-
Texas Instruments HPA070 - page 1
User ’s Guide 1 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) User ’ s G uide ...
-
Texas Instruments HPA070 - page 2
2 EVM IMPORT ANT NOTICE T exas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EV ALUA TION PURPOSES ONL Y and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms ...
-
Texas Instruments HPA070 - page 3
3 DYNAMIC W ARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 0 V DC to 14 V DC . Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the i ...
-
Texas Instruments HPA070 - page 4
SLUU186 − March 2004 4 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) Mark D ennis System Pow er Contents 1 Introduction 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Texas Instruments HPA070 - page 5
SLUU186 − March 2004 5 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 3 Schematic + + Figure 1. TPS40055EVM−001 (HP A070) Schematic ...
-
Texas Instruments HPA070 - page 6
SLUU186 − March 2004 6 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 4 Component Selection 4.1 TPS40055 Device Selection Th e TPS4005x family of parts offers a range of output current configurations including source only (TPS40054), source/sink (TPS40055), or source/sink with V OUT prebias (TPS40057). In this converter the TP ...
-
Texas Instruments HPA070 - page 7
SLUU186 − March 2004 7 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 4.3 UVLO Circuitry The user programmable UVLO built into the TPS4005x provides hysteresis for transients shorter than a total count of seven cycles. If the input voltage to the converter can be slowly rising around the minimum V IN range, external hysteresis ...
-
Texas Instruments HPA070 - page 8
SLUU186 − March 2004 8 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 4.6 Output Capacitor Selection Selection of the output capacitor is based on many application variables, including function, cost, size, and availability . The minimum allowable output capacitance is determined by the amount of inductor ripple current and th ...
-
Texas Instruments HPA070 - page 9
SLUU186 − March 2004 9 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 4.8 Short Circuit Protection The TPS40055 implements short circuit protection by comparing the voltage across the topside MOSFET while it is ON to a voltage developed across R LIM due to an internal current source of 10 µ A inside pin 16. Both of these volt ...
-
Texas Instruments HPA070 - page 10
SLUU186 − March 2004 10 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 5 T est Setup Figure 2 illustrates the basic test setup needed to evaluate the TPS40055EVM−001. 5.1 DC Input Source The input voltage source should be capable of supplying between 10 V DC and 14 V DC and rated for at least 4 A of current. For best results ...
-
Texas Instruments HPA070 - page 11
SLUU186 − March 2004 11 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 6 T est Results / Performance Data 6.1 Efficiency and Power Loss Figure 3 shows the efficiency as the load is varied from 1 A to over 15 A. The typical ef ficiency remains over 90% as the load ranges from 3 A to 12 A. Figure 3 0 88 78 2 86 80 90 94 468 1 0 ...
-
Texas Instruments HPA070 - page 12
SLUU186 − March 2004 12 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 6.3 Output Ripple and T ransient Response Figure 6 shows the typical output voltage ripple with I OUT =15 A to be less than 20 mVpp. The transient response is shown in Figure 7 as the load is stepped from 5 A to 15 A. The voltage deviation is less than 60 m ...
-
Texas Instruments HPA070 - page 13
SLUU186 − March 2004 13 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) Figure 9. T op Side Copper Figure 10. Internal Layer 1 Copper ...
-
Texas Instruments HPA070 - page 14
SLUU186 − March 2004 14 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) Figure 1 1. Internal Layer 2 Copper Figure 12. Bottom Layer Copper ...
-
Texas Instruments HPA070 - page 15
SLUU186 − March 2004 15 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 8 List of Materials T able 1 lists the parts values of the evaluation board. These values can be modified to meet the application requirements. T able 1. TPS40055EVM−001 (HP A070) List of Materials REFERENCE DESIGNA TOR QTY DESCRIPTION SIZE MFR P ART NUMB ...
-
Texas Instruments HPA070 - page 16
SLUU186 − March 2004 16 TPS40055-Based Design Converts 12-V Bus to 1.8 V at 15 A (HP A070) 9 References 1. Data Sheet, TPS40055 Wide-Input Synchronous Buck Controller (SLUS593). 2. T echnical Brief, PowerP AD Thermally Enhanced Package (SLMA002). ...
-
Texas Instruments HPA070 - page 17
IMPORT ANT NOTICE T exas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orde ...
Texas Instruments HPA070についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもTexas Instruments HPA070の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTexas Instruments HPA070で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。