日本語 dropdown-ico

Life Fitness 849の取扱説明書

35ページ 2.26 mb
ダウンロード

ページに移動 of 35

Summary
  • Life Fitness 849 - page 1

    8500 3-ST ACK MUL TI-GYM Part # 6965401 8500104 Rev . C Revision: 08/29/01 1 ASSEMBL Y INSTRUCTIONS ...

  • Life Fitness 849 - page 2

    IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8500 MULTI-GYM. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Rubber mallet or hammer * 3/4” wrench, 9/16” wrench * Ratch ...

  • Life Fitness 849 - page 3

    3 PA R T # 6617103 6779802 6625502 6624202 6624302 6622903 6623003 6623503 6624502 6622503 6620903 6691803 6692402 6623702 6662203 6662303 6628302 6275302 6523401 6765203 6765303 6769903 6768003 6767903 6769003 6769702 6769803 6772102 6768803 6768503 6769203 6965503 6872502 6771003 6770102 6871702 6768303 6770703 6772201 6772301 6764901 6773101 696 ...

  • Life Fitness 849 - page 4

    4 STEP 1: FIGURE 1 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble the LEG WEIGHT STACK BASE (23) and the PRESS WEIGHT STACK BASE (24) to the BASE (25) using two 1/2 X 3-1/4” BOLTS (95) and two 1/2” LOCK NUTS (85) as shown in FIGURE 1. • Apply two NON-SKID STRIPS (61) to the BASE (25) as shown in FIGURE 1. 1/2 X 3-1/4” 95 24 25 85 ...

  • Life Fitness 849 - page 5

    STEP 2: FIGURE 2 5 • LOOSELY assemble the FRONT UPRIGHT (29) to the BASE (25) using two 1/2 X 3-1/4” BOLTS (95) and two 1/2” LOCK NUTS (85) as shown in FIGURE 2. • LOOSELY assemble the REAR UPRIGHT (1) to the BASE (25) using one 1/2 X 3” BOLT (94), two 1/2” WASHERS (84), and one 1/2” LOCK NUT (85) as shown in FIGURE 2. • LOOSELY ass ...

  • Life Fitness 849 - page 6

    STEP 3: FIGURE 3 6 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the FLOATING PULLEY STOP (11) and the SEAT SUPPORT (12) to the FRONT UPRIGHT (29) using two 1/2 X 4” BOLTS (96) and two 1/2” LOW HEIGHT LOCK NUTS (86) as shown in FIGURE 3. • SECURELY assemble one 3/8 X 2-3/4” SPRING PIN (62) to the SEAT SUPPORT (12) as shown in F ...

  • Life Fitness 849 - page 7

    7 STEP 4: FIGURE 4 • SECURELY assemble the BEARING HOUSING (10) and the CENTER PULLEY BRACKET (27) to the FRONT UPRIGHT (29) using two 1/2 X 4” BOLTS (96) and two 1/2” LOW HEIGHT LOCK NUTS (86). • SECURELY assemble a 3/8 X 2-3/4” SPRING PIN (62) to the to the RIGHT & LEFT PEC ARM (6 & 7). See FIGURE 4. • Assemble the RIGHT PEC A ...

  • Life Fitness 849 - page 8

    STEP 5: 8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble one 3/8 X 2-3/4” SPRING PIN (62) to the WOLFF SLEEVE (14) as shown in FIGURE 5. FIGURE 5 • Assemble one U-PIN (52) to the WOLFF SLEEVE (14) using one 1/2” PAL NUT (73). • Slide one 4” VINYL SLEEVE (59) onto the U-PIN (52) as shown in FIGURE 5. • CAREFULLY slide the WOL ...

  • Life Fitness 849 - page 9

    9 STEP 6: FIGURE 6 • SECURELY assemble the PRESS BASE (38) to the BASE (25) using two 1/2 X 3” BOLTS (94), two 1/2” WASHERS (84), and two 1/2” LOCK NUTS (85), and to the REAR UPRIGHT (1) using one 1/2 X 3” BOLT (94), one 1/2” WASHER (84), and one 1/2” LOCK NUT (85) as shown in FIGURE 6. • Assemble the SWIVEL PULLEY BRACKET (35) to t ...

  • Life Fitness 849 - page 10

    STEP 7: FIGURE 7 10 • SECUREL Y assemble the PRESS FRAME (37) to the PRESS BASE (38) using one 1/2” X 3” BOL T (94), two 3/8 X 3” COUNTERSUNK BOL TS (1 15), one 4-1/2” X 8” PLA TE (57), two 1/2” W ASHERS (84), two 3/8” W ASHERS (80), one 1/2” LOCK NUT (85), and two 3/8” LOCK NUTS (82). (NOTE: Make sure 3/8” countersunk bolts a ...

  • Life Fitness 849 - page 11

    STEP 8: FIGURE 8 11 • Slide two HINGE TABS (76) onto the WOLFF SLEEVE (14) and SECURELY attach PRESS SEAT PAD (100) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). (NOTE: The “hinge” part of the HINGE TAB (76) should face upward as shown in FIGURE 8.) • Slide the RIGHT BACK PAD ANGLE (5) and LEFT BACK PAD ANGLE (4) onto the ...

  • Life Fitness 849 - page 12

    12 STEP 9: FIGURE 9 • LOOSELY assemble the PRESS ARM ADJUST (36) to the REAR UPRIGHT (1) using two 1” PILLOW BLOCK BEARINGS (49), four 3/8 X 3-1/4” BOLTS (91), four 3/8” WASHERS (80), and four 3/8” LOCK NUTS (82). (NOTE: Assemble PILLOW BLOCKS (49) so the set screws are on the outside, this will allow more adjustment.) See FIGURE 9. • A ...

  • Life Fitness 849 - page 13

    STEP 10: 13 • SECURELY assemble one 1/2 X 3-1/2” SPRING PIN (63) to the PRESS ARM (8) as shown in FIGURE 10. FIGURE 10 • SECURELY assemble the PRESS ARM (8) to the PRESS ARM ADJUST (36) using one 1/2 X 7-1/2” BOLT (98), two 1/2” WASHERS (84), two 1/2” FLANGE BEARINGS (70), and one 1/2” LOW HEIGHT LOCK NUT (86). (NOTE: SECURELY tighten ...

  • Life Fitness 849 - page 14

    STEP 11: FIGURE 11 14 • SECURELY assemble the REAR BASE LEG (31) to the LEG FRAME (34) using two 1/2 X 3” BOLTS (94), two 1/2” WASHERS (84), and two 1/2” LOCK NUTS (85) as shown in FIGURE 11. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 12: FIGURE 12 • SECURELY assemble the LEFT & RIGHT LEG EXTENSION HANDLES (16 & 15) to the LEG FRAM ...

  • Life Fitness 849 - page 15

    STEP 13: FIGURE 13 15 • SECURELY assemble one 2 X 8” PLATE (17) to the LEG SEAT PAD (102) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). See FIGURE 13. STEP 14: • SECURELY assemble the LEG SEAT PAD (102) to the HINGE TABS (76) using two 3/8 X 1-1/4” BOLTS (88) and two 3/8” WASHERS (80). See FIGURE 14. FIGURE 14 80 17 102 ...

  • Life Fitness 849 - page 16

    16 STEP 15: FIGURE 15 • Assemble LEG BACK PAD ADJUST (2) and LEG BACK PAD SUPPORT (3) to the LEG FRAME (34) using one 1/2 X 6-1/2” BOLT (97), two 1/2” FLANGE BEARINGS (70), one 1/2” LOCK NUT (85) as shown in FIGURE 15. (NOTE: Securely tighten, then back nut off 1/4 turn to allow the two parts to rotate freely.) 0 1 2 34 5 6 1/2 1/2 1/2 1/2 ...

  • Life Fitness 849 - page 17

    STEP 16: 17 FIGURE 16 • SECURELY assemble the LEG BACK PAD (103) to the LEG BACK PAD ADJUST (2) and the LEG BACK PAD SUPPORT (3) using four 3/8 X 3-1/4” BOLTS (91) and four 3/8” WASHERS (80). See FIGURE 16. • SECURELY assemble two 4 X 7” ROLLER PADS (41) to the LEG FRAME (34) using one 19-1/4” TUBE (39) and two 1-5/16” SHAFT COLLARS ( ...

  • Life Fitness 849 - page 18

    18 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 17: FIGURE 17 • SECURELY assemble two 3/8 X 2-3/4” SPRING PINS (62) to the PAD SLEEVES (33) as shown in FIGURE 17. • Assemble four ROLLER PADS (41) to the PAD SLEEVES (33) using four 1-5/16” SHAFT COLLARS (79). SECURELY tighten set screws on SHAFT COLLARS (79). See FIGURE 16. • Slide P AD SLEEV ...

  • Life Fitness 849 - page 19

    STEP 19: 19 FIGURE 19 • Insert the two GUIDE RODS (19) into the BASE (25) as shown in FIGURE 19. Lubricate the GUIDE RODS (19) with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (47) down over the GUIDE RODS (19). See FIGURE 19. • Using EXTREME CARE slide twenty WEIGHT PLATES (106) down ...

  • Life Fitness 849 - page 20

    STEP 20: FIGURE 20 20 • Slide the PRESS GUIDE ROD SUPPORT (20) and LEG GUIDE ROD SUPPORT (21) over their respective GUIDE RODS (19) and SECURELY assemble them to the TOP BOOM (30) using two 1/2 X 3-1/4” BOLTS (91) and two 1/2” LOCK NUTS (85) as shown in FIGURE 20. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 21: FIGURE 21 • Slide the 13/16” ...

  • Life Fitness 849 - page 21

    21 46 44 45 42 43 ...

  • Life Fitness 849 - page 22

    22 STEP 22: FIGURE 22 • SECUREL Y assemble two 4-1/2” PULLEYS (48) into the slots of the T OP BOOM (30) using two 3/8 X 2-3/4” BOL TS (90), four 3/8” FLANGE SP ACERS (69), two 2-7/8” X 2-1/4” CABLE CLIPS (1 16) and two 3/8” LOCK NUTS (82). (NOTE: Loop the cable around each pulley prior to inserting it in the the slot.) 0 1 2 34 5 6 1/ ...

  • Life Fitness 849 - page 23

    23 STEP 26: STEP 25: FIGURE 25 • Route the LA T CABLE (42) around the pulley in FLOA TING PULLEY STOP (1 1) and the FLOA TING PULLEY BRACKET (55) as shown in FIGURE 25. (NOTE: The CABLE CLIPS may need to be loosened.) • SECURELY assemble two 4-1/2” PULLEYS (48) into the slots of the BASE (25) using two 3/8 X 2-3/4” BOLTS (90), four 3/8” F ...

  • Life Fitness 849 - page 24

    24 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 27: FIGURE 27 FIGURE 28 STEP 28: • LOOSELY assemble two 4-1/2” PULLEYS (48) to the CENTER PULLEY BRACKET (27) using two 3/8 X 2” BOLTS (89), two 2-7/8” CABLE CLIPS (67), two 3/8” WASHERS (80), and two 3/8” LOCK NUTS (82). See FIGURE 28. • Screw the threaded end of the LAT CABLE (42) approxi ...

  • Life Fitness 849 - page 25

    STEP 29: 25 FIGURE 29 • Assemble one 4-1/2” PULLEY (48) around the PEC DEC CABLE (46) and to the PULLEY BRACKET (26) using one 3/8 X 2” BOL T (89) , two 2-7/8 X 1” CABLE CLIPS (67) and one 3/8” LOCKNUT (82) as shown in FIGURE 29. STEP 30: FIGURE 30 3/8 X 2” 89 48 46 PEC CABLE 82 • Slide the ends of the PEC DEC CABLE (46) into the bush ...

  • Life Fitness 849 - page 26

    26 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 32: FIGURE 32 • Screw the threaded end of AB CABLE (45) approximately 1” into the end of the PULLEY BRACKET (26) and tighten jam nut se- curely as shown in FIGURE 32. IMPOR T ANT! Make sure the cables are running in the grooves of all pulleys. 3/8 X 2” 89 82 AB CABLE 45 26 • Route the AB CABLE (4 ...

  • Life Fitness 849 - page 27

    27 STEP 33: FIGURE 33 • SECURE the ball end of the PRESS CABLE (44) and two 4-1/2” PULLEYS (48) to the SWIVEL PULLEY BRACKET (35) using two 3/8 X 2” BOL TS (89), four 3/8” W ASHERS (80), and two 3/8” LOCK NUTS (82) as shown in FIGURE 33. (NOTE: Loop the cable ar ound the pulleys prior to inserting it into the SWIVEL PULLEY BRACKET .) • ...

  • Life Fitness 849 - page 28

    28 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 34: FIGURE 34 • Route the threaded end of the PRESS CABLE (44) around one 4-1/2” PULLEY (48) and SECURELY assemble the pulley to the front slot of the PRESS ARM AD- JUST (36) using one 3/8 X 2-3/4” BOLT (90), two 3/8” FLANGE SPACERS (69), and one 3/8” LOCK NUT (82) as shown in FIGURE 34. (NOTE: ...

  • Life Fitness 849 - page 29

    STEP 36: 29 FIGURE 36 • SECURE the PRESS CABLE (44) and one 4-1/2” PULLEY (48) to the PRESS GUIDE ROD SUPPOR T (20) using one 3/8 X 2-3/4” BOL T (90), two 3/8” FLANGE SP ACERS (69), one 2-7/8 X 2-1/4” CABLE CLIP (116) and one 3/8” LOCK NUT (82) as shown in FIGURE 36. (NOTE: Loop the cable around the pulleys prior to inserting it into th ...

  • Life Fitness 849 - page 30

    30 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 38: FIGURE 38 • SECURE the swivel on the LEG CABLE (43) to the tab on the LEG EXT/CURL (32) using one 3/8 X 2” BOL T (89) and one 3/8” LOW HEIGHT LOCK NUT (83) as shown in FIGURE 38. (NOTE: Do not overtighten! Swivel clevis should rotate fr eely .) 8 9 LEG CABLE 43 32 83 LOW HEIGHT DO NOT OVERTIGHT ...

  • Life Fitness 849 - page 31

    31 FIGURE 39 IMPORTANT! Make sure the cables are running in the grooves of all pulleys. • SECUREL Y assemble one 4-1/2” PULLEY (48) to the horizontal bracket on the LEG FRAME (34) using one 3/8 X 2” BOL T (89), one 3/8” W ASHER (80), one 2-7/8” CABLE CLIP (67), and one 3/8” LOCK NUT (82) as shown in FIGURE 39. (NOTE: Before tightening, ...

  • Life Fitness 849 - page 32

    32 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 40 FIGURE 41 STEP 41: STEP 40: • Route the threaded end of the LEG CABLE (43) under the leg weight stack and throught the vetical bracket on the LEG WEIGHT STACK BASE (23) as shown in FIGURE 40. 3/8 X 2” 89 43 LEG CABLE 48 23 82 80 • Assemble one 4-1/2” PULLEY to the vertical bracket on the WEI ...

  • Life Fitness 849 - page 33

    STEP 42: 33 FIGURE 42 LEG CABLE 43 50 53 • Screw the threaded end of the LEG CABLE (43) approximately 1” into the end of the SELECTOR SHAFT (50) of the HEAD PLATE (53) as shown in FIGURE 42. • Insert one WEIGHT STACK PIN (75) into each weight stack on the 8500 GYM as shown in FIGURE 43. FIGURE 43 • If upon completion of assembly, the HEAD P ...

  • Life Fitness 849 - page 34

    STEP 44: FIGURE 44 34 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURELY assemble the PRESS SHROUD (113-has press exercise placard ) to the PRESS GUIDE ROD SUPPORT (20) and the PRESS WEIGHT STACK BASE (24) using four 3/8” X 1” BOLTS (114) and four 3/8” WASHERS (80). See FIGURE 44. • SECURELY assemble the PEC SHROUD (112-has warning label in ...

  • Life Fitness 849 - page 35

    35 FIGURE 45 STEP 45: • Attach the LAT BAR (18) to the ball end of lat cable using one 5/16” SNAP LINK (68). • Attach the AB CRUNCH STRAP (110) to the ball end of cable using one 5/16” SNAP LINK (68). • Attach the LOW ROW BAR (51) to the ball end of press cable using two 5/16” SNAP LINKS (68) and one 12 LINK CHAIN (74). Thank you for pu ...

メーカー Life Fitness カテゴリー Home Gym

Life Fitness 849のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 849の取扱説明書
- Life Fitnessの製品カード
- パンフレット
- またはLife Fitness 849の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Life Fitness 849の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Life Fitness 849の取り付け説明書、サービスマニュアル、簡易説明書、またはLife Fitness 849のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Life Fitness 849の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Life Fitness 849デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがLife Fitness 849を使用するのを助ける技術的文書のことです。説明書は通常、全てのLife Fitness 849ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Life Fitnessの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Life Fitness 849の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははLife Fitness 849の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Life Fitness 849に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Life Fitness 849デバイスの基本機能を使うにあたってのヒント。 Life Fitness 849のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Life Fitness 849に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるLife Fitness 849のメーカー/サービスへの連絡先に関する情報。

Life Fitness 849についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもLife Fitness 849の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLife Fitness 849で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)