Bryant 383KAVの取扱説明書

12ページ 0.2 mb
ダウンロード

ページに移動 of 12

Summary
  • Bryant 383KAV - page 1

    SAFETY CONSIDERATIONS NOTE: Read the entire instruction manual before performing any service or maintenance. This symbol → indicates a change since the last issue. These procedures are for size 45,000 through 155,000 Btuh input units. Index Page SAFETY CONSIDERATIONS ..................................................1-2 ELECTROSTATIC DISCHARGE (E ...

  • Bryant 383KAV - page 2

    WARNING: The ability to properly perform mainte- nance on this equipment requires certain expertise, me- chanical skills, tools, and equipment. If you do not possess these, do not attempt to perform any maintenance on this equipment other than those procedures recom- mended in the User’s Manual. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN POSS ...

  • Bryant 383KAV - page 3

    1. Downflow/Horizontal Each furnace requires 2 filters which are installed in the return-air duct. (See Fig. 4 and 5.) To remove filters for cleaning or replacement, proceed as follows: a. Disconnect electrical power before removing blower access door. b. Remove screw from front of door and remove blower access door. c. Reach up behind top plate, t ...

  • Bryant 383KAV - page 4

    a. Remove dust caps or plugs from oil ports located at each end of motor. b. Use a good grade of SAE 20 nondetergent motor oil and put 1 teaspoon, 5 cc, 3/16 oz, or 16 to 25 drops in each oil port. Do not over-oil. c. Allow time for total quantity of oil to be absorbed by each bearing. d. Wipe excess oil from motor housing. e. Replace dust caps or ...

  • Bryant 383KAV - page 5

    (2.) Use 1/4-in. diameter wire brush (commonly known as 25-caliber rifle cleaning brush). NOTE: The materials needed in items (1.) and (2.) can usually be purchased at local hardware stores. (3.) Insert twisted wire end of brush into end of steel spring cable, and crimp tight with crimping tool or strike with ball-peen hammer. TIGHTNESS is very imp ...

  • Bryant 383KAV - page 6

    The electrical ground and polarity for 115-v wiring must be maintained properly. Refer to Fig. 10 for field wiring information and to Fig. 12 for unit wiring information. NOTE: If the polarity is not correct, the STATUS LED on the control center will flash rapidly and prevent the furnace from operating. The control system also requires an earth gro ...

  • Bryant 383KAV - page 7

    → Fig. 10—Heating and Cooling Application Wiring Diagram A98209 115-V FIELD-SUPPLIED DISCONNECT AUXILIARY J-BOX CONTROL BOX 24-V TERMINAL BLOCK THREE-WIRE HEATING- ONLY FIVE WIRE NOTE 1 NOTE 2 FIELD-SUPPLIED DISCONNECT CONDENSING UNIT TWO WIRE FURNACE R G C WC R GY GND GND FIELD 24-V WIRING FIELD 115-, 208/230-, 460-V WIRING FACTORY 24-V WIRING ...

  • Bryant 383KAV - page 8

    → Fig. 12—Wiring Diagram A98200e PCB BLOWER O FF DE LAY SELECTI O N CH ART 90 SEC 135 SEC 180 SEC 225 SEC GVR H I/L O RELAY SEC-1 SEC- 2 PL1 32 1 6 5 4 987 LED TEST/TW IN BLOWER OFF DELAY G R Y W C HUM HSIR IDR BLWR BLOWER SPEED SELECT FU1 COOL HEAT L2 PL3 PL2 VAC 120 L1 PR1 1 2 1 2 3 PR2 24 VAC-3A FUSE SPARE-2 SPARE-1 EAC-1 EAC-2 C 1. 5 A M ...

  • Bryant 383KAV - page 9

    Fig. 13—Service Label A96263 SERVICE 11 NO PREVIOUS CODE - Stored status codes are erased when power ( 115V or 24V) to control is interrupted or 48 hours after ea ch fault is cleared. 12 BLOWER ON AFTER POWER UP (115V or 24V) - Blowe r runs for 90 seconds, if unit is powered up during a call for heat (R-W closed). 13 LI MIT OR FLAME ROLL-OU T SWI ...

  • Bryant 383KAV - page 10

    Is circuit breaker closed? Close door switch and go to start. Is red LED status light on? Is door switch closed? Is red LED status light blinking rapidly without a pause? Is there 115v going to switch? Replace door switch. Replace control center. Replace transformer. Is red LED status light blinking ON/OFF slowly with a combination of shor ...

  • Bryant 383KAV - page 11

    11 NO PREVIOUS FAULT - Faults are erased after 48 hrs or whenever power (115V or 24V) is interrupted. Run system through a heating or cooling cycle to recheck system. 12 BLOWER ON AFTER POWER UP (115V OR 24V) - Normal  operation. Blower will run for 90 sec when furnace power is interrupted during a call for heat and R- ...

  • Bryant 383KAV - page 12

    A94328 SERVICE TRAINING Packaged Service Training programs are an excellent way to increase your knowledge of the equipment discussed in this manual, including:  • Unit Familiarization • Maintenance  • Installation Overview • Operating Sequence A large selection of product, theory, and skills programs is availa ...

メーカー Bryant カテゴリー Furnace

Bryant 383KAVのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 383KAVの取扱説明書
- Bryantの製品カード
- パンフレット
- またはBryant 383KAVの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Bryant 383KAVの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Bryant 383KAVの取り付け説明書、サービスマニュアル、簡易説明書、またはBryant 383KAVのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Bryant 383KAVの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Bryant 383KAVデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがBryant 383KAVを使用するのを助ける技術的文書のことです。説明書は通常、全てのBryant 383KAVユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Bryantの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Bryant 383KAVの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははBryant 383KAVの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Bryant 383KAVに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Bryant 383KAVデバイスの基本機能を使うにあたってのヒント。 Bryant 383KAVのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Bryant 383KAVに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるBryant 383KAVのメーカー/サービスへの連絡先に関する情報。

Bryant 383KAVについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもBryant 383KAVの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBryant 383KAVで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)