 5

    G7945/46 Radial Drill Press -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your ...

  • Grizzly G7945 - page 6

    -4- G7945/46 Radial Drill Press 1. ALWAYS OPERATE YOUR DRILL PRESS AT SPEEDS that are appropriate for the drill bit size and the material that you are drilling. 2. FEED THE DRILL BIT EVENLY INTO THE WORKPIECE. Back the bit out of deep holes and clear the chips with a brush after you have turned the machine off. 3. MAKE SURE THE DRILL BIT YOU ARE US ...

  • Grizzly G7945 - page 7

    G7945/46 Radial Drill Press -5- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 10-amp fuse or circuit breaker should be used when fusing this drill press. Circuits breakers rated any higher may not be adequate to protect the circuit from power surges. If you find it necessary to use an extension cord with the Model G7945/7946, make sure the cord ...

  • Grizzly G7945 - page 8

    -6- G7945/46 Radial Drill Press SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G7945/46 Radial Drill Press. The Model G7945/46 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Gr ...

  • Grizzly G7945 - page 9

    G7945/46 Radial Drill Press -7- If moving this machine up or down stairs, the machine must be dis- mantled and moved in smaller pieces. Make sure floor and stair structures are capable of supporting the com- bined weight of the machine parts and the people moving them. The Model G7945/46 is shipped from the manu- facturer in a carefully packed cart ...

  • Grizzly G7945 - page 10

    -8- Clean Up The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Always follow the usage ins ...

  • Grizzly G7945 - page 11

    G7945/46 Radial Drill Press -9- SECTION 4: ASSEMBLY Beginning Assembly Most of your Model G7945/46 Radial Drill Press has been assembled at the factory, but some parts must be assembled or installed after deliv- ery. We have organized the assembly process into steps. Please follow along in the order pre- sented here. TOOLS REQUIRED: 11 ⁄ 16 " ...

  • Grizzly G7945 - page 12

    -10- G7945/46 Radial Drill Press The Model G7945 comes with a one piece square table and support as shown in Figure 4 . The Model G7946 comes with a round table and two piece hinged table support. 1. Insert the pinion gear into the hole on the side of the bracket from the inside, starting with the shaft. See Figure 5 . Align the setscrew in the cra ...

  • Grizzly G7945 - page 13

    G7945/46 Radial Drill Press -11- The headstock repre- sents a heavy load. Seek assistance before begin- ning this step. Figure 8 . Lock Handles and gib location. 1. Make sure the locking gib is in the recessed pocket on the inside edge of the headstock opening. See Figure 8. 2. With the help of an assistant, lift the headstock over the top end of t ...

  • Grizzly G7945 - page 14

    -12- G7945/46 Radial Drill Press SECTION 5: ADJUSTMENTS Unplug the drill press before changing speeds. The drill press has 5 speeds ranging from 550 to 3470 R.P.M. There is a speed chart located under the belt guard. Refer to this chart when setting a speed. 1. Loosen the belt tension lock knob on the side of the headstock. See Figure 10 . 2. Pivot ...

  • Grizzly G7945 - page 15

    G7945/46 Radial Drill Press -13- Your radial drill press comes with a depth stop for use when drilling. Follow the instructions below for use. 1. Loosen the depth collar lock knob. See Figure 11 . 2. Secure the wood stock you will be drilling onto the drill press table. 3. With the desired bit installed, lower the spin- dle until the tip of the bit ...

  • Grizzly G7945 - page 16

    -14- G7945/46 Radial Drill Press The Model G7945 table can be adjusted for height and angle. The G7946 adds the adjust- ments of table distance from column and rotation. Follow these instructions to adjust height: 1. Loosen the table support bracket lock han- dle. Turn the table hand crank to lift or lower the table. 2. Remember to lock the support ...

  • Grizzly G7945 - page 17

    G7945/46 Radial Drill Press -15- Head Adjustments Figure 16. Guide pin location. The headstock can be tilted from 45° clockwise to 90° counterclockwise. 1. Loosen the lock handle on the right side of the headstock. 2. Pull out the guide pin located on the left side of the headstock and rotate the pin 90°. See Figure 16 . Tilt the headstock to th ...

  • Grizzly G7945 - page 18

    -16- G7945/46 Radial Drill Press SECTION 6: OPERATIONS Test Run Drill Bit Changes Care must be taken to secure the bit firmly in place. When changing bits, proceed as follows: 1. Disconnect the machine from the power source. 2. Open the chuck wide enough to accept a new bit. 3. Install the bit so the chuck jaws will grab as much of the bit shank as ...

  • Grizzly G7945 - page 19

    G7945/46 Radial Drill Press -17- SECTION 7: MAINTENANCE Lubrication V-Belt Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them. Inspect regularly for tension and wear. Check pul- leys to ensure that they are properly aligned. See pulley/V-belt sections for proper ...

  • Grizzly G7945 - page 20

    -18- G7945/46 Radial Drill Press The following pages contain general machine data, parts diagrams/lists, a troubleshooting guide and Warranty/Return information for your Model G7945/46 Radial Drill Press. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Ou ...

  • Grizzly G7945 - page 21

    G7945/46 Radial Drill Press -19- Design Type ....................................................................................................Bench Model Overall Dimensions: Table ................................................................................................................8 5 ⁄ 8 '' x 9'' Overall Height . ...

  • Grizzly G7945 - page 22

    -20- G7945/46 Radial Drill Press Design Type ......................................................................................................Floor Model Overall Dimensions: Table ........................................................................................................12 3 ⁄ 16 '' Round Overall Height ............... ...

  • Grizzly G7945 - page 23

    43 47 39 37 55 51 50 57 44 48 58 45 59 75 60 32 31 56 46 1 2 3 4 27 34 36 28 28A 28 29 42 41 5 40 33 20 64 65 66 54 38 53 22 23 67 68 16 15 36 71 73 74 69 7 19 11 13 56 49 76 70 17 18 53 21 26 62 25 35 52 72 24 63 2A 11 24 10 77 81 19A 11 83 84 78 79 9 30 8 82 80 4A 5A 84A G7946 ONLY 85 86 ...

  • Grizzly G7945 - page 24

    -22- G7945/46 Radial Drill Press Ref# Part# Description 001 P7945001 BASE 002 P7945002 FLANGE 002A P7946002A W1670 FLANGE 003 PB07 HEX BOLT 5 ⁄ 16 "-18X 3 ⁄ 4 " 004 P7945004 RACK 004A P7945004A LONG RACK 005 P7945005 VERT. COLUMN 005A P7945005A LONG VERT. COLUMN 007 P7945007 TABLE SUPPORT BRACKET 008 P7945008 GEAR 009 P7945009 RETAINE ...

  • Grizzly G7945 - page 25

    G7945/46 Radial Drill Press -23- NOTES ...

  • Grizzly G7945 - page 26

    -24- G7945/46 Radial Drill Press Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole writ ...

  • Grizzly G7945 - page 27

    G7945/46 Radial Drill Press -25- 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt Sander ...

  • Grizzly G7945 - page 28

    FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend: ...

メーカー Grizzly カテゴリー Drill

Grizzly G7945のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- G7945の取扱説明書
- Grizzlyの製品カード
- パンフレット
- またはGrizzly G7945の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Grizzly G7945の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Grizzly G7945の取り付け説明書、サービスマニュアル、簡易説明書、またはGrizzly G7945のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Grizzly G7945の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Grizzly G7945デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがGrizzly G7945を使用するのを助ける技術的文書のことです。説明書は通常、全てのGrizzly G7945ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Grizzlyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Grizzly G7945の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははGrizzly G7945の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Grizzly G7945に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Grizzly G7945デバイスの基本機能を使うにあたってのヒント。 Grizzly G7945のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Grizzly G7945に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるGrizzly G7945のメーカー/サービスへの連絡先に関する情報。

Grizzly G7945についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもGrizzly G7945の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがGrizzly G7945で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)