Eaton Electrical 110の取扱説明書

12ページ 0.4 mb
ダウンロード

ページに移動 of 12

Summary
  • Eaton Electrical 110 - page 1

    No. 7-309 August, 1999 Char -L ynn ® Power Steering 110, 230 and 450 Series Steering Control Units Repair Information 001 002 ...

  • Eaton Electrical 110 - page 2

    110, 230, and 450 Series Steering Control Units 2 See Note Below (lower right) Cast End Cap Special Tools Available 600057-000 Spring Installation Tool 5422-000 12 Point Drive Socket ( 5/16 in.) — -001 64489-000 6 Point (E10) Torx Drive Socket ( 5/16 in.) — -002 Note: Current -002 uses a Hex Head bolt – 1/2 inch across flats O-ring Groove Cap ...

  • Eaton Electrical 110 - page 3

    110, 230, and 450 Series Steering Control Units 3 Tools required for disassembly and reassembly. — Screwdriver (102-152 mm [4 in. - 6 in.] long, x 3 mm [118 in.] wide flat blade). — 6 Point (E10) Drive part No. 64489-000* or 1/2 inch socket for current hex head cap screws. — Breaker bar wrench. — Torque wrench (30 Nm [275 lb-in] capacity). ...

  • Eaton Electrical 110 - page 4

    110, 230, and 450 Series Steering Control Units 4 Cleanliness is extremely important when repairing a steering control unit. Work in a clean area. Before disconnecting lines, clean port area of unit thoroughly. Use a wire brush to remove foreign material and debris from around exterior joints of the unit. Although not all drawings show the unit in ...

  • Eaton Electrical 110 - page 5

    110, 230, and 450 Series Steering Control Units 5 12 Carefully remove anti-cavitation valves and manual steering check valve (roll pin and ball – if applicable) from bolt holes by tipping housing as shown (see figure 5). Control End Seal Gland Bushing Special Seal Gland Marked with Groove for Identification Replacement Teflon Seal (1 Piece) Sprin ...

  • Eaton Electrical 110 - page 6

    110, 230, and 450 Series Steering Control Units 6 17 Remove two bearing races and needle thrust bearing and seal from spool and sleeve assembly. 18 Tip housing onto port face. Remove spool and sleeve assembly from 14 hole end of housing (Figure 10). Attention: Do not bind spool and sleeve in housing. Rotate spool and sleeve assembly slowly when rem ...

  • Eaton Electrical 110 - page 7

    110, 230, and 450 Series Steering Control Units 7 Low T orque Spring Spacers (2) Standard T orque 23 Screw a #10-24 machine screw into end of check ball seat. Then lift seat out of housing by pulling on screw with pliers. 24 Remove two seals from check valve seat. 25 Tip housing to remove check ball and check ball retainer. 26 Do not remove any val ...

  • Eaton Electrical 110 - page 8

    110, 230, and 450 Series Steering Control Units 8 spring slots of spool and sleeve. Position centering springs on bench so that extended edge is down and arched center section is together (figure 15). Next, with spring notches facing sleeve, insert one end of entire spring set into spring installation tool. 8 Compress extended end of centering spri ...

  • Eaton Electrical 110 - page 9

    110, 230, and 450 Series Steering Control Units 9 17 Install retaining ring in housing (figures 19 and 20). After installing ring, pry around ring circumference with screwdriver to properly seat ring in groove. 18 Clamp housing in vise, as shown in Figure 21. Clamp lightly on edges of mounting area; do not overtighten jaws. Note: Check to insure th ...

  • Eaton Electrical 110 - page 10

    110, 230, and 450 Series Steering Control Units 10 23 Lubricate and install 72,6 mm [2.86 in.] ID seal in spacer plate or gerotor (meter), (ref.) see note page 2. The lubrication will hold seal in place. 24 Align star valleys (reference A) with marked drive (reference B). Valleys must align with pin. Note parallel relationship of reference lines A, ...

  • Eaton Electrical 110 - page 11

    110, 230, and 450 Series Steering Control Units 11 28 Install 7 dry cap screws (and seal washers if applicable – see figure 26) in end cap. Pretighten screws to 17 Nm [150 lb-in], then torque screws to 25-30 Nm [225-275 lb-in] in sequence shown in figure 27. Eaton Corp. Hydraulics Div. Eden Prairie, MN 55344 Char-Lynn ® 000-0000-000 000-0000-000 ...

  • Eaton Electrical 110 - page 12

    Form No. 7-309 Copyright Eaton Corporation, 1981, 1988, 1993, and 1999 All Rights Reserved Printed in USA Each Order Must Include the Following: How to Order Replacement Parts 1. Product Number 2. Date Code 3. Part Name 4. Part Number 5. Quantity of Parts For additional literature contact Eaton Corp. Hydraulics Division 15151 Highway 5 Eden Prairie ...

メーカー Eaton Electrical カテゴリー Power Supply

Eaton Electrical 110のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 110の取扱説明書
- Eaton Electricalの製品カード
- パンフレット
- またはEaton Electrical 110の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Eaton Electrical 110の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Eaton Electrical 110の取り付け説明書、サービスマニュアル、簡易説明書、またはEaton Electrical 110のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Eaton Electrical 110の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Eaton Electrical 110デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEaton Electrical 110を使用するのを助ける技術的文書のことです。説明書は通常、全てのEaton Electrical 110ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Eaton Electricalの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Eaton Electrical 110の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEaton Electrical 110の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Eaton Electrical 110に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Eaton Electrical 110デバイスの基本機能を使うにあたってのヒント。 Eaton Electrical 110のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Eaton Electrical 110に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEaton Electrical 110のメーカー/サービスへの連絡先に関する情報。

Eaton Electrical 110についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもEaton Electrical 110の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEaton Electrical 110で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)