Honeywell TE821Wの取扱説明書

33ページ 0.85 mb
ダウンロード

ページに移動 of 33

Summary
  • Honeywell TE821W - page 1

    HONEYWELL TE821W SEMI-PROFESSIONAL WEA THER ST A TION USER MANUAL TE821W ...

  • Honeywell TE821W - page 2

    2 T able of Contents Introduction 3 Standard Package Contents 3 Installation 3 Before you begin 3 Thermo-Hygrometer Sensor TS33C 4 Rain Gauge TS906 6 Anemometer (wind sensor) TS805 7 Main Unit 9 Power 10 Buttons and Controls 11 Initial Set up 13 Operation and Window Selection 13 Custom Weather Station Settings 15 LED Backlight Options 24 Time Alarm ...

  • Honeywell TE821W - page 3

    3 Introduction Thank you for selecting the Honeywell Semi-Professional Weather Station. This compact and easy-to-use product uniquely measures and monitors weather data right at your immediate lo cation. It includes a wide range of weather features plus precise atomic time and perpetual calendar . Weather measurements incl ude: air temperature, rel ...

  • Honeywell TE821W - page 4

    4 interconnecting wires are required between the main uni t (receiver) and the remote sensors (transmitters). Power up and test communications between all of the sensors and the main unit BEFORE mounting them outside. • For most applications alkaline batteries are accept able where temperatures remain above 32°F (0°C). • At temperatures below ...

  • Honeywell TE821W - page 5

    5 A. LED INDICATOR • Flashes once when the remote sensor transmits a reading to the main unit. • Flashes twice when battery power is low. B. BATTERY COMPARTMENT Holds two AA-size batteries C. RESET Resets all readings (requires small paper clip.) D. CHANNEL SWITCH Selects the desired sensor channel from 1 to 3 E. WALL-MOUNT RECESSED OPENING Kee ...

  • Honeywell TE821W - page 6

    6 • The remote thermo-hygrometer sensor should be placed in the area with a free air circulation and sheltered from the direct sunlight and an extr eme weather conditions. • Ideally , place the thermo-hygrometer sensor above the natural surfaces (s uch as a grassy lawn). • Avoid placing the thermo-hygrometer sensor near s ources of heat such ...

  • Honeywell TE821W - page 7

    7 Contains battery compartment and rainfall counting electronics E. Battery compartment Holds two AA-size batteries F . Screws Secures battery compartment cover G . Built-in level with bubble Ensures level rain gauge mounting for proper operation H . Bucket see-saw mechanism Collects the rainfall in one of its containers and self-empties once full ...

  • Honeywell TE821W - page 8

    8 • Operating range 100 feet (30 meters) • W all or pole mount A. WIND V ANE Indicates wind direction B. WIND CUPS Measures wind speed C. ANEMOMETER BASE • Holds battery compartment • Allows mounting the anem ometer vertically D. ANEMOMETER ARM Connects battery to the anemometer head assembly . E. WIND CUPS SHAFT Holds wind cups on the anem ...

  • Honeywell TE821W - page 9

    9 H. BA TTER Y COVER Secures battery compartment on the anemometer base Assembly • Slide the wind cups on to the anemomet er rotating shaft. Do not use force. • Insert the longer arm of the Allen Wrench (provided) into the wind cup set screw opening. Feel the head of the set screw inside the wind cups and tighten carefully the set screw securin ...

  • Honeywell TE821W - page 10

    10 Main Unit The main unit measures pressure, indoor te mperature, humidity , and rece ives atomic time data from the US Atomic Clock and outdoor measurements from remote sens ors. It should be placed indoors. FEA TURES Tim e • Precise time and date set via RF signals from US Atomic clock • 12 or 24 hour time format • Manual adjustment of tim ...

  • Honeywell TE821W - page 11

    11 Placement tips • Make sure that the main unit is locating within the operating range of all remote sensors. • Ideally the remote sensors should be mounted wi thin the line of sight of the main unit. • T ransmission range may be affected by trees, me tal structures and electronic appliances. • T est reception before permanently mounting a ...

  • Honeywell TE821W - page 12

    12 Buttons and Controls G F E D C B A H I J K ...

  • Honeywell TE821W - page 13

    13 A. UP - Selects the next availabl e window counter-clockwise - Increases parameters -If pressed and held, activates an atomic time signal search B. DOWN - Selects the next available window clockwise - Decreases parameters -If pressed and held, activates all remote sensors signal search C. SET - Alternates the parameter s for the selected window ...

  • Honeywell TE821W - page 14

    14 Initial Set up 1. Power up each of the remotes as instructed in previous sect ions.( Remove clear protective plastic slips from the battery compartments) 2. Then power up the main display . 3. Once the main unit is powered, the display will briefly show all av ailable LC D segments for a moment. 4. IMPORT ANT : Do not press any buttons during th ...

  • Honeywell TE821W - page 15

    15 2. Time with the City abbreviation 3. Time with the Seconds 4. Month/ Day/ Y ear or Day/ Month/ Y ear . 5. Current UTC T ime (Coordinated Universal T ime) Selecting Clock and Alarm Window Press main unit UP arrow button or DOWN arrow button until the clock icon next to the time/date display continues to flash. Initial Settings: City , T ime, Dat ...

  • Honeywell TE821W - page 16

    16 • Press SET to confirm selection. • Press UP or DOWN to select the correct minute. • Press SET to confirm selection and to complete the in itial programming for your weather station. After programming is completed, the display w ill return to the default Clock and Alar m Window . Note : If you do not complete this sequence your entries wil ...

  • Honeywell TE821W - page 17

    17 Select Pressure and Weather Forecast W indow Press UP or DOWN arrow buttons on the main unit until the weather forecast icon begins to flash, upper display left corner . NOTE: W ait at least 5 - 10 minutes after initial set up to view a pr essure or altitude information. Pressure and Altitude Information Press SET button once (do not hold it) to ...

  • Honeywell TE821W - page 18

    18 • Set the pressure units by pressing the UP or DOWN arro w buttons • Press MEMOR Y button to confirm your selection • Press and hold SET button until the local pressure digits will flash. • Set the sea level pressure by pressing the UP or DOWN buttons to adjust the pressure value. Press and hold UP or DOWN arrow buttons for fast er digit ...

  • Honeywell TE821W - page 19

    19 Previous moon phases are selected with the minus sign select ed: -1 day , -2 days, etc or future moon phase are selected based on the days ahead: +1 day , + 2 days, etc up to 39 days. • After selecting the Pressure and Weather Forecast display , press MEMOR Y button, so “+ 0 days” is flashing. • Press UP or DOWN arrow buttons selecting f ...

  • Honeywell TE821W - page 20

    20 Note: The weather forecast accuracy is approximately 70%. Displa y shows 12 to 24 hour forecas t, not current conditions. The SUNNY icon indicates clear weather, ev en when displayed dur ing the night-time. T emperature and Humidity Window The weather station supports I ndoor T emperature & Humidity and up to five remote temperature and humi ...

  • Honeywell TE821W - page 21

    21 With T emperature and Humidity icon flashing, press the SET button to alternate between “temper ature and relative humidity” or “dew point and relative humidity .” T emperature in Celsius or Fahrenheit With T emperature and Humidity icon flashing, press and hold the SET button to alternate between te mperature in Celsius (ºC) or Fahrenh ...

  • Honeywell TE821W - page 22

    22 rainfall can be displayed in mm or inches. There is a daily rain fall alert that can be programme d in the unit if the daily rain fall exceeds a pre-programmed limit. Selecting Rain Window Press the UP or DOWN arrow buttons on the main unit until the RAIN icon on the display starts flashing. Display: Viewing Rain Statistics With the rain icon fl ...

  • Honeywell TE821W - page 23

    23 Disabling the Daily Rainfall Alert In the Daily Rainfall Alert Mode press the ALARM/CHART button to disable the alert. Wind Window Wind direction is shown by compass point s (i.e. NW) or in bearings starting fr om north (i.e. 22.5º). The unit displays anemometer temperature or wi nd chill, average wind speed (over the past 10 minut es), gust, a ...

  • Honeywell TE821W - page 24

    24 Resetting the Wind Statistics Memory With the wind icon flashing, press and hold MEMOR Y button to reset all wind statistics. Enabling or Disabling the Wind Alerts With the wind icon flashing, press the ALARM/CHART button to recall a current wind s peed, a wind speed alert with the “ ALARM HI” displayed or gust alert with the “GUST ALARM H ...

  • Honeywell TE821W - page 25

    25 Note : Press SET button anytime during alarm programming mode to return to the default clock display . Programming Time Alarms With the Clock and Alarm icon flashing, press the ALARM/CHART button to select the desired alarm. • Press and hold ALARM/CHART button until the hour digit will flash • Set the alarm hour using UP or DOWN arrow button ...

  • Honeywell TE821W - page 26

    26 clock is programmed to search for the at omic time signal daily each hour between 1: 00 am and 4:30 am. Once the time signal has been successfully received, the ti me and date will be updated automatically. T o manually enable or disable the atomic time receiver: • Press and hold UP arrow button - if atomic time reception is activat ed, a tria ...

  • Honeywell TE821W - page 27

    27 Maintenance Changing Batteries The battery status of each weather sensor is checked every hour . If the low battery indicator lights up, replace the batteries in the corresponding unit. Changing Batteries in the Main Unit • First connect the AC/DC adaptor provided to the main unit to avoid losing any data. • Remove the battery compartment do ...

  • Honeywell TE821W - page 28

    28 Thermo-Hygrometer 15 minutes Anemometer (Wind Sensor): 15 minutes Rain Gauge (Rain Sensor) 30 minutes Check or replace the batteries for the corresponding sensor . Then press and hold DOWN arrow button on the main unit to search for all remote signals. If this does not work, check the wireless trans mission path from the corresponding sensor to ...

  • Honeywell TE821W - page 29

    29 ...

  • Honeywell TE821W - page 30

    30 Specifications Radio Frequency : 433 MHz RF Reception range : 100-328 feet (30 -100 m) Barometric Pressure Measuring Range: 14.75 inHg to 32.44 inHg ( 500 Hpa to 1 100Hpa); (374.5 mmHg to 823.8 mmHg) Resolution: 0.003 inHg (0.1 Hpa, 0.08 mmHg) Accuracy: 0.015 inHg (0.5 Hpa; 0.38 mmHg) Sampling interval: 20 minutes Sea level Altit ude Compensatio ...

  • Honeywell TE821W - page 31

    31 T ransmitting Interval: around 47 seconds Operating range: 328 feet (100 m) Wind Direction Range: 0° to 360° Resolution: 22.5° Accuracy: 1 1.25° Starting Threshold: 3mph (4.8 Km/h) T ransmitting interval: 33 seconds Operating Range: 100 feet (30 m) Wind Speed Range: 0 to 100 mph ( 160 Km/h, 86.897 Knots) Resolution: 0.1mph (0.16 Km/h) Accura ...

  • Honeywell TE821W - page 32

    32 Anemometer: 2 years Rain Gauge: 2 years Weight (without batteries) Main unit: 8.15oz (231g) Remote Thermo-Hygrometer: 2.29oz (65g) Remote Anemometer: 11.12oz (315g) Remote Rain gauge: 10.24oz (290g) Dimensions Main unit: 7.31 (L) x 5.39 (H) x 1.26 (D) inches / 185.8 (L) x 136.9 (H) x 32 (D) mm Remote Thermo - Hygrometer: 2.37 (L) x 4 (H ) x 1 (D ...

  • Honeywell TE821W - page 33

    33 DECLARA TION OF CONFORMITY Name: Meade Instruments Corp. Address: 27 Hubble, Irvine, CA 92618 T elephone No.: 1-949-451-1450 declare that the product Product No.: TE821W Product Name: Semi-Professional Weather Station Manufacturer: Hideki Electronics Ltd. Address: Unit 2304-06, 23/F Riley House, 88 Lei Mu k Road, Kwai Chung, New T erritories, Ho ...

メーカー Honeywell カテゴリー Marine Radio

Honeywell TE821Wのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TE821Wの取扱説明書
- Honeywellの製品カード
- パンフレット
- またはHoneywell TE821Wの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Honeywell TE821Wの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Honeywell TE821Wの取り付け説明書、サービスマニュアル、簡易説明書、またはHoneywell TE821Wのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Honeywell TE821Wの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Honeywell TE821Wデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHoneywell TE821Wを使用するのを助ける技術的文書のことです。説明書は通常、全てのHoneywell TE821Wユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Honeywellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Honeywell TE821Wの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHoneywell TE821Wの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Honeywell TE821Wに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Honeywell TE821Wデバイスの基本機能を使うにあたってのヒント。 Honeywell TE821Wのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Honeywell TE821Wに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHoneywell TE821Wのメーカー/サービスへの連絡先に関する情報。

Honeywell TE821Wについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHoneywell TE821Wの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHoneywell TE821Wで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)