Snapper NZMX30614KH, NZMX32734BVの取扱説明書

40ページ 3.89 mb
ダウンロード

ページに移動 of 40

Summary
  • Snapper NZMX30614KH, NZMX32734BV - page 1

    Safety Instructions & Operator's Manual for NOTE: Specifications are correct at time of printing and are subject to change without notice. * Actual sustained engine power will likely be lower due to operating limit ations and environment al factors. COPYRIGHT © 2006 SNAPPER - A DIVISION OF SIMPLICITY MFG ., INC. ALL RIGHTS RESER VED MANUA ...

  • Snapper NZMX30614KH, NZMX32734BV - page 2

    2 ! ! IMPORT ANT SAFETY INSTRUCTIONS W ARNING: This powerful cutting machine is capable of amput ating hands and feet and can throw object s that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must underst and th ...

  • Snapper NZMX30614KH, NZMX32734BV - page 3

    3 ! ! IMPORT ANT SAFETY INSTRUCTIONS PREP ARA TION 1. Read, underst and and follow instructions and warn- ings in this manual and on the machine, engine and att achment s. Know the controls, the safety signs and the proper use of the machine before st arting. If the operators or mechanics cannot read English, it is the owner ’ s responsibility to ...

  • Snapper NZMX30614KH, NZMX32734BV - page 4

    4 ! ! IMPORT ANT SAFETY INSTRUCTIONS OPERA TION (Continued From Previous Page) 7. Blades must be OFF except when cutting grass. Set blades in highest position when mowing over rough ground. 8. Keep hands and feet away from rot ating blades underneath deck. DO NOT place foot on ground while BLADES are ON or machine is in motion. 9. DO NOT operate ma ...

  • Snapper NZMX30614KH, NZMX32734BV - page 5

    5 IMPORT ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . .2-4 T ABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ST A TEMENT OF USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ENGINE POWER RA TING INFORMA TION . . . . . . . . . . . . . .5 SECTION 1 - F AMILIARIZA TION . . . . . . . . . . . . . . . . . . ...

  • Snapper NZMX30614KH, NZMX32734BV - page 6

    6 Section 1 - F AMILIARIZA TION FIGURE 1.1 1.1 INTRODUCTION This manual has been prepared for the operator’s of the SNAPPER MID MOUNT Z-RIDER. It s purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and Follow the I ...

  • Snapper NZMX30614KH, NZMX32734BV - page 7

    7 Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROT A TING P ARTS KEEP AW A Y FROM MOVING P ARTS P ARKING BRAKE LEVER OPERA TION MOTION CONTROL LEVER OPERA TION WEAR HEARING PROTECTION W ARNING ! A VOID SERIOUS INJUR Y OR DEA TH ST ARTING , OPERA TION & STOPPING OF MACHINE ...

  • Snapper NZMX30614KH, NZMX32734BV - page 8

    FUEL GAUGE (2) CONTROL P ANEL IDENTIFICA TION DANGER! ROT A TING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA FUEL T ANK SELECT IGNITION SWITCH STOP RUN ST ART 8 Section 2 - SAFETY MESSAGES AND SYMBOLS ...

  • Snapper NZMX30614KH, NZMX32734BV - page 9

    9 Section 2 - SAFETY MESSAGES AND SYMBOLS ROLL BAR PROTECTIVE STRUCTURE DECALS CAUTION! SPRING LOADED MECHANISM Cutting Hazard Fans rotate while engine is running. Keep away while engine is running. W ARNING A TTENCION Peligro de corte Los ventiladores giran mientras el motor esta funcionando. Mantengase lejos mientras el motor esta funcionando. 71 ...

  • Snapper NZMX30614KH, NZMX32734BV - page 10

    10 Section 3 - OPERA TING INSTRUCTIONS 3.1 PRE-ST ART CHECK LIST Make the following checks and perform the service required before each start-up. 3.1.1. Check tires and add or release air as needed to bring pressure to 12 psi in drive tires. Pressure in front caster wheels should be 25 psi. 3.1.2. Check guards, deflectors and covers to make sure al ...

  • Snapper NZMX30614KH, NZMX32734BV - page 11

    11 Section 3 - OPERA TING INSTRUCTIONS Section 3 - OPERA TING INSTRUCTIONS ROLL RELEASE: T o roll the machine without the engine running, pressure within the hydraulic pump s must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to release the pressure. Use a wrench to rot ate both relief valves co ...

  • Snapper NZMX30614KH, NZMX32734BV - page 12

    12 Section 3 - OPERA TING INSTRUCTIONS Section 3 - OPERA TING INSTRUCTIONS 3.2.1. ST ARTING ENGINE NOTE: If after 5 seconds of cranking the engine does not start, release the key . Attempt starting again af ter waiting for approximately 20 seconds. 7. After engine st arts, move the choke control to the "OFF" or no choke position. Allow a ...

  • Snapper NZMX30614KH, NZMX32734BV - page 13

    13 Section 3 - OPERA TING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 1. Depress deck lift pedal fully to lock deck in trans- port position. See Figure 3.9. 2. Insert stop pin to desired cutting height. See Figure 3.10. 3. Depress deck lift pedal while flipping back transport lever , and slowly release pedal to lower deck. See Figure 3.1 1. NOTE: Th ...

  • Snapper NZMX30614KH, NZMX32734BV - page 14

    14 Section 3 - OPERA TING INSTRUCTIONS 3.4.2. STOPPING MACHINE 1. Return motion control levers to the neutral position & the neutral lock position. IMPORT ANT : Operator must use hand assistance to bring both motion control levers to the neutral position & the neutral lock position. 2. Engage parking brake. 3. Push Blade Switch down to the ...

  • Snapper NZMX30614KH, NZMX32734BV - page 15

    15 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.1 INTRODUCTION T o retain the quality of the SNAPPER mower , use gen- uine SNAPPER replacement part s only . Contact a local SNAPPER dealer for part s and service assis- tance. For the correct p art or information for a particu- lar SNAPPER mower , always mention the model and serial ...

  • Snapper NZMX30614KH, NZMX32734BV - page 16

    16 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.2.3. CHECK MOWER DRIVE BEL T 1. Lower deck to lowest setting. 2. Remove footrest. See Figure 4.3. 3. Removal of footrest will allow access to deck belt. 4. Check the belt tension. The idler pulleys and springs provide proper tension and require no adjust- ments. If belt is frayed, sli ...

  • Snapper NZMX30614KH, NZMX32734BV - page 17

    17 Section 3 - OPERA TING INSTRUCTIONS 4.5 ANNUALL Y (END OF EACH SEASON) Perform all maintenance as described in Section "AFTER EVERY 25 OPERA TING HOURS". Refer to Section "Service Schedule". 4.5.1. ENGINE Service engine according to engine owner's manual. Section 4 - MAINTENANCE 4.3.3. RIDING MOWER - LUBRICA TION 1. Fron ...

  • Snapper NZMX30614KH, NZMX32734BV - page 18

    18 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.5 ANNUALL Y (END OF EACH SEASON) (Continued from previous Page) 4.5.2. FUEL FIL TER Service fuel filter as instructed below . T urn key to "OFF" position. Engine MUST be stopped and MUST be cold before removing filter . Clamp fuel line to pre- vent fuel spillage or perform f ...

  • Snapper NZMX30614KH, NZMX32734BV - page 19

    19 Section 3 - OPERA TING INSTRUCTIONS Section 4 - MAINTENANCE 4.6 DECK REMOV AL (Continued from previous p age) 6. Remove inside nuts that secure fittings to front lift arms. See Figure 4.10. 7. Remove inside nuts that secure eyebolt s to rear lift arms. See Figure 4.1 1. 8. Remove engine to deck belt from around deck pulley . NOTE: Disconnecting ...

  • Snapper NZMX30614KH, NZMX32734BV - page 20

    20 Section 3 - OPERA TING INSTRUCTIONS 10. If wheel(s) are rotating, loosen the hydro pump activation assembly retaining screw . Move activation assembly forward or rearward to stop rotation of wheel. Retighten retaining screw . Repeat this step for other hydro pump. See Figure 5.3. NOTE: On some pumps, the ret aining screw is located on the upper ...

  • Snapper NZMX30614KH, NZMX32734BV - page 21

    21 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.1 NEUTRAL POSITION ADJUSTMENTS (Continued From Previous Page) 12. With motion control levers remaining in the neutral lock position, See Figure 3.7, hold connecting rod up to the activation assembly and check length of rod. T ie rod end bolt must align with the activatio ...

  • Snapper NZMX30614KH, NZMX32734BV - page 22

    22 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.2.1. MOWER DECK ADJUSTMENT (LEVELNESS) SIDE to SIDE and FRONT to REAR 8. Loosen the bottom nuts that secure both rear deck support eyebolts. Adjust top nuts until eyebolts are tight, then tighten bottom nuts securely . See Figure 5.6. 9. Set the mower deck to the transpo ...

  • Snapper NZMX30614KH, NZMX32734BV - page 23

    23 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.3 TRACTION BEL T TENSION The traction drive belt tension does not require adjustment. If the belts are slipping, they will have to be replaced. 5.4 TRACTION BEL T REPLACEMENT 1. Remove clutch to deck belt. Refer to Section “Mower Drive Belt Replacement”. 2. T urn hex ...

  • Snapper NZMX30614KH, NZMX32734BV - page 24

    24 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.6 TRACKING ADJUSTMENT If the machine does not track straight when the Motion Control Levers are in the maximum forward speed position, perform the following adjustment. Rear tire pressure must be set to 12 PSI before making this adjustment. 1. Loosen bolts that secure ad ...

  • Snapper NZMX30614KH, NZMX32734BV - page 25

    25 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.8 ENGINE ADJUSTMENTS & REP AIR Refer to the engine owner's manual for engine adjust- ments and/or rep airs. 5.9 MOWER BLADE REPLACEMENT 5.9.1. BLADE WEAR LIMITS 1. Inspect blade frequently for signs of excessive wear or damage. Replace blade when it reaches the ...

  • Snapper NZMX30614KH, NZMX32734BV - page 26

    26 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.10 BA TTER Y NOTE: In order to raise operator set to access battery comp artment, seat must be in rearmost position. 5.10.1. BA TTER Y REMOV AL 1. Slide terminal cover away from positive terminal. 2. Observe and note cable positions on battery . Disconnect cables from ba ...

  • Snapper NZMX30614KH, NZMX32734BV - page 27

    27 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.10.4. BA TTER Y TESTING 1. Remove battery . Refer to Section "BA TTERY REMOV AL". 2. Using a voltmeter , check the battery's state of charge by comparing the voltmeter reading with the chart below . (Remember to hook the positive (red) lead of the voltmete ...

  • Snapper NZMX30614KH, NZMX32734BV - page 28

    28 Section 3 - OPERA TING INSTRUCTIONS Section 5 - ADJUSTMENTS & REP AIR 5.1 1 HYDRAULIC SYSTEM, PURGING After replacing or rep airing hydraulic system compo- nents, one or both of the wheel drives may not pull properly . This is likely to be caused by air entrapped in the system. If you experience a pulling issue after completing repairs, perf ...

  • Snapper NZMX30614KH, NZMX32734BV - page 29

    29 Section 3 - OPERA TING INSTRUCTIONS TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION St arter Will Not Crank Engine 1. Battery dead. 1. Service battery . 2. Blown fuse. 2. Replace fuse. 3. Electrical connections loose or corroded. 3. Clean and check connections for good contact. 4. Defective ignition switch. 4. Contact authorized SNAPPER ...

  • Snapper NZMX30614KH, NZMX32734BV - page 30

    30 Section 3 - OPERA TING INSTRUCTIONS TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Machine Will Not Move Loss Of T raction 1. Motion Control Levers in the neutral "N" position. 1. Move Motion Controls to desired speed position. 2. Hydro. Pumps in roll release setting. 2. T ighten relief valves. 3. Low transmission hydraulic o ...

  • Snapper NZMX30614KH, NZMX32734BV - page 31

    31 Section 3 - OPERA TING INSTRUCTIONS SER VICE SCHEDULE ITEM SERVICE PERFORMED REF . NUMBER EACH USE 5 HRS 25 HRS 50 HRS 100 HRS EACH SEASON Engine Oil Check Oil Level Page 10 X Initial Oil Change Page 15 X Periodic Oil Change Page 16 X* Air Cleaner Clean or Replace Engine Manual X** Sp ark Plug Replace Engine Manual X Fuel Filter Replace Page 18 ...

  • Snapper NZMX30614KH, NZMX32734BV - page 32

    32 2 YEAR LIMITED W ARRANTY For two (2) years from purchase date for the original purchaser's use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except for taxes where applicable), any p art or part s found upon examination by the factory at McDonough, Georgia, to be defective in material or workmanship or both. ...

  • Snapper NZMX30614KH, NZMX32734BV - page 33

    33 PRIMAR Y MAINTENANCE ...

  • Snapper NZMX30614KH, NZMX32734BV - page 34

    34 PRIMAR Y MAINTENANCE ...

  • Snapper NZMX30614KH, NZMX32734BV - page 35

    35 PRIMAR Y MAINTENANCE ...

  • Snapper NZMX30614KH, NZMX32734BV - page 36

    36 PRIMAR Y MAINTENANCE ...

  • Snapper NZMX30614KH, NZMX32734BV - page 37

    37 SNAPPER PRODUCT REGISTRA TION FORM IMPOR T ANT : KEEP THIS INFORMA TION FOR YOUR PERSONAL RECORDS (Complete the following information on your Snapper pur chase) Model Number_________________________________________________________ Serial Number _________________________________________________________ Date of Pur chase___________________________ ...

  • Snapper NZMX30614KH, NZMX32734BV - page 38

    38 NOTES ...

  • Snapper NZMX30614KH, NZMX32734BV - page 39

    39 NOTES ...

  • Snapper NZMX30614KH, NZMX32734BV - page 40

    40 Safety Instructions & Operator's Manual for IMPORT ANT Snapper product s are built using engines that meet or exceed all applicable emissions requirement s on the date manufactured. The labels on those engines cont ain very import ant emissions information and critical safety warnings. Read, Underst and, and Follow all warnings and inst ...

メーカー Snapper カテゴリー Lawn Mower

Snapper NZMX30614KH, NZMX32734BVのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- NZMX30614KH, NZMX32734BVの取扱説明書
- Snapperの製品カード
- パンフレット
- またはSnapper NZMX30614KH, NZMX32734BVの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Snapper NZMX30614KH, NZMX32734BVの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Snapper NZMX30614KH, NZMX32734BVの取り付け説明書、サービスマニュアル、簡易説明書、またはSnapper NZMX30614KH, NZMX32734BVのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Snapper NZMX30614KH, NZMX32734BVの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Snapper NZMX30614KH, NZMX32734BVデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSnapper NZMX30614KH, NZMX32734BVを使用するのを助ける技術的文書のことです。説明書は通常、全てのSnapper NZMX30614KH, NZMX32734BVユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Snapperの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Snapper NZMX30614KH, NZMX32734BVの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSnapper NZMX30614KH, NZMX32734BVの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Snapper NZMX30614KH, NZMX32734BVに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Snapper NZMX30614KH, NZMX32734BVデバイスの基本機能を使うにあたってのヒント。 Snapper NZMX30614KH, NZMX32734BVのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Snapper NZMX30614KH, NZMX32734BVに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSnapper NZMX30614KH, NZMX32734BVのメーカー/サービスへの連絡先に関する情報。

Snapper NZMX30614KH, NZMX32734BVについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSnapper NZMX30614KH, NZMX32734BVの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper NZMX30614KH, NZMX32734BVで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)