-
Harbor Freight Tools 40070 - page 1
HAND FINISHING ORBIT AL SANDER ASSEMBL Y AND OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yright © 2002 by Harbor F reight T ools ® . All r ights reser v ed. No por tion of this manual or any ar twork contained herein may be reproduced in any shape or f or m withou ...
-
Harbor Freight Tools 40070 - page 2
Page 2 SKU 40070 For technical questions, please call 1-800-444-3353. SA VE THIS MANU AL Y ou will need this manual f or the safety warnings and precautions, assembl y , operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep y our in v oice with this manual. Write the in voice n umber on the inside of the ...
-
Harbor Freight Tools 40070 - page 3
Page 3 SKU 40070 For technical questions, please call 1-800-444-3353. ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in an y way . Do not use an y adapter plugs. Check with a qualified electrician if y ...
-
Harbor Freight Tools 40070 - page 4
Page 4 SKU 40070 For technical questions, please call 1-800-444-3353. 14. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. 15. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection ...
-
Harbor Freight Tools 40070 - page 5
Page 5 SKU 40070 For technical questions, please call 1-800-444-3353. SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Sander . These carr y impor tant information. If unreadable or missing, contact Harbor F reight T ools f or a replacement. 2. When using a handheld power tool, always maintain a firm grip on the tool with both hands t ...
-
Harbor Freight Tools 40070 - page 6
Page 6 SKU 40070 For technical questions, please call 1-800-444-3353. and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic par ticles. (California Health & Safety Code § 25249.5, et seq. ) 8. T ake caution as some w oods contain preservatives suc h as copper chr omium arsenate ...
-
Harbor Freight Tools 40070 - page 7
Page 7 SKU 40070 For technical questions, please call 1-800-444-3353. wire connected to the tool’ s grounding system and must ne v er be attached to an electrically “live” terminal. (See Figure A.) 3. Y our tool must be plugged into an appropr iate outlet, proper ly installed and grounded in accordance with all codes and ordinances. The plug ...
-
Harbor Freight Tools 40070 - page 8
Page 8 SKU 40070 For technical questions, please call 1-800-444-3353. EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2 . As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequat ...
-
Harbor Freight Tools 40070 - page 9
Page 9 SKU 40070 For technical questions, please call 1-800-444-3353. SYMBOLOGY UNP A CKING When unpacking, chec k to make sure that the item is intact and undamaged. If any par ts are missing or broken, please call Harbor F reight T ools at the number shown on the co ver of this manual as soon as possible. ASSEMBL Y INSTR UCTIONS NO TE: For additi ...
-
Harbor Freight Tools 40070 - page 10
Page 10 SKU 40070 For technical questions, please call 1-800-444-3353. ATT A CHING SANDP APER T O THE BA CKING PAD (28) 1. Press the tab on the Clamps (6) inward on both sides of the unit and swing the clamps on both sides up , out, and down. See 1 & 2 , right. 2. Cut the sandpaper to fit the 4” W x 4 1 / 2 ” L Pad (28) , with a little extr ...
-
Harbor Freight Tools 40070 - page 11
Page 11 SKU 40070 For technical questions, please call 1-800-444-3353. INSPECTION, MAINTENANCE, AND CLEANING 1. W ARNING! Make sure the P ower Switch (3) of the Sander is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EA CH USE, ins ...
-
Harbor Freight Tools 40070 - page 12
Page 12 SKU 40070 For technical questions, please call 1-800-444-3353. ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and shown for illustr ation purposes only , and are not av ailable individu- ally as replacement par ts. Part 0 - Dust Collection Chute - not shown. ...
Harbor Freight Tools 40070についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHarbor Freight Tools 40070の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 40070で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。