Sub-Zero 315の取扱説明書

24ページ 0.63 mb
ダウンロード

ページに移動 of 24

Summary
  • Sub-Zero 315 - page 1

    inst all a ti on and op e r a t io n MO D EL 3 15 i ce m aker ® inst all a ti on and op e r a t io n ...

  • Sub-Zero 315 - page 2

    InTR O DUCTION T he Sub-Zero Model 315 is a restaurant-type ice mak er designed for home use . It produces the same high quality clear ice that you would expect from Sub-Zero . T his guide is intended as a resource for the installation and operation of the Model 315. Because it contains informa- tion on safety and maintenance , Sub-Zero strongly re ...

  • Sub-Zero 315 - page 3

    PRE-INST ALLA TIO N T echnical Information Y our Sub-Zero ice maker is designed and manufactured with the highest regard for safety and performance . It meets or exceeds the standards of UL, and CUL. Sub-Zero assumes no liability or responsibility of any kind for prod- ucts manufactured by Sub-Zero that have been altered in any way , including the ...

  • Sub-Zero 315 - page 4

    4 Pre-INST ALL A TIO N Pre-Installation Considerations Purer water will freeze first in the ice making molds . T he reason for this is that anything dissolved in water lowers the water’ s freezing temperature. T his concentrates most of the impurities in the ice mak er water reservoir where they may form hard deposits known as scale . T he Model ...

  • Sub-Zero 315 - page 5

    Pre-INST ALL A TIO N Moving the Unit IMPORT ANT NOTE: When you move the unit into the house using a hand truck or dolly , position the dolly on the side of the unit and secure the door so it does not open while transporting the unit. IMPORT ANT NOTE: The floor under the ice mak er must be at the same level as the surrounding finished floor . Electr ...

  • Sub-Zero 315 - page 6

    6 INST ALL A TIO N Plumbing Model 315 – Gravity Drain Model T he drain and inlet water tubes must be plumbed before connecting to the ice mak er . All horizontal runs of drain lines must have a 1/4" per foot fall. An air gap will likely be required between the ice mak er drain tube and the drain/waste receptacle . A stand pipe with a trap be ...

  • Sub-Zero 315 - page 7

    7 INST ALL A TIO N Plumbing Model 315P – Pump Model 1) Place ice mak er in front of installed location. Adjust leg levelers to approximately correct position. 2) Remove control knob , control panel and control access panel. 3) Route water inlet line from w all through ice mak er to the front. 4) Locate coil of 3/8" ID plastic drain tubing se ...

  • Sub-Zero 315 - page 8

    INST ALL A TIO N Completing the Installation IMPORT ANT NOTE: T urn on the water supply and check all fittings for leaks . Mak e certain the electrical harness is attached to the solenoid. Let your customer know that the ice mak er will not fill with water immediately , and that the first batch of ice produced should be discarded. Allow 24 to 36 ho ...

  • Sub-Zero 315 - page 9

    9 9 IMPORT ANT NOTE: T here is a part, pack ed with the ice mak er , that is required for this procedure . 1) Remove the hinge cover . 2) Remove the door by removing the (4) screws that secure the door to the door hinges . 3) Remove the door hinges by removing the (4) screws that secure them to the cabinet. 4) Remove the (4) screws from the opposit ...

  • Sub-Zero 315 - page 10

    10 INST ALL A TIO N Panel Installation T he Model 315 will easily accommodate a door panel as long as you follow these points . F or any door handle hardware , we recommend near center pulls on edge opposite of door hinge side Y ou may have to countersink screw heads to ensure hard- ware does not interfere with panels fitting flush with unit doors ...

  • Sub-Zero 315 - page 11

    Once you have located the proper position for the hard- ware , mark the holes , remove template , and drill pilot holes for mounting of the hardware . W e recommend start- ing the first few holes , positioning the hardware , drilling remaining pilot holes , and securing the mounting brackets with the #8 x 1/2" screws . Install the door panel b ...

  • Sub-Zero 315 - page 12

    Knock-out 12 Hinge Cover Installation T his is to be completed after the unit is fully installed. IMPORT ANT NOTE: Install the 90 degree stop prior to installing the hinge covers . 1) Remove the backing paper of the adhesive pads and bond to the hinge as shown in the illustration. IMPORT ANT NOTE: Hinges must be free of dirt or grease before applyi ...

  • Sub-Zero 315 - page 13

    13 INST ALL A TIO N Installation Check List T he importance of the installation of your Model 315 ice mak er cannot be overemphasized. T he proper installation of your unit is the responsibility of the selling dealer or installer . T he following check list should be completed by the installer to ensure no part of the installation has been overlook ...

  • Sub-Zero 315 - page 14

    14 OPE R A T IO N Initial Start Up 1) Remove control box cover . 2) Rotate timer shaft clockwise until the cam is in the harvest position (switch button out). 3) T urn on water supply . 4) With unit plugged in, rotate ice maker control knob to the ON position. 5) Allow the unit to operate for 1 hour , and check the size of the cubes , if they are n ...

  • Sub-Zero 315 - page 15

    15 OPE R A T IO N Ice Production T here are two distinct cycles: freeze and harvest. 1 freeze cycle + 1 harvest cycle = 1 batch of 8 cubes . T he freeze cycle happens when water is sprayed against the freezing surface . T he harvest cycle is when the ice is released and water enters the ice mak er . A complete cycle tak es about 30 minutes . FREEZE ...

  • Sub-Zero 315 - page 16

    16 Cleaning IMPORT ANT NOTE: Never keep anything in the ice stor- age bin that is not ice; objects lik e wine or beer bottles are not only unsanitary , but the labels may slip off and plug up the drain. Never allow the ice mak er to operate without regular cleaning. The ice mak er will last longer if it is kept clean. Regular cleaning should happen ...

  • Sub-Zero 315 - page 17

    17 Cleaning the Ice Making System 1) Open the door and turn the ice mak er control knob to off . 2) Scoop out all of the ice , either discard it or save it in a ice chest or cooler . 3) P our 4 ounces of Sub-Zero ice mak er cleaner into the ice mak er reservoir . (Av ailable from a local Sub-Zero distributor or dealer , ask for part number 19034306 ...

  • Sub-Zero 315 - page 18

    ADJUST MENTS T here are three items that may be adjusted: cube size, bin ice level and harvest time . IMPORT ANT NOTE: Cube size and harvest time adjust- ments should only be done by a qualified service person. Cube Size Adjustment T he cube size control should only be adjusted to bring the cubes to the correct shape , the overall size cannot be ad ...

  • Sub-Zero 315 - page 19

    19 19 ADJUST MENTS Bin Ice Level Adjustment When the ice mak er shuts off the ice level in the bin should be even with the metal tube inside the bin. If the ice in the bin is too high or low , turn the ice maker control knob to adjust the bin thermostat. 1) T o lower the ice level, turn the knob counterclockwise . Usually a 1/8 turn will be enough. ...

  • Sub-Zero 315 - page 20

    20 TROUBLESHOO TING Problem Possible Cause Probable Correction T he ice mak er does not operate T he ice mak er is unplugged Plug the ice mak er in Break er tripped or fuse is blown Reset break er/replace fuse – if it happens again, call for service to check for a short circuit in the ice mak er Ice mak er control turned to OFF T urn ice mak er c ...

  • Sub-Zero 315 - page 21

    21 TROUBLESHOO TING Problem Possible Cause Probable Correction No ice falling in bin, but Ice may be stuck in the Check water supply – filter may be restricted ice mak er operates evaporator and the unit is "frozen up" Check inlet water v alve – screen may be restricted, or valve does not operate Hot gas valve may not operate -check a ...

  • Sub-Zero 315 - page 22

    22 W ARRANT Y "Sub-Zero Protection Plan" Full 5 Y ear W arranty and Limited 6th Through 12th Y ear W arranty on the Sealed System Full 2 Y ear W arranty on T otal Product Full F ive Y ear W arranty For f iv e years from the date of original installation, your Sub-Zero warranty covers all parts and labor to repair or replace any components ...

  • Sub-Zero 315 - page 23

    SER VI CE Service For Y our Ice Maker Please have model and serial number available . Contact your nearest Sub-Zero F actory Authorized Service Center in your area, your dealer or Sub-Zero F reezer Company , P .O. Box 44130, Madison, WI 53744-4130, call (800) 222-7820 or e-mail us at customerservice@subzero .com. F or installation questions or gene ...

  • Sub-Zero 315 - page 24

    Sub-Zero Fr eezer Company , Inc. 4717 Hammersley Road Madison, Wisconsin 53711 (800) 222-7820 (608) 271-2233 E-mail: customerservice@subzero .com 315IO 3/03 ® ...

メーカー Sub-Zero カテゴリー Ice Maker

Sub-Zero 315のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 315の取扱説明書
- Sub-Zeroの製品カード
- パンフレット
- またはSub-Zero 315の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Sub-Zero 315の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Sub-Zero 315の取り付け説明書、サービスマニュアル、簡易説明書、またはSub-Zero 315のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Sub-Zero 315の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Sub-Zero 315デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSub-Zero 315を使用するのを助ける技術的文書のことです。説明書は通常、全てのSub-Zero 315ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Sub-Zeroの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Sub-Zero 315の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSub-Zero 315の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Sub-Zero 315に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Sub-Zero 315デバイスの基本機能を使うにあたってのヒント。 Sub-Zero 315のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Sub-Zero 315に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSub-Zero 315のメーカー/サービスへの連絡先に関する情報。

Sub-Zero 315についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSub-Zero 315の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSub-Zero 315で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)