-
Quadra-Fire QV32-A - page 1
1 - Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. - What to do if you smell gas • Do not try to light any appliance. • Do not touch any electrical switch. • Do not use any phone in your building. • Immediately call your gas supplier from a neighbor's phone. Follow t ...
-
Quadra-Fire QV32-A - page 2
2 These units MUST use one of the vent systems described in the Installing the Fireplace section of the Installers Guide . NO OTHER vent systems or components MA Y BE USED . This gas fireplace and vent assembly MUST be vented directly to the outside and MUST NEVER be attached to a chimney serving a separate solid fuel burning appliance. Each gas ap ...
-
Quadra-Fire QV32-A - page 3
3 TABLE OF CONTENTS Safety and Warning Information .......................................................... 2 Service Parts Lists .................................................................................. 4 Section 1: Approvals and Codes ........................................................... 8 Appliance Certification ................ ...
-
Quadra-Fire QV32-A - page 4
4 QV32-A (NG , LP) Exploded Parts Diagram / Vue éclatée des pièces * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. Service Parts 4 3 5 2 16 7 1 6 8 Log Set Assembly 15 12 11 10 14 9 13 u ...
-
Quadra-Fire QV32-A - page 5
5 ITEM / PIÈCE STANDING PILOT IGNITION / D’ALLUMAGE PAR VEILLEUSE PA RT NUMBER / N° DE PIÈCE On/Off Rock Switc h / Int erupter a bascule marche/arret 060-5 11 F lex Ball Valve Assembly / Fléchir l'Assemblée de Soupape de Balle 302-320A Pie zo Ignitor / Allumage Piézo 291-513 Burner Tu be / Tu be de br ûl eur 567-301A Burner Orifice NG ...
-
Quadra-Fire QV32-A - page 6
6 9 11 12 13 14 15 QV36-A (NG , LP) Exploded Parts Diagram / (GN, PL) Vue éclatée des pièces * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. Service Parts 7 1 2 3 4 5 16 6 8 Log Set Assembly 10 u ...
-
Quadra-Fire QV32-A - page 7
7 ITEM / PIÈCE STANDING PILOT IGNITION / D’ALLUMAGE PAR VEILLEUSE PA RT NUMBER / N° DE PIÈCE On/Off Rocker Switc h / Int errupteur a bascule marche/arret 060-5 11 F lex Ba ll Valve Assemb ly / F léchir l'Assemblée de So upape de Ba lle 302-320A Pie zo Ignitor / Allumage Piézo 291-513 Burner Tu be / Tu be de br ûl eur 567-301A Burner O ...
-
Quadra-Fire QV32-A - page 8
8 Approvals and Codes NOTE: THESE MODELS ARE UL LISTED TO UL307B, THE S TA NDARD FOR GAS-BURNING HE A TING APPLI- ANCES FOR MANU FACTURED HOMES AND RECRE- A TIONAL VEHICLES. Installation Codes The fireplace installation must conform to local codes. Before installing the fireplace, consult the local building code agency to ensure that you are in com ...
-
Quadra-Fire QV32-A - page 9
9 Getting Started Introducing the Village Collection Gas Fireplaces The Village Collection direct vent gas fireplaces are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. The information contained in this Installers Guide , unless noted otherwise, applies to all models ...
-
Quadra-Fire QV32-A - page 10
10 Figure 1. Diagram of the QV36-A TOP STANDOFFS GAS CONTROLS ELECTRICAL ACCESS GAS ACCESS RATING PL ATE/ LABELS 5 3/8 (138mm) GAS LINE ACCESS 2 1/4 (56mm) 37 3/4 (960mm) 36 (913mm) 41 (1040mm) 22 (560mm) 34 1/2 (876mm) 3 1/2 (90mm) 8 (203mm) 26 7/8 (683mm) 8 5/8 (219mm) VENT COLLARS DIAMETER ELECTRICAL ACCESS 6 5/8 (168mm) VENT COLLARS DIAMETER 8 ...
-
Quadra-Fire QV32-A - page 11
11 Figure 2. Diagram of the Q V -32-A 8 (203mm) 23 3/8 (594mm) 8 5/8 (219mm) VENT COLLARS DIAMETER ELECTRICAL ACCESS 3 1/2 (90mm) 36 (913mm) 31 (788mm) 18 3/8 (468mm) 31 (786mm) 32 1/2 (826mm) 5 3/8 (138mm) GAS LINE ACCESS 2 1/4 (56mm) 8 3/4 (222mm) 16 1/4 (413mm) 6 5/8 (168mm) VENT COLLARS DIAMETER 12 7/8 (327mm) 25 3/4 (653mm) TOP STANDOFFS GAS C ...
-
Quadra-Fire QV32-A - page 12
12 Installing the Fireplace Step 1. Locating the Fireplace The following diagram shows space and clearance require- ments for locating a fireplace within a room. Minimum Clearances from the Fireplace to Combustible Materials Inches mm Glass Front ...................................... 36 ........ 914 Floor .......................................... ...
-
Quadra-Fire QV32-A - page 13
13 Figure 5. Framing Dimensions Framing should be constructed of 2 X 4 lumber or heavie r. WARNING: To ensure proper clearances the front framing header must be installed on its narrow edge and to the front of the frame. The framing headers may rest on the fireplace stand-offs. VENT FRAMING HOLE E D Model A B C D E * QV36-A 42” 38 1/4” 16 1/4? ...
-
Quadra-Fire QV32-A - page 14
14 NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) AT EACH JOIN T. Figure 6. D-Series Direct Vent Component Specifications (5-inch inner pipe / 8 5/8-inch outer pipe) DV-36D 5 3/4” (146mm) 8 3/4” (222mm) 11 3/4” (298mm) DV-48D 7 3/8” (187mm) 6 5/32” (156mm) 11 5/8” (295mm) 8 5/8” (220mm) 8 1/2” (216mm) 6 7/16” (164mm) 11 1/16” (281mm ...
-
Quadra-Fire QV32-A - page 15
15 NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93mm) AT EACH JOIN T. Figure 7 . SL D- Series Direct Vent Component Specifications (4-inch inner pipe / 6 5/8-inch outer pipe) 120” (3048mm) 24” (610mm) 36” (914mm) 60” (1524mm) 9 1/4 6 5/8 6 1/2 6 3/8 6 1/2 9 5/8 9 5/8 6 5/8 6 3/8 8 3/4 SL-09D 12-17 SL-12/17D (SL12-17D) SL-24D SL-36D SL-48D 47 3/4 35 ...
-
Quadra-Fire QV32-A - page 16
16 ! Figure 8. Vent System Components and Termination Kits Step 3. Installing the Vent System A. Vent System Approvals These models have vent starting collars on both the top and the back of the unit. Depending upon the installation, decide which ONE set of starting collars will be used to attach the vent system. The starting collar sealing cap mus ...
-
Quadra-Fire QV32-A - page 17
17 STRAIGHT UP VERTICAL VENTING V (FT .) 45' MAX. (13.7 m) Figure 10. Straight up Vertical Venting Use SL D-Series components onl y. NOTE: For vertical venting over 20 feet a restrictor plate is recommended for improved flame appearance. STRAIGHT OUT HORIZON TAL VENTING H Max. Run 36" (914 mm) Use D-Series components onl y. Figure 11. Str ...
-
Quadra-Fire QV32-A - page 18
18 V H 1' MIN. (305mm) 2' MAX. (610mm) 2' MIN. (610mm) 4' MAX. (1.22m) 3' MIN. (914mm) 6' MAX. (1.86m) 4' MIN. (1.22m) 8' MAX. (2.4m) V+H=40' MAX. (12.4m) H = 8' MAX. (2.4m) Figure 12. Venting with One 90° Elbow Use D-Series components onl y. V H Figure 13. Venting with One 90° Elbow V (MIN.) 90 o ...
-
Quadra-Fire QV32-A - page 19
19 V H H + H 1 1' MIN. (305 mm) 2' MAX. (610 mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22 m) 8' MAX. (2.4m) 3' MIN. (914 mm) 6' MAX. (1.86 m) 12' MAX. (3.6m) 4' MIN. (1.22 m) 8' MAX. (2.48 m) 16' MAX. (4.8m) V+H+H 1 = 40' MAX. (12.4 m) H = 8' MAX. (2.48 m) H+H 1 = 16' ...
-
Quadra-Fire QV32-A - page 20
20 Figure 15. Venting with Two 90° Elbows Use SL D-Series components onl y. VENTING WITH TWO (2) 90 o ELBOWS NA TURAL GAS H + H 1 MAX. = 16 FT (4.8m) V + H + H 1 MAX. = 40 FT (12.2m) H + H 1 (MAX.) 2 FT (610mm) 3 FT (914mm) 4 FT (1.22m) 6 FT (1.86m) 8 FT (2.48m) 16 FT (4.8m) VENTING WITH TWO (2) 90 o ELBOWS PROP ANE H + H 1 MAX. = 16 FT (4.8m) V + ...
-
Quadra-Fire QV32-A - page 21
21 Figure 16. Venting with Two 90° Elbows Use SL D-Series components onl y. VENTING WITH TWO (2) 90 o ELBOWS NA TURAL GAS H MAX. = 16 FT (4.8m) V + V 1 + H MAX. = 40 FT (12.2m) H (MAX.) 2 FT (610mm) 3 FT (914mm) 4 FT (1.22m) 6 FT (1.86m) 8 FT (2.48m) 16 FT (4.8m) VENTING WITH TWO (2) 90 o ELBOWS PROP ANE H MAX. = 16 FT (4.8m) V + V 1 + H MAX. = 40 ...
-
Quadra-Fire QV32-A - page 22
22 Figure 17. Venting with Three 90° elbows 1' MIN. (305 mm) 2' MAX. (610mm) 4' MAX. (1.22m) 2' MIN. (610 mm) 4' MAX. (1.22m) 8' MAX. (2.48m) 3' MIN. (914 mm) 6' MAX. (1.86m) 12' MAX. (3.72m) 4' MIN. (1.22 m) 8' MAX. (2.48m) 16' MAX. (4.8m) V 1 +V+H+H 1 = 40' MAX. (12.4m) H = 8' ...
-
Quadra-Fire QV32-A - page 23
23 Figure 18. Venting with three 90° elbows Use SL D-Series components onl y. VENTING WITH THREE (3) 90 o ELBOWS NA TURAL GAS VENTING WITH THREE (3) 90 o ELBOWS PROP ANE V + H + V 1 + H 1 MAX. = 40 FT (12.2m) V + H + V 1 + H 1 MAX. = 40 FT (12.2m) V (MIN.) H (MAX.) H + H 1 (MAX.) 90 o Elbow on T op 2 FT (610mm) 4 FT (1.22m) 1 FT (305mm) 3 FT (914m ...
-
Quadra-Fire QV32-A - page 24
24 Use SL D-Series components onl y. VENTING WITH THREE (3) 90 o ELBOWS NA TURAL GAS H + H 1 MAX. = 16 FT (4.8m) V + V 1 + H + H 1 MAX. = 40 FT (12.2m) MODEL QV36-A H + H 1 (MAX.) 2 FT (610mm) 3 FT (914mm) 4 FT (1.22m) 6 FT (1.86m) 8 FT (2.48m) 16 FT (4.8m) VENTING WITH THREE (3) 90 o ELBOWS PROP ANE H + H 1 MAX. = 16 FT (4.8m) V + V 1 + H + H 1 MA ...
-
Quadra-Fire QV32-A - page 25
25 Figure 20. Venting with Four 90° elbows VENTING WITH FOUR (4) 90° ELBOWS NA TURAL AND PROP ANE GAS V (MIN.) H (MAX.) 2' (609mm) 5' (1.52m) V 1 (MIN.) H 1 (MAX.) V 2 (MIN.) 5' (1.52m) 5' (1.52m) 4.5' (1.37m) V + V 1 + V 2 + H + H 1 MAX. = 40' (12.2m) V H V 2 V 1 H 1 Note: There MUST be a 25% reduction in total H wh ...
-
Quadra-Fire QV32-A - page 26
26 ! STARTING COLLAR STOVE SEALANT BEAD 1 INCH (25.4mm) FIRST VENT COMPONENT If the installation is for a termination cap attached directly to the fireplace, skip to the sections, Install Firestops and Vent Termination . 3/8” (9.5mm) Venting Out the Rear Vent (See Figure 21) Remove the installed rear seal cap from the rear starting collars by cut ...
-
Quadra-Fire QV32-A - page 27
27 For Vertical Runs - The vent system must be supported every eight (8) feet (2.4m) above the fireplace flue outlet by wall brackets. To install support brackets for vertical runs: • Attach wall brackets to the vent pipe and secure the wall bracket to the framing members with nails or screws. • Position the firestops on both sides of the hole ...
-
Quadra-Fire QV32-A - page 28
28 For Vertical Runs - One ceiling firestop is REQUIRED at the hole in each ceiling through which the vent passes. To install firestops for vertical runs that pass through ceilings: • Position a plumb bob directly over the center of the verti- cal vent component. • Mark the ceiling to establish the centerpoint of the vent. • Drill a hole or d ...
-
Quadra-Fire QV32-A - page 29
29 ! C. Vent Termination For Horizontal Terminations - To attach and secure the termination to the last section of horizontal vent: • Rotate and interlock the ends as described at the begin- ning of the Installing Vent Components section. • The termination kit should pass through the wall firestops from the exterior of the building. • Adjust ...
-
Quadra-Fire QV32-A - page 30
30 ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ V = VENT TERMINAL X = AIR SUPP LY INLET = AREA WHERE TERMINAL I ...
-
Quadra-Fire QV32-A - page 31
31 For Vertical Terminations - To locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint. • Make the outline of the roof hole around the centerpoint nail. • The size of the roof hole framing dimensions depend on the pitch of the roof. There M ...
-
Quadra-Fire QV32-A - page 32
32 Step 4. Positioning, Leveling, and Securing the Fireplace • Place the fireplace into position. • Level the fireplace from side to side and from front to back. • Shim the fireplace with non-combustible material, such as sheet metal, as necessar y. • Secure the fireplace to the framing using nails or screws through the nailing tabs. ! ! Th ...
-
Quadra-Fire QV32-A - page 33
33 Figure 35. Gas Supply Line • Insert insulation from the outside of the fireplace and pack the insulation tightly to totally seal between the pipe and the outer casing. • At the gas line access hole the gap between the supply piping and gas access hole can be plugged with non- combustible insulation to prevent cold air infiltration. Step 6. T ...
-
Quadra-Fire QV32-A - page 34
34 Step 8. Wiring the Fireplace NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF AB- SENT FOR EXTENDED TIME PERIODS. THIS WILL PRE- VENT ACCIDENT AL FIREPLACE OPERA TION. For Standing Pilot Ignition Wiring Appliance Requirements • This appliance DOES NOT require 110-120 VAC to operate. WA ...
-
Quadra-Fire QV32-A - page 35
35 Step 9. Finishing Figure 38 shows the minimum vertical and corresponding maximum horizontal dimensions of fireplace mantels or other combustible projections above the top front edge of the fireplace. See Figures 3 and 4 for other fireplace clearances. Only non-combustible materials may be used to cover the black fireplace front. W ARNING: WHEN F ...
-
Quadra-Fire QV32-A - page 36
36 Installing the Trim Combustible materials may be brought up to the specified clearances on the side and top front edges of the fireplace, but MUST NEVER overlap onto the front face. The joints between the finished wall and the fireplace top and sides can only be sealed with a 300° F . (149° C) minimum sealant. WA RNING: WHEN FINISHING THE FIRE ...
-
Quadra-Fire QV32-A - page 37
37 Step 11. Before Lighting the Fireplace Before lighting the fireplace, be sure to do the following: Remove all paperwork from underneath the fireplace. Review safety warnings and cautions • Read the Safety and Warning Information section at the beginning of this Installers Guide . Double-check for gas leaks • Before lighting the fireplace, do ...
-
Quadra-Fire QV32-A - page 38
38 Step 12. Lighting the Appliance STANDING PILOT IGNITION A. This appliance (standing pilot version) has a pilot that must be lighted by hand. When lighting the pilot, follow these instructions exactl y. B. BEFORE LIGHTING smell all around the appli- ance area for gas. Be sure to smell next to the floor because some gas is heavier than air and wil ...
-
Quadra-Fire QV32-A - page 39
39 Maintaining and Servicing Your Fireplace Fireplace Maintenance Although the frequency of your fireplace servicing and main- tenance will depend on use and the type of installation, you should have a qualified service technician perform an appli- ance check-up at the beginning of each heating season. See the table below for specific guidelines re ...
-
Quadra-Fire QV32-A - page 40
40 Troubleshooting W ith proper installation, operation, and maintenance your gas fireplace will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service person in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by ...
-
Quadra-Fire QV32-A - page 41
41 Symptom Possible Cause Corrective Action 3. (Co nt inued) f. H ig h l imit switc h is defecti ve or has reached its ma x im um temperature. A llow the un i t to cool. I f the burner remains lit after the fireplace warms up, the sw i tch is good. 4. Frequent pilot outage problem. a. Pilot flame ma y be too high or too lo w , or blowi ng (high), c ...
-
Quadra-Fire QV32-A - page 42
42 The Aladdin Hearth Products limited Lifetime Warranty guarantees that the following components will work as de- signed for the lifetime of the stove or Aladdin Hearth Products will repair or replace them. These items include, but are not limited to, steel and cast iron components, all gas burners, gas logs, combustion chambers, heat exchanger sy ...
Quadra-Fire QV32-Aについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもQuadra-Fire QV32-Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQuadra-Fire QV32-Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。