Polycom 4400の取扱説明書

23ページ 0.8 mb
ダウンロード

ページに移動 of 23

Summary
  • Polycom 4400 - page 1

    VIEW Certified Configuration Guide Cisco 4400 Series Wireless LAN Controller (WLC), Wireless Integrated Serv ices Module (WiSM), and 3750G Integrated Wireless LAN Controller with 1100, 1130, 1200, 1230 and 1240 Series APs March 2009 Edition 1725-36070-001 Version P ...

  • Polycom 4400 - page 2

    Con fig ura tio n Gu ide Trademark Information Polycom® and t he logo designs SpectraLink® LinkPlus Link NetLink SVP Are trademarks and registe red trademarks of Polycom, Inc. in the Un ited States of Am erica and various co untries. All other trademark s used herein are the propert y of their respective owners. Patent Information The accompanyin ...

  • Polycom 4400 - page 3

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Introduction Polycom's Voice Interoperability for Enterprise Wireless (VIEW) Certification Program is designed to ensure interoperability and high performance between SpectraLink Wireless Telephones and Wireless LAN infrastructure products. The products listed ...

  • Polycom 4400 - page 4

    Con fig ura tio n Gu ide Known Limitations • Wi-Fi Multimedia ( WMM ) must be disabled in order for SpectraLink Wireless Telephones to work properly. • Heavy multicast, broadcast, or push-to-talk ( PTT ) traffic may impair voice quality. • The Cisco 1000 series APs are not VIEW Certified at this time. • Voice and data must be separated onto ...

  • Polycom 4400 - page 5

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Network Topology The following configuration was tested during VIEW Certification. It is important to note that this configuration is not necessar ily applicable to all customer environments. SpectraLink 8000 Wireless Telephones SpectraLink 8000 SVP Server SpectraLi ...

  • Polycom 4400 - page 6

    Con fig ura tio n Gu ide Configuring a New Controller Starting from Factory Defaults 1. Initial provisioning of the controller is done via the command line interface (CLI). Connect a null modem serial cable between the console port of the controller and the serial port of a PC. 2. Open a terminal program, such as Hyper Terminal, and configure the p ...

  • Polycom 4400 - page 7

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Connecting to the Controller via a Browser 1. Connect to the WLC by pointing your internet browser to the URL: https<IP_Addr> (where <IP_Addr> is the IP address of the management interface of the WLC). 2. Click the Login prompt. The default User Name and ...

  • Polycom 4400 - page 8

    Con fig ura tio n Gu ide Installing Software 1. Make sure that the VIEW Certified version of software is installed on the controller. From the main menu, click Monitor . 2. In the navigation pane, click Summary. The heading labeled Software Version shows the current software version. 3. Download the appropriate software for your model of controller ...

  • Polycom 4400 - page 9

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Controller Setup The initial setup of the controller is shown below. The setup instructions outlined in this document are for the configuration shown in the diagram only. Your configuration may differ, and the appropriate adjustments must be made. It is not necessar ...

  • Polycom 4400 - page 10

    Con fig ura tio n Gu ide Connecting APs As the APs are connected to the ne t work, they should automatically find the controller via the LW APP discovery algorithms. The Dynamic Host Configuration Protocol (DHCP) server will assign each AP an IP address. You can configure a DHCP server to run on a remote PC for a small deployment. However, for larg ...

  • Polycom 4400 - page 11

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 4. Under DHCP Information, enter the IP address of the Primary DHCP Server. 5. Repeat this step for the ap-manager interface. 6. Click the Apply button and save the changes. PN: 1725-36070-001_P.doc 11 ...

  • Polycom 4400 - page 12

    Con fig ura tio n Gu ide AP Configuration 1. Power-on and connect the APs to the network. Wait a few minutes for the APs to find the controller. 2. Verify the APs are associated to the WLC. 3. From the main menu, click Monitor. Configuration for SpectraLink Wireless Telephones running in 802.11b mode 1. From the main menu, click Wireless . 2. In th ...

  • Polycom 4400 - page 13

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 4. Set Admin Status to Enable . 5. Configure any other settings that might be relevant to your deployment as needed. 6. Click the Apply button to save all changes. 7. In the navigation pane under 802.11b/g/n, select Network. 8. Set 802.11b/g Network Status to Disabl ...

  • Polycom 4400 - page 14

    Con fig ura tio n Gu ide require the following minimum dBm reading to support the corresponding Mandatory data rate setting in the access point. 802.11 Radio Standard Minimum Available Signal Strength (RSSI) Maximum “Mandatory ” Data Rate -70 dBm 1 Mb/s 802.11b -60 dBm 11 Mb/s -60 dBm 6 Mb/s 802.11a -45 dBm 54 Mb/s For additional details on RF ...

  • Polycom 4400 - page 15

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 9. Use the default Fragmentation Threshold (2346 bytes). 10. Set the Beacon Period to 100. 11. Set DTIM Peri od to 2 . 12. SpectraLink Wireless Telephones do not support dynamic power and will not utilize the information element that is set when DTPC Support is enab ...

  • Polycom 4400 - page 16

    Con fig ura tio n Gu ide Configuration for SpectraLink Wireless Telephones running in 802.11a mode 1. From the main menu, click Wireless. 2. In the navigation pane, under Access Points sele ct Radios , then select 802.11a /n. All the APs that are connected should be listed, showing their Operational Status as UP . 3. Select Configure from the drop- ...

  • Polycom 4400 - page 17

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 4. Set Admin Status to Enab le . 5. Configure any other settings that might be relevant to your deployment as needed. 6. Click the Apply button to save all changes. 7. In the navigation pane under 802.11a/n, select Network. 8. Set 802.11a Network Status to Disable ; ...

  • Polycom 4400 - page 18

    Con fig ura tio n Gu ide 10. Use the default Fragmentation Threshold (2346 bytes). 11. Set the Beacon Period to 100 . 12. Set DTIM Peri od to 2 . 13. SpectraLink Wireless Telephones do not support dynamic power and will not utilize the information element that is set when DTPC support is enabled. Handset power should be configured to match the high ...

  • Polycom 4400 - page 19

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 15. In the navigation pane under 802.11a/n, select EDCA Parameters. 16. Select Spectralink Voice Priority from the drop-down list. 17. Click the Apply button t o save the settings. 18. In the navigation pane under 802.11a /n, select Network. 19. For 802.11a Net work ...

  • Polycom 4400 - page 20

    Con fig ura tio n Gu ide Setting Up the SSIDs It is required for voice and data to be on separate SSIDs to prioritize voice traffic. The voice SSID must be set to Platinum for Quality of Service (as shown in the screen shot below) and the data SSID must be set to Silver for Quality of Service . Setting up the voice SSID 1. From the main menu, click ...

  • Polycom 4400 - page 21

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs 5. Under the Profile Name heading, s elect the new Voice WLAN Profile. 6. Under the General tab , verify the Radio Policy corresponds to the SpectraLink Wireless Telephone configuration. a. For SpectraLink e340/h340/i640 Wireless Telephones: • The Radio Policy sho ...

  • Polycom 4400 - page 22

    Con fig ura tio n Gu ide 8. Under the Security tab, select the desired security policy (either WPA or WPA2) and enter all required options. 9. Under the QoS tab, set Quality of Service to Platin um (voice ). (Note: This is the required setting for voice traffic.) 10. Set WMM Policy to Disabled. (Note: This is required for usage with SpectraLink Wir ...

  • Polycom 4400 - page 23

    Cisco: 4400 Series WLC, WiSM and 3750G Integrated WLC with 1100 and 1200 Series APs Further Assistance 1. An installation and configuration guide for the 4400 WLC can be found on Cisco’s website: http://www.cisco.com/en/US/docs/wireless/controller/5.0/co nfiguration/guide/ccg50.html 2. To convert the 1200 series autono mous AP to an LWAPP, go to: ...

メーカー Polycom カテゴリー Network Card

Polycom 4400のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 4400の取扱説明書
- Polycomの製品カード
- パンフレット
- またはPolycom 4400の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Polycom 4400の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Polycom 4400の取り付け説明書、サービスマニュアル、簡易説明書、またはPolycom 4400のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Polycom 4400の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Polycom 4400デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPolycom 4400を使用するのを助ける技術的文書のことです。説明書は通常、全てのPolycom 4400ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Polycomの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Polycom 4400の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPolycom 4400の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Polycom 4400に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Polycom 4400デバイスの基本機能を使うにあたってのヒント。 Polycom 4400のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Polycom 4400に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPolycom 4400のメーカー/サービスへの連絡先に関する情報。

Polycom 4400についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPolycom 4400の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPolycom 4400で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)