-
Sangean Electronics ATS-505P - page 1
...
-
Sangean Electronics ATS-505P - page 2
...
-
Sangean Electronics ATS-505P - page 3
Control Locations Power/Sleep Power On/off/Alarm off/sleep function Display Switch between radio frequency and time while radio is power on Mode Mode set up (please see below mode button set up) Radio alarm Buzzer alarm Tuning Up/Down Enter command button for frequency and time set Selection cancel Numbered buttons and memory scan (the 0 Button) Me ...
-
Sangean Electronics ATS-505P - page 4
1.Position the radio face down 2.Press the catch marked " " and slide in the direction shown. 3.Insert the 4 UM-2 (LR6)(AA size) batteries. 4. Replace the battery cover. Choosing a power supply Installing batteries Battery replacement Low battery warnings Using the AC adapter Setting the clock This radio can be operated using. 4 Alkaline ...
-
Sangean Electronics ATS-505P - page 5
The real time can be set. 1. When the radio is switched off 2. If the radio switched on, press DISPLA Y button to time status. 3. Press "ENTER" button for more than 2 seconds until " " real time symbol and 4. Set the correct time by pressing the numbered buttons. As you press each button, the corresponding number will show on th ...
-
Sangean Electronics ATS-505P - page 6
5 Waveband selection Direct tuning Manual tuning by tuning UP/DOWN button There are four waveband selection by pressing BAND button Waveband Frequency coverage Aerial Type -------------------------------------------------------------------------------------------- FM 87.50- 108 MHz Telescopic Full extend the aerial, angle and rotate for best recept ...
-
Sangean Electronics ATS-505P - page 7
6 Note: Each press of Up or Down button will change the frequency in increment of FM: 100kHz or 200kHz depending on the versions. MW: 9kHz or 10kHz depending on the versions. SW: 5kHz LW : 9kHz Rotary tuning is accomplished using the convenient Rotary Tuning Knob. Original tuning step is as below but can be changed by the MODE button as described l ...
-
Sangean Electronics ATS-505P - page 8
3.Press the button marked M (memory), display M and suggested preset number will flash, press ENTER to store your station in that memory position. 4.Preset positions may be exchanged easily. Select preset station that is to be changed, press memory button ( M and existing memory position will flash). select new preset position. Preset will be excha ...
-
Sangean Electronics ATS-505P - page 9
3.Press T uning UP and DOWN button at the same time for more than 2 seconds. The radio will beep and then scan from the lowest frequency on the selected band. Automatically storing stations in preset memory based on signal strength. 4.After APS is completed, a beep will be heard. The display will show M1 and the strongest station for your area. 5.I ...
-
Sangean Electronics ATS-505P - page 10
Note: 1.When alarm is on, press POWER button to turn off the alarm for 24 hours. 2.Radio alarm on will last for one hour if not turned off by pushing the POWER button. 3.Turn the radio to the required station before setting the radio alarm. When the alarm is on, the radio will play last station selected. A repeating beep tone will sound when using ...
-
Sangean Electronics ATS-505P - page 11
10 Numbered key 8 key 1 key 1 FM 100kHz FM 200 kHz tuning step tuning step 2. MW 9 kHz MW 10 kHz 3 12 hour format 24 hour format 4 Beep tone off Beep tone on 5 Memory Rearranged Complete with ENTER button For example, if you like to change from MW 10 kHz to 9 kHz, press MODE, numbered button 2 , 0 , then complete with ENTER button. Y ou can rearran ...
-
Sangean Electronics ATS-505P - page 12
FM Mono/Stereo Headphones (or earphones) Lock switch Light DX/Local switch SW EXT . ANT To listen to FM stereo broadcasts, tune to the required station, plug in headphones and set the FM ST./MO. Switch located on the left side of the radio to to FM ST. (stereo) position, If the station being received is weak some hiss may be audible, to reduce the ...
-
Sangean Electronics ATS-505P - page 13
Troubleshooting/RESET button Care and maintenance Specifications If the radio fails to operate correctly, or some digits on the display are missing or incomplete. carry out the following procedure. 1.Switch off the radio and remove the batteries. 2.With the aid of a suitable implement (the end of paper clip or pen), press the RESET button located a ...
-
Sangean Electronics ATS-505P - page 14
Specifications content Power requirement 6V Batteries 4 X IEC size LR6 (AA) (UM-3) Circuit features Semiconductors 1 LSI 7 IC's, 35 transistors, 7 FET , 33 diodes, 3 LED Aerial system AM/L W Built in ferrite aerial SW T elescopic aerial FM T elescopic aerial Output Power 300 mW 10% T.H.D. Sockets Headphones socket 3.5 mm dia. stereo DC in 6 vo ...
Sangean Electronics ATS-505Pについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもSangean Electronics ATS-505Pの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSangean Electronics ATS-505Pで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。