Pelco C2941Mの取扱説明書

24ページ 0.22 mb
ダウンロード

ページに移動 of 24

Summary
  • Pelco C2941M - page 1

    INST ALLA TION C2941M (8/07) IP3701H-2 and IP3701H-2X IP Color Camera ...

  • Pelco C2941M - page 2

    ...

  • Pelco C2941M - page 3

    C2941M (8/07) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description ...

  • Pelco C2941M - page 4

    4 C2941M (8/07) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 7. Only use attachments/accessories specified by t ...

  • Pelco C2941M - page 5

    C2941M (8/07) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This ...

  • Pelco C2941M - page 6

    6 C2941M (8/07) Description The IP3701H-2 and IP3701H-2X are high resolution, color video cameras with a built-in 100Base-TX network interface for live streaming to a standard Web browser (Microsoft ® Internet Explorer ® or Firefox ® ). The camera features open architecture connectivity for third-party software recording solutions and is also En ...

  • Pelco C2941M - page 7

    C2941M (8/07) 7 Basic System Configurations IMPORT ANT NOTE. PLEASE READ . The network implementations in this document are shown as general representations only and are not intended to show detailed network topologies. Y our actual network will differ , requiring changes or perhaps additional network equipment to accommodate the systems as illust ...

  • Pelco C2941M - page 8

    8 C2941M (8/07) Figure 3. Private Network Example Figure 4. Static Network Example IF NOT DHCP , CAMERA CYCLES THROUGH IP ADDRESS RANGE 169.254.200.0 - 169.254.200.255; NETMASK 255.255.0.0 CAMERA CAMERA WEB BROWSER PRIV A TE NETWORK PC ACTS AS SERVER ( ) EXAMPLE 169.254.200.1 ( ) EXAMPLE 169.254.200.0 NETWORK SWITCH NOTE: FOR A SECURE NETWORK, PELC ...

  • Pelco C2941M - page 9

    C2941M (8/07) 9 Camera Layout Figure 5. Camera Layout RESET BUTTON Use the reset button located on the side of the camera to access the following modes: T o access one of these modes: 1. Press and hold the reset button. The unit starts cycling through the modes; hold the button for four seconds to access (cycle through) each mode. The unit status i ...

  • Pelco C2941M - page 10

    10 C2941M (8/07) Installation LENS MOUNTING The camera can use a fixed iris, manual iris or auto iris lens. The camera is factory set for a CS-mount lens, but is easily adjusted for a C-mount lens. 1. C-mount lens only: Completely rotate the back focus adjustment counterclockwise before installing the C-mount lens (refer to Back Focus Adjustment o ...

  • Pelco C2941M - page 11

    C2941M (8/07) 11 Wiring T ables CAT5 CABLE Connect a Cat5 cable to the RJ-45 network connector . The 8-pin connector includes video and PoE for the camera. PoE (IEEE 802.3af) injects power over the same cabling that carries the network data, eliminating the need for a separate power supply . This simplifies the installation and operation of the ca ...

  • Pelco C2941M - page 12

    12 C2941M (8/07) T able C. Recommended Wire Gauge and Wiring Distances The following are the recommended maximum distances for 24 V AC applications and are calculated with a 10-percent voltage drop. (T en percent is generally the maximum allowable voltage drop for AC-powered devices.) Wire Gauge Example: A camera that requires 10 VA and is installe ...

  • Pelco C2941M - page 13

    C2941M (8/07) 13 Lens Setup and Focus Procedures VIDEO DRIVE AUTO IRIS LENS Set the lens mode selector switch to AIV . Switch the ESC and AGC OFF . Refer to the lens instructions and adjust the lens for the optimum picture (video output level of 1 Vp-p). T o focus, completely open the iris by covering the lens with a suitable neutral density (ND*) ...

  • Pelco C2941M - page 14

    14 C2941M (8/07) Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case. T o adjust the back focus: 1. Loosen the two back focus locking screws (one on each side). 2. T urn the back focus ring until the object is in focus. 3. When the back focus adjustment is satisfactory ...

  • Pelco C2941M - page 15

    C2941M (8/07) 15 Switch Settings Figure 8. DIP Switch Default Settings NOTE: Under most conditions, no setting of switches will be required. Please read the details of each switch before making any adjustments.  BLC: Back light compensation. OFF (default setting): Disables the BLC mode. BLC: Enables the BLC mode. If a bright backlight is present ...

  • Pelco C2941M - page 16

    16 C2941M (8/07)  Not Used  EDR: Extended dynamic range • Off (Default setting): Disables the EDR mode. • EDR: Enables the EDR mode to help balance a scene with a large dynamic range. Use this feature to improve the picture in washed-out areas. This feature adds 12X the dynamic range, but also increases dark area picture noise. Refer to D ...

  • Pelco C2941M - page 17

    C2941M (8/07) 17 Dynamic Range and EDR Dynamic range is the ratio between the brightest and darkest parts of an image or scene. A scene that ranges from bright sunlight to deep shadows has a high dynamic range, while indoor scenes with less contrast have a low dynamic range. The EDR (extended dynamic range) feature will help capture the entire rang ...

  • Pelco C2941M - page 18

    18 C2941M (8/07) T roubleshooting Problem Possible Cause Suggested Remedy No video PoE power issue • V erify Cat5 cable connection. • V erify PoE is enabled. • Disconnect the Cat5 cable from the PoE and then reconnect the cable. Power is indicated by the LED. The LED will flash (green) five times per second for approximately two minutes if ...

  • Pelco C2941M - page 19

    C2941M (8/07) 19 Image too light • V erify DIP switch settings. • Use a service connector to verify camera operation. Connect one end of the service connector to the BNC service connector on the camera. Connect the other end of the service connector to a monitor . • Replace camera with a working camera. If the new camera does not work, contac ...

  • Pelco C2941M - page 20

    20 C2941M (8/07) Specifications GENERAL Construction Finish Black polyester powder coat Imaging Device 1/3-inch imager Picture Elements IP3701H-2 768 (H) x 494 (V) IP3701H-2X 752 (H) x 582 (V) Sensing Area 6 mm diagonally Horizontal Resolution 480 TV lines Iris Control Electronic/passive Minimum Illumination 0.5 lux, f/1.2, 40 IRE, AGC on, 75% re? ...

  • Pelco C2941M - page 21

    C2941M (8/07) 21 Minimum Web Browser Requirements PC (Pentium ® 4 microprocessor , 1.6 GHz) with Windows ® 98, Windows 2000, Windows XP (or higher), or Mac ® OS X 10.3.9 (or higher) RAM 512 Mbyte Ethernet Card 100 Mbit Web Browser Internet Explorer 5.5 (or higher) or Firefox 1.5 (or higher) Screen Resolution 1024 x 768 pixels or higher , 16- or ...

  • Pelco C2941M - page 22

    22 C2941M (8/07) The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical and elec ...

  • Pelco C2941M - page 23

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission ...

  • Pelco C2941M - page 24

    Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab Emir ...

メーカー Pelco カテゴリー Security Camera

Pelco C2941Mのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- C2941Mの取扱説明書
- Pelcoの製品カード
- パンフレット
- またはPelco C2941Mの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pelco C2941Mの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pelco C2941Mの取り付け説明書、サービスマニュアル、簡易説明書、またはPelco C2941Mのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pelco C2941Mの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pelco C2941Mデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPelco C2941Mを使用するのを助ける技術的文書のことです。説明書は通常、全てのPelco C2941Mユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pelcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pelco C2941Mの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPelco C2941Mの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pelco C2941Mに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pelco C2941Mデバイスの基本機能を使うにあたってのヒント。 Pelco C2941Mのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pelco C2941Mに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPelco C2941Mのメーカー/サービスへの連絡先に関する情報。

Pelco C2941Mについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPelco C2941Mの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco C2941Mで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)