Cabletron Systems STH-24の取扱説明書

32ページ 0.2 mb
ダウンロード

ページに移動 of 32

Summary
  • Cabletron Systems STH-24 - page 1

    SmartSwitch 9000 9T122-24 User’s Guide 9031206-02 ...

  • Cabletron Systems STH-24 - page 2

    ...

  • Cabletron Systems STH-24 - page 3

    i Notice Notice Cabletron Systems r eserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made. The hardwar e, firmware, or softwar e described in this manual is subject to ...

  • Cabletron Systems STH-24 - page 4

    Notice ii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation. NOTE: This equipment has been tested and found to c ...

  • Cabletron Systems STH-24 - page 5

    iii Notice DECLARA TION OF CONFORMITY ADDENDUM Application of Council Directi ve(s): 89/336/EEC 73/23/EEC Manufacturer’ s Name: Cabletron Systems, Inc. Manufacturer’ s Address: 35 Industrial Way PO Box 5005 Rochester, NH 03867 European Representati ve Name: Mr. J. Solari European Representati ve Address: Cabletron Systems Limited Nexus House, N ...

  • Cabletron Systems STH-24 - page 6

    Notice iv ...

  • Cabletron Systems STH-24 - page 7

    v Contents Chapter 1 Intr oduction Features........................................................................................................................... 1-1 Related Manuals ............................................................................................................ 1-4 Getting Help ..................................... ...

  • Cabletron Systems STH-24 - page 8

    Contents vi ...

  • Cabletron Systems STH-24 - page 9

    1-1 Chapter 1 Intr oduction The 9T122-24 MicroLAN™ Switch Module, shown in Figur e 1-1, is a three port T oken Ring bridge and r outer module. This module supports either one token ring with 24 HUB connections, or two separate T oken Rings with 12 HUB connections, and an interface to the FNB backplane. Features Processor The 9T122-24 is equipped ...

  • Cabletron Systems STH-24 - page 10

    Introduction 1-2 Management Information Base (MIB) Support The 9T122-24 module provides MIB support including: • IETF MIB II (RFC 1213) • IETF RMON MIB (RFC 1271 and 1513) • IETF Bridge MIBs (RFC 1493 and 1525) • IEEE 802.5 T oken Ring MIB (RFC 1231) • Cabletron Enterprise MIBs Ring Security This feature pr events unauthorized stations fr ...

  • Cabletron Systems STH-24 - page 11

    1-3 Introduction Figure 1-1. The 9T122-24 MicroLAN Module 1 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 16 Mb SMB CPU FNB 9T122-24 TOKEN RING ...

  • Cabletron Systems STH-24 - page 12

    Introduction 1-4 Related Manuals The manuals listed below should be used to supplement the procedur es and technical data contained in this manual. SmartSwitch 9000 Installation Guide SmartSwitch 9000 Operations Guide SmartSwitch 9000 9C300-1 Environmental Module User ’s Guide SmartSwitch 9000 9C214-1 AC Power Supply User ’s Guide SmartSwitch 9 ...

  • Cabletron Systems STH-24 - page 13

    2-1 Chapter 2 Installation Installing the Micr oLAN Module The SmartSwitch 9000 MicroLAN Module may be installed into any of the 14 slots that are available. T o install, follow the steps below: 1. Switch off the power supplies and r emove all power from the SmartSwitch 9000 chassis. 2. Remove the blank panels, covering the slots that the module is ...

  • Cabletron Systems STH-24 - page 14

    Installation 2-2 Figure 2-1. Installing the MicroLAN Module Metal Back-Panel Module Guides Module Jack for ESD Wrist Strap Plastic Tab W arning: Ensure that the circuit card is between the card guides. Lock do wn the top and bottom plastic tabs at the same time, applying e ven pressure. ...

  • Cabletron Systems STH-24 - page 15

    2-3 Installation The Reset Switch The Reset switch is located on the front panel, under the top plastic tab as shown in Figure 2-2. It serves two functions: • Pressing the r eset switch twice within three seconds causes the pr ocessor (i960) to reset. • Pressing and holding the switch on for thr ee or more seconds causes the module to shutdown. ...

  • Cabletron Systems STH-24 - page 16

    Installation 2-4 User -Accessible Components Figure 2-3 shows the various components that ar e accessible to the user . These consist of an eight-position dip switch (explained in the next section), replaceable PROMs and sockets for RAM. These will be used for future upgrades. Figure 2-3. User Accessible Components SMB-1 PROM i960 Processor Flash S ...

  • Cabletron Systems STH-24 - page 17

    2-5 Installation Setting the Module Car d DIP Switch An eight-switch DIP switch is located on the module car d as shown in Figure 2-3 and in Figure 2-4. The function of the switches ar e listed in T able 2-1. Figure 2-4. Location of Module DIP Switch 1 2 3 4 5 6 7 8 ...

  • Cabletron Systems STH-24 - page 18

    Installation 2-6 See the Cautions at the end of this table. Ring Speed The module defaults to a 16Mbps ring speed on all rings. This may be changed though local management. T able 2-1. Function of DIP Switch Switch Function Description 8 Clear Password 1 When toggled, this switch clears user-enter ed passwords stor ed in NVRAM, and restor es the de ...

  • Cabletron Systems STH-24 - page 19

    2-7 Installation Multi-Ring Out Capability Any port of the module may be configured as a ring-out port thr ough management software. In this configuration a stand-alone passive concentrator (such as an IBM 8228) may be added to the ring as shown in Figure 2-5. This allows for a star-wir ed network with the SmartSwitch 9000 at the center . Consult ...

  • Cabletron Systems STH-24 - page 20

    Installation 2-8 ...

  • Cabletron Systems STH-24 - page 21

    3-1 Chapter 3 Operation The 9T122-24 MicroLAN Module pr ovides connectivity between the front panel T oken Ring(s) and the FDDI rings on the backplane (FNB-1 or FNB-2). SmartSwitch 9000 modules connect to either the Internal Network Bus (INB) or the Flexible Network Bus (FNB) bus. The 9T122-24 module connects to the FNB bus. Figure 3-1 is a block d ...

  • Cabletron Systems STH-24 - page 22

    Operation 3-2 Bridging The 9T122-24 is configured for SR T bridging. It will pass SR (Source Routing) frames between the rings and provides translation to transpar ent frames over the FNB to Ethernet and FDDI modules. For information on configuring the bridging function, see the addendum to the SmartSwitch 9000 Local Management User ’s Guide, c ...

  • Cabletron Systems STH-24 - page 23

    3-3 Operation Sour ce Route Bridging Source Route Bridging operates by transmitting frames over a designated r oute. Unlike T ransparent Bridging, all devices in a Sour ce Route Bridged (SRB) network “know” the locations of other stations within the network. Using a portion of the MAC frame header known as the RIF (Routing Information Field), t ...

  • Cabletron Systems STH-24 - page 24

    Operation 3-4 Fle xible Netw ork Bus (FNB) The FNB consists of two dual FDDI networks, the FNB-1 and FNB-2, providing up to 400 Mbps of data bandwidth. These FDDI networks are 100% ANSI FDDI-compliant supporting SMT (version 7.3), MAC, PHY , and PMD standards. This allows the FNB to traverse multiple SmartSwitch 9000 hubs, or connect to any ANSI FD ...

  • Cabletron Systems STH-24 - page 25

    3-5 Operation System Diagnostic Contr oller This diagnostic controller is composed of a Z-80 micr oprocessor and its supporting logic. The diagnostic controller is designed to contr ol the power-up sequencing of modules, monitor the 9T122-24 input and output power parameters, keep watch over the main host processor , as well as monitor the temperat ...

  • Cabletron Systems STH-24 - page 26

    Operation 3-6 The i960 core pr ovides the SNMP pr otocol stacks, as well as support for industry- standard MIBs. Additionally , Cabletr on enterprise-extension MIBs are supported for each media type. Advanced management services, such as the Distributed LAN Monitor , RMON, telnet and network address to MAC addr ess mapping, are also pr ovided by th ...

  • Cabletron Systems STH-24 - page 27

    4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs, shown in Figur e 4-1, indicate the status of the module and may be used as an aid in troubleshooting. Figure 4-1. LANVIEW LEDs 1 2 1 2 3 4 5 16 Mb SMB CPU FNB 9T122-24 TOKEN RING SMB CPU FNB 9T122-24 TOKEN RING System Status FNB T ransmit T oken Ring Mac T ransmit T oken Ring Mac Receiv e FNB ...

  • Cabletron Systems STH-24 - page 28

    LANVIEW LEDs 4-2 The functions of the two System Status LEDs, System Management Bus (SMB) and the CPU, are listed in T able 4-1. The functions of the FNB receive LED ar e listed in T able 4-2. The functions of the FNB transmit LED are listed in T able 4-3. T able 4-1. System Status LEDs (SMB and CPU) LED Color State Description Green Functional Ful ...

  • Cabletron Systems STH-24 - page 29

    4-3 LANVIEW LEDs The functions of the T oken Ring Mac r eceive LEDs are listed in T able 4-4. The function of the T oken Ring Mac transmit LEDs ar e listed in T able 4-5. The functions of the Link LED are listed in T able 4-6. T able 4-4. T oken Ring Receive LED LED Color State Red No link, Port disabled Red (Flashing) Link, Port disabled Green Lin ...

  • Cabletron Systems STH-24 - page 30

    LANVIEW LEDs 4-4 The function of the T oken Ring speed LEDs is listed in T able 4-7. T able 4-7. T oken Ring Speed LED Color State Y ellow 16 Mbs Off 4 Mps ...

  • Cabletron Systems STH-24 - page 31

    5-1 Chapter 5 Specifications Safety This equipment meets the safety requir ements of: • UL 1950 • CSA C22.2 No. 950 • EN 60950 • IEC 950 • EMI Requirements of FCC Part 15 Class A • EN 55022 Class A • VCCI Class I • EMC requir ements of: EN 50082-1 IEC 801-2 ESD IEC 801-3 Radiated susceptibility IEC 801-4 EFT Service MTBF (MHBK-217E ...

  • Cabletron Systems STH-24 - page 32

    Specifications 5-2 Ph ysical Dimensions: 35.0 D x 44.0 H x 3.0 W centimeters (13.8 D x 17.4 H x 1.2 W inches) W eight: Unit: 1.36 kg. (3lb) Shipping: 1.81 kg. (4lb) Electrical CPU: i960 Shared DRAM Memory: 4Mb (expandable to 12 Mb) Local DRAM Memory: 4Mb (expandable to 12 Mb) Flash: 2Mb (expandable to 14 Mb) T oken Ring Interfaces: (2) T exas Inst ...

メーカー Cabletron Systems カテゴリー Switch

Cabletron Systems STH-24のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- STH-24の取扱説明書
- Cabletron Systemsの製品カード
- パンフレット
- またはCabletron Systems STH-24の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cabletron Systems STH-24の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cabletron Systems STH-24の取り付け説明書、サービスマニュアル、簡易説明書、またはCabletron Systems STH-24のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cabletron Systems STH-24の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cabletron Systems STH-24デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCabletron Systems STH-24を使用するのを助ける技術的文書のことです。説明書は通常、全てのCabletron Systems STH-24ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cabletron Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cabletron Systems STH-24の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCabletron Systems STH-24の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cabletron Systems STH-24に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cabletron Systems STH-24デバイスの基本機能を使うにあたってのヒント。 Cabletron Systems STH-24のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cabletron Systems STH-24に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCabletron Systems STH-24のメーカー/サービスへの連絡先に関する情報。

Cabletron Systems STH-24についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもCabletron Systems STH-24の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCabletron Systems STH-24で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)