Snapper ELT180H33IBVの取扱説明書

40ページ 1.28 mb
ダウンロード

ページに移動 of 40

Summary
  • Snapper ELT180H33IBV - page 1

    Safety Instructions & Operator’s Manual for EUROPEAN LAWN TRACTOR HYDROSTATIC DRIVE SERIES I MODEL ELT180H33IBV MODEL NUMBER EXPLANATION E LT 180 H 33 I B V EUROPEAN MODEL MODEL DESIGNATION ENGINE HP * ENGINE TYPE DRIVE SYSTEM TYPE ENGINE MODEL CUTTING WIDTH SERIES DESIGNATION E – European Model 33 – 33” Cutting Width Mow er LT – Law ...

  • Snapper ELT180H33IBV - page 2

    2 IMPORTANT SAFETY INSTRUCTIONS WARNING: This pow erful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply w ith the follow ing SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these in ...

  • Snapper ELT180H33IBV - page 3

    3 IMPORTANT SAFETY INSTRUCTIONS PREPARATION (Continued From Previous Page) 7. Keep people and pets out of mow ing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area. 8. Check shields, deflectors, sw itches, blade controls and other safety dev ices frequently for proper operation and location. 9. Make sure all saf ...

  • Snapper ELT180H33IBV - page 4

    4 IMPORTANT SAFETY INSTRUCTIONS TOWING 1. Tow only with a machine that has a hitch designed for tow ing. DO NOT attach tow ed equipment except at the hitch point. 2. Follow the manufacturer’s recommendation for w eight limits for tow ed equipment and tow ing on slopes. 3. DO NOT allow children or others on tow ed equipment. 4. On slopes, the w ei ...

  • Snapper ELT180H33IBV - page 5

    5 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ........... 2-4 TABLE OF CONTENTS ......................................... 5 SECTION 1 - FAMILIARIZATION ...................... 6-8 Compone nts ....................................................... 6 Controls ................................................................ 6 Decals / Sy mbols ... ...

  • Snapper ELT180H33IBV - page 6

    6 Section 1 - FAMILIARIZATION FIGURE 1.1 COMPONENTS The nomenclature drawings above, illustrate the essential components of the SNAPPER Lawn Tractor. It is recommended that all operators of this equipment become thoroughly familiar with the components and their operation BEFORE OPERATING. Specific details involving the engine are found in the separ ...

  • Snapper ELT180H33IBV - page 7

    7 Section 1 - FAMILIARIZATION – DECALS / SYMBOLS All operators should locate, read and understand all decals on the machine before attempting any operation of the machine. If any operator has difficulty in understanding certain symbols incorporated in the decals, an authorized SNAPPER dealer should be contacted for explanation. ROLL RELEASE DECA ...

  • Snapper ELT180H33IBV - page 8

    8 Section 1 - FAMILIARIZATION – DECALS / SYMBOLS SAFETY INSTRUCTIONS. OPERA TING INSTRUCTIONS. CONTROL IDENTIFICATION – 7-2754 FORWARD REVERSE NEUTRAL DIRECTION A ND SPEED CONTROL 7-3424 HEIGHT OF CUT DECAL 4-6218 LOWEST HEIGHT OF CUT HIGHEST HEIGHT OF CUT CONSOLE DECAL 7-3579 RABBIT ”FA ST” TURTLE “SLOW” CHOKE ENGINE “OFF” START EN ...

  • Snapper ELT180H33IBV - page 9

    9 Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECKLIST Make the following checks and perform service as required before each start-up. 2.1.1. Check tires and add air as needed to bring pressure to 12 P.S.I. in front tires and 12 P.S.I. in rear tires. 2.1.2. Check guards, deflectors and covers to make sure all are in place and securely tighten ...

  • Snapper ELT180H33IBV - page 10

    10 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. STARTING ENGINE 1. Take a comfortable position in seat of machine, look around to make sure that the area you are going to mow is clear of people, children and pets. Take note of any stationary obstacles! NOTE: The interlock system will prevent the engine from starting if the ...

  • Snapper ELT180H33IBV - page 11

    11 Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION (continued) 2.3.2. STARTING WHEEL DRIVE 1. Shift speed control lever to neutral. 2. Start engine. Refer to Section “STARTING ENGINE”. 3. Release clutch/brake pedal. 4. Slowly shift speed control lever forward for forward motion or to the rear for reverse motion. See Figure 2.7. ...

  • Snapper ELT180H33IBV - page 12

    12 Section 2 - OPERATING INSTRUCTIONS 2.4 STOPPING 2.4.3. STOPPING MOWER BLADE 1. Stop mower blade by moving blade engagement lever to the "OFF" position. See Figure 2.11. FIGURE 2.11 WARNING Once blade is disengaged, it should come to a complete stop in 5 seconds or less. If the blade continues to rotate after 5 seconds, the blade brake ...

  • Snapper ELT180H33IBV - page 13

    13 Section 2 - OPERATING INSTRUCTIONS 2.6. ROLLING TRACTOR WITH ENGINE OFF Rolling Hydro Models 1. With engine "OFF", move to rear of tractor. 2. Pull the roll release control all the way out to disengage the hydro transmission. See Figure 2.15. FIGURE 2.15 3. Move tractor to desired location. 4. Push roll release control all the way in t ...

  • Snapper ELT180H33IBV - page 14

    14 Section 2 - OPERATING INSTRUCTIONS 2.7. REVERSE LOCKOUT MECHANISM Data indicates that tragi c back-over accidents occur each year. These accidents usually involve unsupervised children. Many times these children have been given rides on the machine and have been trained to view this potentially danger ous piece of machinery as fun rather than be ...

  • Snapper ELT180H33IBV - page 15

    15 Section 3 - MAINTENANCE 3.1 INTRODUCTION To retain the quality of the Tractor, use genuine SNAPPER replacement parts only. Contact a loca l SNAPPER dealer for parts and service assistance. For the correct part or information for a particular Tractor, al w a y s m e n ti o n the model and serial number. SNAPPER recommends returning the Tractor to ...

  • Snapper ELT180H33IBV - page 16

    16 Section 3 - MAINTENANCE 3.2.4. CHECK DECK DRIVE BELT 1. With engine "OFF", move blade engagement lever to "ON". 2. Measure blade cable extension spring. Spring should extend 1" +/-1/8" fo r proper belt tension. See Figure 3.3. FIGURE 3.3 3. To adjust tension, Refer to Section “BLADE BELT ADJUSTMENT”. 3.3 SERVICE ...

  • Snapper ELT180H33IBV - page 17

    17 Section 3 - MAINTENANCE 3.3.4. TRACTOR LUBRICATION 1. Front Wheel Bearings Lubricate each front wheel bearing through the grease fitting on wheel hub. Using general purpose grease in a grease gun, add grease until grease purges from bearing. See Figure 3.6. FIGURE 3.6 2. Axle Spindles Lubricate each axle spindle with 1 to 3 shots of general purp ...

  • Snapper ELT180H33IBV - page 18

    18 Section 3 - MAINTENANCE 3.3.4. TRACTOR LUBRICATION (Continued From Previous Page) 7. Steering Tie Rod Lubricate both ends of steering tie rod with a small amount of 30 wt. motor oil from an oil can. See Figure 3.10. FIGURE 3.10 8. Blade Engagement Mechanism Using 30 wt. motor oil, lubricate the blade engagement mechanism pivot points, which are ...

  • Snapper ELT180H33IBV - page 19

    19 Section 3 - MAINTENANCE 3.4 ANNUALLY (END OF EACH SEASON) 3.4.2. FUEL FILTER (Continued From Previous Page) 3. Install new fuel filter part number 1-4359. See Figure 3.14. FIGURE 3.14 4. Fill fuel tank with fresh gasoline. Refer to engine owner's manual for fuel specifications. 3.4.3. SPARK PLUG Remove and replace engine spark plug. Refer t ...

  • Snapper ELT180H33IBV - page 20

    20 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug. Engine and components can be extremely hot. Av oid burns by allowing engine and compo ...

  • Snapper ELT180H33IBV - page 21

    21 Section 4 - ADJUSTMENT & REPAIR 4.2.2. BLADE BELT ADJUSTMENT – 33” Deck (Continued from previous page) IMPORTANT: If deck front to rear level is not correct, this could cause blade belt problems. 6. Move blade engagement lever to "ON". 7. Measure blade cable extension spring. Spring should extend 1" +/-1/8" for proper ...

  • Snapper ELT180H33IBV - page 22

    22 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug. Engine and components can be extremely hot. Av oid burns by allowing engine and compo ...

  • Snapper ELT180H33IBV - page 23

    23 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug. Engine and components can be extremely hot. Av oid burns by allowing engine and compo ...

  • Snapper ELT180H33IBV - page 24

    24 Section 4 - ADJUSTMENT & REPAIR 4.3 TRACTOR DRIVE COMPONENTS 4.3.1. BRAKE ADJUSTMENT 1. To be properly adjusted, the brake should stop the tractor in approximately 6 feet from top speed when the clutch/brake pedal is fully depressed. 2. Adjust brake when necessary as follows: 3. Turn engine “OFF”. Remove key. 4. Locate brake adjustment n ...

  • Snapper ELT180H33IBV - page 25

    25 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key . Remove spark plug w ire from spark plug and secure w ire aw ay from spark plug. Engine and components can be extremely hot. Av oid burns by allowing engine and compo ...

  • Snapper ELT180H33IBV - page 26

    26 Section 4 - ADJUSTMENT & REPAIR 4.4.2. (NINJA) BL ADE WEAR LIMITS The ninja recycling blade requires more frequent service intervals than standard blades. Check for excessive wear and damage before each use. See Figure 4.18. FIGURE 4.18 4.4.3. (STANDARD) BLADE SHARPENING Blades should be kept sharp at all times. When the blades are dull, cut ...

  • Snapper ELT180H33IBV - page 27

    27 Section 4 - ADJUSTMENT & REPAIR 4.4.5. 33" MOWER BLADE REPLACEMENT (Continued) 6. Install new blade, part number 3-4168, onto blade mounting bar. 7. Torque blade to 30 to 40 ft lbs. of torque. 4.4.6 TRACTION DRIVE BELT REPLACEMENT It is necessary to remove deck in order to replace belts. Remove deck as follows: 1. Place tractor on a fir ...

  • Snapper ELT180H33IBV - page 28

    28 Section 4 - ADJUSTMENT & REPAIR Traction drive belt removal (Continued from previous page) 2. Slide belt guide assembly to the rear and remove. 3. Disconnect traction belt idler pulley spring from tractor frame. See Figure 4.26. FIGURE 4.26 WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP ...

  • Snapper ELT180H33IBV - page 29

    29 Section 4 - ADJUSTMENT & REPAIR Traction drive belt replacement (Continued from previous page) NOTE: When installing a new belt, make certain the stationary idler is mounted in the hole closest to the L.H. side of the tractor. See Figure 4.29. 4. Make certain belt is within belt guides of idlers. 5. Attach tension idler spring to tractor fra ...

  • Snapper ELT180H33IBV - page 30

    30 Section 4 - ADJUSTMENT & REPAIR 4.5 BATTERY 4.5.1. BATTERY REMOVAL 1. Raise operator's seat. 2. Remove the two adjusting knobs. 3. Remove seat assembly and move forward. Use care not to disconnect wires from seat switch. See Figure 4.33. FIGURE 4.33 4. Remove negative ( - ) cable first. 5. Remove positive ( + ) cable last. 6. Remove bat ...

  • Snapper ELT180H33IBV - page 31

    31 Section 4 - ADJUSTMENT & REPAIR WARNING DO NOT OVERFILL! DO NOT attempt to service or charge the battery while it is installed on the machine. DO NOT use “BOOST” chargers on the battery. 4.5.5. BATTERY TESTING There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the ...

  • Snapper ELT180H33IBV - page 32

    32 Section 4 - ADJUSTMENT & REPAIR AVAILABLE ACCESSORIES The SNAPPER Series H LAWN TRACTOR can be equipped with a va riety of accessories that increase its versatility. The accessories available for each model are listed in the chart below. Contact an authorized SNAPPER dealer for ordering any of the accessories desired. AVAILABLE ACCESSORIES E ...

  • Snapper ELT180H33IBV - page 33

    33 SECTION 5 - ELECTRICAL SYSTEM Figure 5.1 illustrates typical harness routing on some Snapper Lawn Tractors. Use this when locating various electrical components. FIGURE 5.1 TO BATTERY NEGATIVE (-) TERMINAL TO BATTERY POSITIVE (+) TERMINAL SOLENOID (UNDER SEAT) SEAT SWITCH IGNITION SWITCH HEADLIGHT SWITCH 20 A MP FUSE PARK BRAKE SWITCH TO R.H. HE ...

  • Snapper ELT180H33IBV - page 34

    34 SECTION 5 - ELECTRICAL SYSTEM SCHEMATICS BRIGGS & STRATTON WITH LIGHTS FIGURE 5.2 ...

  • Snapper ELT180H33IBV - page 35

    35 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Starter Will Not Crank Engine 1. Battery dead. 1. Service battery. 2. Blown fuse. 2. Replace fuse. 3. Electrical connections l oose or corroded. 3. Clean and check connections for good contact. 4. Defective ignition switch. 4. Contact authorized SNAPPER dealer. 5. Starter Spins witho ...

  • Snapper ELT180H33IBV - page 36

    36 TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Tractor Will Not Move Or Loss Of Traction 1. Speed control handle in the neutral “N” position. 1. Place speed control in desired speed. 2. Roll release control in “ROLL” position. (Hydro Models Only) 2. Move roll release control to the engaged position. 3. Low transmission oi ...

  • Snapper ELT180H33IBV - page 37

    37 MAINTENANCE SCHEDULE SUBJECT SERVICE TO BE PERFORMED REFERENCE PAGES EACH USE 5 HOURS 25 HOURS 50 HOURS 100 HOURS EACH SEASON Engine Check Oil Level Page 9 X Engine Initial Oil Change Page 15 X Engine Periodic Oil Change Page 16 X* Air Pre-Cleaner Service Pre-Cleaner Element Engine Manual & Page 16 X** Air Cleaner Replace Element Engine Manu ...

  • Snapper ELT180H33IBV - page 38

    38 2 YEAR LIMITED WARRANTY For two (2) years from purchase date for the orig inal purchaser's residential, non-commercial use, SNAPPER , through any authorized SNAPPER dealer will replace, free of charge (except fo r taxes where applicable), any part or parts found upon examination by the factory at Mc Donough, Georgia, to be defective in mate ...

  • Snapper ELT180H33IBV - page 39

    39 SERVICE NOTES ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ ___________________________________________________________________ _____________________________________________________________ ...

  • Snapper ELT180H33IBV - page 40

    40 Safety Instructions & Operator’s Manual for EUROPEAN LAWN TRACTOR HYDROSTATIC DRIVE SERIES I IMPORTANT Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contai n very important emissions information and critical safety warnings. Read, Und ...

メーカー Snapper カテゴリー Lawn Mower

Snapper ELT180H33IBVのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ELT180H33IBVの取扱説明書
- Snapperの製品カード
- パンフレット
- またはSnapper ELT180H33IBVの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Snapper ELT180H33IBVの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Snapper ELT180H33IBVの取り付け説明書、サービスマニュアル、簡易説明書、またはSnapper ELT180H33IBVのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Snapper ELT180H33IBVの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Snapper ELT180H33IBVデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSnapper ELT180H33IBVを使用するのを助ける技術的文書のことです。説明書は通常、全てのSnapper ELT180H33IBVユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Snapperの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Snapper ELT180H33IBVの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSnapper ELT180H33IBVの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Snapper ELT180H33IBVに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Snapper ELT180H33IBVデバイスの基本機能を使うにあたってのヒント。 Snapper ELT180H33IBVのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Snapper ELT180H33IBVに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSnapper ELT180H33IBVのメーカー/サービスへの連絡先に関する情報。

Snapper ELT180H33IBVについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSnapper ELT180H33IBVの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper ELT180H33IBVで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)