Drolet 1400-Iの取扱説明書

23ページ 0.29 mb
ダウンロード

ページに移動 of 23

Summary
  • Drolet 1400-I - page 1

    45221 OWNER`S MANUAL Escape 1400-I Insert US ENVIRONMENTAL PROTECTION AGENCY PHASE II CERTIFIED WOOD INSERT Verified and tested following ULC S628 and UL 1482 Standards by: Manufactured by : STOVE BUILDER INTERNATIONAL INC. . 1700, Léon-Harmel, Québec (Québec) G1N 4R9 Tel : (418 ) 527-3060 Fax : (418 ) 527-4311 www.d ro le t. ca READ AND KEEP TH ...

  • Drolet 1400-I - page 2

    1 INTRODUCTION SBI INC., one of the most im portant wood stove and fireplac e manufacturers in Canada, congratulates you on your purc hase and wishes to help you get maximum satisfaction from your wood insert. In the pages that follow, we will give you advice on wood heating and controlled combustion as well as t echnical specificat ions regarding ...

  • Drolet 1400-I - page 3

    2 TABLE OF CONTENTS INTRODUCTION .............................................................................................................................. .......................1 Section 1.0 Pre-Insta llation Requirements ..................................................................................... ........................4 1.1 Masonr ...

  • Drolet 1400-I - page 4

    3 Escape 1400-I Dimensions 13 29/64" 28 25/64" 26 29/32" 6.000" O 9 61/64" 20 31/32" 13 3/8" 6 31/64" 8 9/32" 8 9/64" 15 1/32" 20 31/32" Faceplate fully extended toward the back Faceplate fully extended toward the front ...

  • Drolet 1400-I - page 5

    4 Section 1.0 Pre-Installation Requirements 1.1 Masonry & Zero Clearance Requirements The masonry fireplace must m eet the minimum code re quirem ents, or NFPA 211 or the equivalent for a safe installation. Contact your local Building Inspector for requirements in your area. An inspection of the fireplace should include the following: 1. CONDIT ...

  • Drolet 1400-I - page 6

    5 1.2 Venting Requirements The flue is a critical component to a satisfactory installation. Your Drolet insert will attain its best performance if installed with a chimney that genera tes its own draft. The mi nimum requirem ent of a flue will be the installation of a flue connector (t he liner must conform to UL1777 chimney liners) from the insert ...

  • Drolet 1400-I - page 7

    6 Section 2.0 Installation 2.1 Clearances To Combustibles (Measured From Insert Body) Escape 1400-I Sidewall (A) 13” (330 mm) Shelf (B) 22” (559 mm) Side mantle (C) 10” (254 mm) Top mantel (D) 29” (737 mm) Table 2.1 CLEARANCES Figure 2.1 Note: If side mantle protrudes more than 1.5” (38mm) in front of face of fireplace, then use sidewall ...

  • Drolet 1400-I - page 8

    7 2.1.1 Hearth Requirements If the non-combustible hearth is flush with the floor, then the hearth must be 16”/406m m (18”/450mm in Canada) in front of the fan housing (see Figure 2.1.2). If the non- combustible hearth is a minim um of 4” (102mm ) above the floor, then the hearth can be 6” (152mm) out from the fan housing with a 10” (254m ...

  • Drolet 1400-I - page 9

    8 2.3 Safety Information NOTE: This appliance is not recommended for use in a home if an occupant has any respiratory or any other related problems. 1. It is important to follow the installation and operation instructions. An improperly installed or operated insert could result in a safety hazard or fire, or damage to the unit, which would not be c ...

  • Drolet 1400-I - page 10

    9 2.4 Installation Instructions 1. Inspect the fireplace according to the safety in formation and fireplace requirements and have it cleaned and/or upgraded as necessary. 2. If the installation of the unit renders the existing damper control inaccessible, it will be necessary to either secure the damper wide open or remove it entirely. An inaccessi ...

  • Drolet 1400-I - page 11

    10 2.5 Air control plate, facepla te and fan Assembly Instructions 1. Place the faceplate panels with the finished side down on a flat, soft, non-abrasive surface. 2. Assemble the faceplate trim, attaching the mitered corners with the corner brackets. (see Figure 2.4) 3. Line up the holes of the side and top panels and secure with the screws, washe ...

  • Drolet 1400-I - page 12

    11 3.1 Safety Information 1. This insert is designed for safe operation W HEN B URNING C ORDWOOD O NLY . Altering or modifying the unit or the installation without proper aut horization will void the certification, warranty, and safety listing, and may result in a safety hazard. 2. For safety reasons, never leave the unit unattende d with the door ...

  • Drolet 1400-I - page 13

    12 homes, could possibly cause smoke spillage into the room . Smoke may contain carbon monoxide, which is poisonous, and in sufficient quantities is a health hazard. 11. We recomm end that you have a fresh air or make up ai r supply for the insert. In Canada this is a building code requirement. If this is not done, it could cause poor air quality i ...

  • Drolet 1400-I - page 14

    13 For recommended wood sizes, refer to the specifications. Common Heating Values of Cordwood Hardwoods Million Btu/Cord Softwoods Million Btu/Cord Birch 23.6 Douglas Fir 20.6 White Oak 28.3 Hemlock 17.1 Alder 17.6 Jack Pine 18.4 Table 3.1 3.2.1 Simple Wood Moisture Test Add one large piece of wood to the top of an establishe d fire. If it starts t ...

  • Drolet 1400-I - page 15

    14 established. Once the firebox is hot, the draft control can be partially closed by moving the knob to the left to adjust the intensity of the fire. Use Table 3.2 to adjust the draft control to the desired burn rate: Draft Settings Burn Rate Draft Setting Low Push Control to end of travel. Medium Low Pull Control by 3/8” from closed position. M ...

  • Drolet 1400-I - page 16

    15 3.5 Maintaining The Fire Your Drolet insert will work best if a thick bed of hot embers is m aintained in the bottom of the firebox, and a minimum of two larg e pieces of seasoned fuel are added. Combustion efficiency is largely related to establishing a hot ember bed, and hot firebox temperatures. The quicker the insert and fuel get up to opera ...

  • Drolet 1400-I - page 17

    16 Section 4.0 Maintenance 4.1 Care And Cleaning Clean the insert frequently so that soot, ash and cr eosote do not accumulate. D o not attempt to clean the insert, glass or door when the unit is hot. Special car e must be taken with plated surfaces in order to maintain the finish at its original brilliance. Do not use an abrasive glass cleaner whi ...

  • Drolet 1400-I - page 18

    17 CAUTION : Ashes can start fires, even after severa l days of inactivity. Never dispose of ashes in a combustible container. Remove ashes only when the insert and ashes are cold . Ashes should be removed from the in sert frequently. W hen ashes are removed, they should be placed in a metal container with a tightly fitting lid. The closed containe ...

  • Drolet 1400-I - page 19

    18 4.4 Baffle Installation for Escape 1400-I Figure 4.1 – Baffle installation & removal for Escape 1400-I The baffle assembly must be properly in place for co rrect burning operation. Have any damaged firebricks replaced. Check the firebricks annually for damage a nd replace if they are broken or damaged. See Figure 3.3 for the firebrick layo ...

  • Drolet 1400-I - page 20

    19 4.5 Secondary Air Tube Replacement (see Figure 4.3) 1. Remove cotter pin at RH end of tube. 2. Slide tube to left and lower tube end below RH plenum. 3. Slide tube to right to remove. 4. Reassem ble in reverse order using a new cotte r pin. The cotter pin is a hammerlock style and locks into place by hitting the head sharply with a hammer. 5. No ...

  • Drolet 1400-I - page 21

    20 Figure 4.3 – Secondary Air Tube replacement 4.6 Fan Maintenance & Care Clean the fan air inlet louvres and squirrel cage im peller regularly. The fan s hould be kept clean and dust free. Life of the fan will be shortened if opera ted in a dust filled environment, or if the fan is overheated by restricting air supply. Stalling the rotor, or ...

  • Drolet 1400-I - page 22

    21 Section 5.0 Specifications 5.1 Escape 1400-I Insert Model Fuel Type Cordwood Test Standards ULC S628 (CSA B366.2) & UL 1482 residential. Heat Output Max of 39000 BTU/Hr with EPA test wood BTU/Hr (63% default efficiency) Range Will vary with usage depending on the type and condition of cord wood. Shipping Weight 370lbs (168kg) Firebox Volume ...

  • Drolet 1400-I - page 23

    22 DROLET LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original c onsumer purchaser and is not transferable. This warranty covers brand new products only, which have not been altered, modified nor repaired since sh ipm ent from factory. Proof of pu rchase (dat ed bill of sale), model nam e and serial number must be ...

メーカー Drolet カテゴリー Stove

Drolet 1400-Iのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 1400-Iの取扱説明書
- Droletの製品カード
- パンフレット
- またはDrolet 1400-Iの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Drolet 1400-Iの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Drolet 1400-Iの取り付け説明書、サービスマニュアル、簡易説明書、またはDrolet 1400-Iのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Drolet 1400-Iの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Drolet 1400-Iデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDrolet 1400-Iを使用するのを助ける技術的文書のことです。説明書は通常、全てのDrolet 1400-Iユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Droletの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Drolet 1400-Iの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDrolet 1400-Iの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Drolet 1400-Iに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Drolet 1400-Iデバイスの基本機能を使うにあたってのヒント。 Drolet 1400-Iのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Drolet 1400-Iに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDrolet 1400-Iのメーカー/サービスへの連絡先に関する情報。

Drolet 1400-Iについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDrolet 1400-Iの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDrolet 1400-Iで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)