Extron electronic HDMI DA2の取扱説明書

32ページ 9.46 mb
ダウンロード

ページに移動 of 32

Summary
  • Extron electronic HDMI DA2 - page 1

    68-1844-01 Rev. B 10 13 HDMI DA2 User Guide HDMI ® Distribution Amplifier ...

  • Extron electronic HDMI DA2 - page 2

    Safety Instructions • English W ARNING: This symbol, D , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may pr esent a risk of electric shock. A TTENTION: This symbol, I , when used on the product, is intended to alert the user of important operating ...

  • Extron electronic HDMI DA2 - page 3

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interfer ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radi ...

  • Extron electronic HDMI DA2 - page 4

    Conventions Used in this Guide Notifications the following are used: DanGer: Danger indicates a situation that will result in death or sever e injury . W ARNING: A warning indicates a situation that has the potential to result in death or severe injury . CAUTION: A caution indicates a situation that may result in minor injury . A TTENTION: Attentio ...

  • Extron electronic HDMI DA2 - page 5

    Contents Introduction .................................................... 1 About the HDMI DA2 ....................................... 1 HDMI DA2 Features ......................................... 1 HDMI DA2 Application Diagram ....................... 2 Installation ...................................................... 3 Installation Overview ... ...

  • Extron electronic HDMI DA2 - page 6

    HDMIDA2 • Contents vi ...

  • Extron electronic HDMI DA2 - page 7

    Intr oduction This guide describes the function, installation, and operation of the Extron HDMIDA2 distribution amplifier . Unless otherwise stated, the terms “distribution amplifier” or “DA” refer to the HDMI DA2. This section provides the following information: z About the HDMI DA2 z HDMI DA2 Features z HDMI DA2 Application Diagram A ...

  • Extron electronic HDMI DA2 - page 8

    Output Compatibility Correction — The HDMI DA2 monitors the EDID of each connected display to ensure it is compatible with the curr ent input signal. The following adjustments are made for each output independently: z Interface format: If the connected display is DVI and the input signal is HDMI, the signal is reformatted to DVI. If the output is ...

  • Extron electronic HDMI DA2 - page 9

    Installation This section of the guide describes the following topics concerned with the installation and setup of the HDMI DA2 distribution amplifier . z Installation Overview z Rear Panel Features z Connecting the Power Supply z Connecting the Input Source z Connecting Output Displays z Wiring for RS-232 Control z Connecting to the USB Port Inst ...

  • Extron electronic HDMI DA2 - page 10

    Connecting the Power Supply Connect the provided 12 VDC, 1 A power supply to the HDMI DA2 by following these instructions: W ARNING: Remove power before wiring. The two power cor d wires must be kept separate while the power supply is plugged in. A TTENTION: • This product is intended to be supplied by a Listed Power Unit marked “Class2” o ...

  • Extron electronic HDMI DA2 - page 11

    Connecting the Input Sour ce Use an HDMI cable to connect the input source to the female HDMI socket on the r ear panel ( b in figure 2 on page 3). The connectors are fully HDCP compliant. With cables up to 25 feet (7.6 m) they support resolutions of up to 1080p @ 60 Hz with 12‑bit color . W ith cables up to 50 feet (15.2 m) they support 1080p o ...

  • Extron electronic HDMI DA2 - page 12

    If the source r equires HDCP encryption and the display is not HDCP compliant, that output channel outputs a green scr een. Both outputs carry +5 VDC and up to 250 mA on pin 18, regulated by a curr ent limiting circuit. W iring for RS-232 Control (Optional) RS‑232 communication between the HDMI DA2 and a host PC can be used to update firmware or ...

  • Extron electronic HDMI DA2 - page 13

    Connecting to the USB Port The mini T ype B USB port is located on the HDMI DA2 front panel ( b in figur e 7 on page 10). It can be used to connect the distribution amplifier to a host computer to update firmware or for configuration using SIS commands. 1. Connect a USB A to mini B cable between the USB Config port on the front panel of the HD ...

  • Extron electronic HDMI DA2 - page 14

    Figure 5. Found New Hardwar e Wizard W elcome Screen z Select Yes, this time only to connect the PC to Windows Update only this one time. z Select Yes, now, and every time I connect a device to automatically connect to Windows Update every time the HDMI DA2 connects to this USB port. z Select No, not this time if you do not want to connect to Windo ...

  • Extron electronic HDMI DA2 - page 15

    5. When the Completed screen appears, click Finish to close the wizar d. NOTE: The wizard appears only on the first occasion you connect the HDMI DA2 to that USB port. The wizard r eappears if you connect the HDMI DA2 to a differ ent USB port or if you connect a differ ent piece of equipment, requiring a differ ent driver , to the same USB port. 6. ...

  • Extron electronic HDMI DA2 - page 16

    Operation This section of the manual provides information on: z HDMI DA2 Front Panel Featur es z EDID Minder HDMI DA2 Fr ont Panel Features HDMI DA2 CONFIG INPUT EDID OUTPUTS 12 SIGNAL HDCP 1 2 4 5 3 Figure 7. HDMI DA2 Front Panel a Power status LED b USB Config port c Signal LEDs d HDCP LEDs e EDID LED Power Status LED The power status LED lights ...

  • Extron electronic HDMI DA2 - page 17

    Signal Status LEDs Input Signal LED The input signal LED lights green when a TMDS signal is detected on the HDMI input. If the source r equires HDCP encryption, this LED may light only after the HDCP has been authenticated. Output Signal LEDs There ar e two output signal LEDs, one for output 1 and the other for output 2. The LEDs light green when a ...

  • Extron electronic HDMI DA2 - page 18

    EDID Minder EDID Minder ensures that the connected sour ce sees the EDID of a display , even if a display is not connected. Depending on the EDID mode selected (by SIS command), the EDID of a connected display can be stored automatically , or the user can manually select from the table of factory loaded EDID files. This EDID is stor ed on an EEPRO ...

  • Extron electronic HDMI DA2 - page 19

    HDMI DA2 Memory Locations X$ Native Resolution Refresh Rate 1 Rate T ype 2 Video Format 3 Audio T ype Pixel Clock X$ Native Resolution Refresh Rate 1 Rate T ype 2 Video Format 3 Audio T ype Pixel Clock 1 Output 1 (default) 30 1360x768 60 Hz PC HDMI 2‑ch 85.5 MHz 2 Output 2 31 1366x768 60 Hz PC HDMI 2‑ch 86 MHz 3 Reserved 32 1440x900 60 Hz PC HD ...

  • Extron electronic HDMI DA2 - page 20

    Footnotes for the EDID table (see page 13) The following footnotes apply to the EDID table on the previous page: 1 Rate T ype z PC: These are primarily VESA standar d computer rates, based on the most commonly used native resolutions. They ar e designed to be used with computer sources. z HDTV : These are video rates standardized by SMPTE and CEA. ...

  • Extron electronic HDMI DA2 - page 21

    SIS Commands This section provides information about the SIS commands that ar e used to configure the HDMIDA2. The following topics are discussed: z Introduction to SIS z Symbols Used in this Guide z Command and Response T able for SIS Commands Intr oduction to SIS The HDMI DA2 accepts SIS commands from a host device such as a computer running ...

  • Extron electronic HDMI DA2 - page 22

    Symbols Used in this Guide When programming in the field, certain characters ar e most conveniently repr esented by their hexadecimal rather than their ASCII values. The table below shows the hexadecimal equivalent of each ASCII character: ASCII to HEX Con version Ta bl e Space . T able 2. ASCII to HEX Conversion T able ] — carriage return with ...

  • Extron electronic HDMI DA2 - page 23

    Command and Response T able for SIS Commands Command ASCII Command (host to unit) Response (unit to host) Additional Description Video Mute Video mute single output X! * X@ B Vmt X! * X@] Video mute output X! (1 or 2) Video mute all outputs X@ B Vmt X@] Video mute all outputs Query Video mute status B Vmt X@ • X@] output 1 status, output 2 status ...

  • Extron electronic HDMI DA2 - page 24

    Command ASCII Command (host to unit) Response (unit to host) Additional Description Other Request part number N 60‑997‑01 ] Query firmware version Q X&] X& = Firmware build (2 decimal places) Reset E ZXXX } Zpx ] HDMIDA2 • SIS Commands 18 ...

  • Extron electronic HDMI DA2 - page 25

    HDMIDA2 • Updating Firmware 19 Updating Firmwar e Updates to the HDMI DA2 firmware ar e released periodically on the Extr on website. Y ou can find which version is currently loaded on your DA using SIS commands. Compar e this with the latest release on the Extr on website and decide whether to update your firmware. TIP: Read the Release No ...

  • Extron electronic HDMI DA2 - page 26

    HDMIDA2 • Updating Firmware 20 Downloading HDMI DA2 Firmwar e T o obtain the latest version of firmware for your HDMI DA2: 1. Visit the Extron website ( www .extron.com ), click the Download link at the top of the page, then click the Firmware link on the left sidebar menu. Figure 9. Firmware Link on the Download T ab 2. On the Download Cente ...

  • Extron electronic HDMI DA2 - page 27

    HDMIDA2 • Updating Firmware 21 Loading the Firmwar e to the HDMI DA2 T o load a new version of firmware to the switcher using Firmwar e Loader , connect the control PC to the HDMI DA2. Y ou may use the front panel USB config port or the r ear panel 3‑pole captive screw Remote port (see Wiring for RS-232 Contr ol on page 6 for information o ...

  • Extron electronic HDMI DA2 - page 28

    HDMIDA2 • Updating Firmware 22 9. On the Open window , navigate to the new firmware file, which has an S19 extension, and double‑click it. Figure 11. Open Window for Firmwar e File Selection A TTENTION: V alid firmware files must have the file extension S19 . A file with any other extension is not a firmware upgrade for this pr oduct ...

  • Extron electronic HDMI DA2 - page 29

    HDMIDA2 • Updating Firmware 23 On the Add Device window , the path to the new firmware file is displayed in the Path field. Figure 12. Path to the New Firmwar e File on the Add Device Window 10. If this is the only device to which you are uploading firmware, click Add . The HDMIDA2 information is added to the Devices section of the Firm ...

  • Extron electronic HDMI DA2 - page 30

    HDMIDA2 • Updating Firmware 24 Figure 13. Firmwar e Loader Screen with a HDMI DA2 Added 11. If you want to remove a device from the Devices section, do the following: 1. Click on the names of the devices to be deleted, to highlight them. 2. Select Remove Selected Device(s) from the Edit menu. 3. On the Remove Device(s) window , select or desel ...

  • Extron electronic HDMI DA2 - page 31

    Mounting Desktop Placement Attach the four provided rubber feet to the bottom of the HDMI DA2 and place it in any convenient location. Rack Mounting UL Guidelines for Rack Mounting The following Underwriters Laboratories (UL) guidelines are r elevant to the safe installation of these products in a rack: 1. Elevated operating ambient temperature — ...

  • Extron electronic HDMI DA2 - page 32

    Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron Asia +65.6383.4400 +65.6383.4664 F AX Extron Japan +81.3.3511.7655 +81.3.3511.7656 F ...

メーカー Extron electronic カテゴリー Musical Instrument Amplifier

Extron electronic HDMI DA2のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- HDMI DA2の取扱説明書
- Extron electronicの製品カード
- パンフレット
- またはExtron electronic HDMI DA2の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Extron electronic HDMI DA2の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Extron electronic HDMI DA2の取り付け説明書、サービスマニュアル、簡易説明書、またはExtron electronic HDMI DA2のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Extron electronic HDMI DA2の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Extron electronic HDMI DA2デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがExtron electronic HDMI DA2を使用するのを助ける技術的文書のことです。説明書は通常、全てのExtron electronic HDMI DA2ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Extron electronicの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Extron electronic HDMI DA2の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははExtron electronic HDMI DA2の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Extron electronic HDMI DA2に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Extron electronic HDMI DA2デバイスの基本機能を使うにあたってのヒント。 Extron electronic HDMI DA2のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Extron electronic HDMI DA2に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるExtron electronic HDMI DA2のメーカー/サービスへの連絡先に関する情報。

Extron electronic HDMI DA2についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもExtron electronic HDMI DA2の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがExtron electronic HDMI DA2で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)