Pelco IS150の取扱説明書

12ページ 0.84 mb
ダウンロード

ページに移動 of 12

Summary
  • Pelco IS150 - page 1

    Addendum IS90/IS110/IS150 Series Camclosure ® C3438M (5/07) ...

  • Pelco IS150 - page 2

    2 C3438M (5/07) Introduction This addendum updates the camera adjustment sections in the IS90, IS110, and IS1 50 Series Camclosure ® Installation manuals. • IS90 (C3425M) – DN/CH/C Series Adjustments (pages 18-20) – DW/CW Series Adjustments (pages 21-23) • IS110 (C3426M) – DN/CH Series Adjustments (pages 18-20) – DW/CW Series Adjustmen ...

  • Pelco IS150 - page 3

    C3438M (5/0 7) 3 DN/CH/C Series Adjustments Refer to Figure 1 to adjust IS90-DN/CH/C models. Refer to Figure 2 to adjust IS110-DN/CH or IS150-DN/CH models. Figur e 1. Adjusting an IS90-DN/CH/C Series Camclosure Figure 2. Adjusting an IS110-DN/CH or IS150-DN-CH Series Camclosure ...

  • Pelco IS150 - page 4

    4 C3438M (5/07) SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: AGC (Auto Gain Control) The AGC (automatic gain control) adjusts the image automatically to compensate for changes in light levels. Set to ON to enable AG C. Set to O FF to disable AGC. The default is ON. SW4-2: BLC (Backlight Compensation) Th ...

  • Pelco IS150 - page 5

    C3438M (5/0 7) 5 AUTO IRIS LEVEL ADJUSTMENT T o adjust the auto iris DC-drive level (refer to Figure 1 or Figure 2 on page 3): 1. T ilt or rotate the camera module until you can access the auto iris level control (R19). 2. T urn the screw clockwise to increase the brig htness level or counterclockwise to decrease the brightness level. V ERTICAL PHA ...

  • Pelco IS150 - page 6

    6 C3438M (5/07) T o manually correct defective pixels (r efer to Figure 1 or Figure 2 on page 3): 1. Cover the lens completely . Make sure no light can enter the lens. NOTE: The mechanical iris lens aperture does not completely block the light. 2. Press and hold button SW3 for one second. The came ra will find and correct defective pixels. NOTE: An ...

  • Pelco IS150 - page 7

    C3438M (5/0 7) 7 DW/CW Series (Wide Dy namic Range) Adjustments Refer to Figure 4 to adjust IS90-DW/CW models. Refer to Figure 5 to adjust IS110-DW/CW or IS150-DW/CW models. Figure 4. Adjusting an IS9 0-DW/CW Series Camclosure Figure 5. Adjusting an IS110-DW/CW or IS150-DW/CW Series Camclosure R7 R7 ...

  • Pelco IS150 - page 8

    8 C3438M (5/07) SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW1-1: Video Format Set to ON for NTSC. Set to OFF for PAL. The default is ON. SW1-2: Line Sync When multiple cameras are connected to the same sw itching device, vertical roll may occur on the monitor . AC line lock eliminates ve rtical roll by lock ...

  • Pelco IS150 - page 9

    C3438M (5/0 7) 9 SW1-7: DSS (Digital Slow Shutter) The default shutter speed for NTSC is 30 frames per sec ond (fps). It is 25 fps for P AL. This is also known as SENS 2X. Y ou can decrease the shutter speed to 7.5 fps (NTSC) or 6.25 fps (P AL). This is known as SENS 8X, which improves low light sensitivity . Set to ON to select SENS 2X. Set to OFF ...

  • Pelco IS150 - page 10

    10 C3438M (5/07) AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS90-DW and IS90-CW Series Ca mclosure s automatically adjust the camera to the auto iris. Au to iris level adjustments are not necessary . V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only . When using more than one camera power supply , a br ief vertic ...

  • Pelco IS150 - page 11

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warrant y are as noted bel ow: • Five years on fiber o ptic products and TW3 000 Series unshield ed twisted pair tr ...

  • Pelco IS150 - page 12

    Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab E ...

メーカー Pelco カテゴリー Home Security System

Pelco IS150のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- IS150の取扱説明書
- Pelcoの製品カード
- パンフレット
- またはPelco IS150の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pelco IS150の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pelco IS150の取り付け説明書、サービスマニュアル、簡易説明書、またはPelco IS150のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pelco IS150の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pelco IS150デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPelco IS150を使用するのを助ける技術的文書のことです。説明書は通常、全てのPelco IS150ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pelcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pelco IS150の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPelco IS150の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pelco IS150に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pelco IS150デバイスの基本機能を使うにあたってのヒント。 Pelco IS150のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pelco IS150に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPelco IS150のメーカー/サービスへの連絡先に関する情報。

Pelco IS150についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPelco IS150の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco IS150で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)