QSC EB2082-iの取扱説明書

20ページ 2.72 mb
ダウンロード

ページに移動 of 20

Summary
  • QSC EB2082-i - page 1

    TD-000218-00 revD ILA Series Loudspeaker Sy stem User Manual WL2082-i full-range line array lou dspeaker WL115-sw subwoofer line array loudsp eaker FB2082-i array frame EB2082-i extensi on bar PB2082-i pull back bar GS115-sw ground stack kit *TD-000218-00* 1675 MacArthur Blv d., Costa Mesa, CA, 92626 USA Main Number (714) 754 -6175 Sales & Mark ...

  • QSC EB2082-i - page 2

    2 IMPORT ANT SAFETY PRECAUTIONS Install in accordance with QSC Audio Product's instructions and under the supervision of a licensed Professional Engineer . WA R NI N G ! Before placing, installing, ri gging, or suspending any speaker product, inspec t all hardware, suspension, cabinets, transducers , brackets and associated equipment for damag ...

  • QSC EB2082-i - page 3

    3 Introduction The Installation Line Array (ILA) is a high performance line array system designed for the needs of Houses of W orship, Performi ng Arts facilities and a multitude of other venue ty pes. The current ILA family is composed of the WL2082-i line array element, WL115-s w sub- woofer , FB2082-i array frame, PB2082-i pull-back bar , EB 208 ...

  • QSC EB2082-i - page 4

    4 Introduction (continued) WL115-sw The WL115-sw subwoofer extends the system’ s low-frequency capability to 35 Hz. with a compact fourth-order bandpass enclosure. Its ceramic magnet, 4” voice coil, 15” transducer provides 650 watt continuous power handling capability . Many users of line array systems hav e found that suspending the subwoofe ...

  • QSC EB2082-i - page 5

    5 Figure 3: FB2082-i Array Frame 1- Shackle holes (accept 3/4” (20 mm) screw pin anchor sh ackle) 2- Center support bar 3- Rigging plates 4- Rigging plate retai ning bolts 5-Rigging plate attac hment holes Figure 4: PB2082-i Pull Back Bar 1- Shackle hole (acce pts 5/8” (16 mm) screw pin an chor shackle) 2- Rigging plate atta chment holes 3- Rig ...

  • QSC EB2082-i - page 6

    6 Rigging the Installation Line Array Rules for Suspension •Correct use of all suspension hardware and components is imperative in sound system rigging and deployment. •Always calculate suspended loads before lifting to ensure suspension components and hardware are used within their respective load limits. •Research local codes and regulation ...

  • QSC EB2082-i - page 7

    7 Rigging the Installatio n Line Array (continued) 1- Working L oad Limits are per f astener loaded in doub le shear . Data is for informatio nal purposes only . Attaching WL2082-i to Array Frame Before beginning any installation, have your syst em designer configure the array with proper splay angles using QSC’ s EASE Focus (Array Calcul ator). ...

  • QSC EB2082-i - page 8

    8 Rigging the Installation Line Array (continued) Pull-Back Bar If using the pull-back bar , attach to the bottom enclosure at the bot- tom-most splay angle adjustment holes at the rear of the rigging plate by inserting the cap-head shoulder bolt through the mated piec es and threading the lock nut (nylock) on the inside edge of the plates. Use a 5 ...

  • QSC EB2082-i - page 9

    9 Rigging the Installation Line Array (continued) 3- Lower the array frame onto the enclosure, carefully aligning the rigging straps, and attach the top enclosure to the array frame by installing the ball-lock pins or M8 bolts. Before lifting, ensure the audio connection to the enclosures are correct and functioning. NOTE: When attaching one WL115- ...

  • QSC EB2082-i - page 10

    10 Rigging the Installation Line Array (continued) Attaching WL115-sw behind WL2082-i array using EB2082-i It is sometimes necessary to suspend the subwoofers behind the main array . Extrem e splay angles may result in physical interference with rear -flown subwoofers . Attach both array frames to the extension bar rigging plates by centering the a ...

  • QSC EB2082-i - page 11

    11 WL2082-i Controls and Connections MODE Selection Switch BI AMP: When set to BI AMP , an internal shading net- work removes the mid-frequencies from one of the low- frequency drivers. The BI AMP HORIZONT AL SHADING switch will select which transducer is shaded. TRI AMP: Shading network is NOT applied (shading must be provided by upstream signal p ...

  • QSC EB2082-i - page 12

    12 WL115-sw Connections Input Connections The WL115-sw input connectors are a pair of Neutrik NL8's wired in parallel. See T able 3 or the WL115-sw Input Plate for connector pinout. Note pin numbers 2+, 2-, 3+, 3-, 4+, and 4- are wired straight throug h from one connector to the other . This accommod ates using one i nput cable assembly (where ...

  • QSC EB2082-i - page 13

    13 WL2082-i Specifications Frequency Response: 80 - 20,000 Hz (+/- 3 dB) Frequency Range: 68 - 22,000 Hz (-10 dB) Maximum SPL (continuous/peak): HF: 126/132 dB LF: 122/128 dB Nominal Coverage (-6 dB included): Horizontal: 140 degrees (500 Hz to 3.2 kHz)V ertical: dependant on cumulative splay angle T ransducers: High Frequency: Dual 50W , 8 Ohm 1 i ...

  • QSC EB2082-i - page 14

    14 WL115-sw Specifications Frequency Response: 37 - 107 Hz (+/- 3 dB) Frequency Range: 35 - 112 Hz (-10 dB) Maximum SPL (continuous/peak): 124 dB/130 dB T ransducer: 650W , 8 Ohm 15 inch woofer , 4 inch voice coil, ceramic magnet assembly Recommended Crossover Frequency: 35 - 85 Hz Input Sensitivity: 96 dB Weight: Net: 111 lb (50.4 kg) Shipping: 12 ...

  • QSC EB2082-i - page 15

    15 EB2082-i Specifications Material: Aluminum 6061-T6 Finish: Black powder coat (White optional) Working Load Limit Informatio n: FB2082-i Specifications Material: Aluminum 6061-T6 Finish: Black powder coat (White optional) Working Load Limit Informatio n: Component Weight 7:1 Design Facto r 10:1 Design Factor 12:1 Design Factor EB2082-i Extension ...

  • QSC EB2082-i - page 16

    16 PB2082-i Specifications Material Aluminum 6061-T6 Finish Black powder coat (White optional) Working Load Limit Information: GS115-sw Specifications Material Aluminum 6061-T6 Finish Black powder coat (White optional) Weight 5 lb (2.3 kg) per set Component Weight 7:1 Design Factor 10:1 Desig n Factor 12:1 Design Factor PB2082-i Pull Back Bar 6 lb ...

  • QSC EB2082-i - page 17

    17 ...

  • QSC EB2082-i - page 18

    18 ...

  • QSC EB2082-i - page 19

    19 ...

  • QSC EB2082-i - page 20

    QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA ©2006 ,2007 “QSC” and the QSC logo are registered with the U.S. Patent and T rademark Office. How to Contact QSC Audio Products Mailing address: QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, CA 92626-1468 USA T elephone Numbers: Main Number (714) ...

メーカー QSC カテゴリー Portable Speaker

QSC EB2082-iのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- EB2082-iの取扱説明書
- QSCの製品カード
- パンフレット
- またはQSC EB2082-iの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、QSC EB2082-iの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、QSC EB2082-iの取り付け説明書、サービスマニュアル、簡易説明書、またはQSC EB2082-iのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、QSC EB2082-iの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

QSC EB2082-iデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがQSC EB2082-iを使用するのを助ける技術的文書のことです。説明書は通常、全てのQSC EB2082-iユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

QSCの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. QSC EB2082-iの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははQSC EB2082-iの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。QSC EB2082-iに関してこのドキュメントで見つけることができる全てのヒントの目次
3. QSC EB2082-iデバイスの基本機能を使うにあたってのヒント。 QSC EB2082-iのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。QSC EB2082-iに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるQSC EB2082-iのメーカー/サービスへの連絡先に関する情報。

QSC EB2082-iについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもQSC EB2082-iの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQSC EB2082-iで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)